Dold Ford Focus (Ford Focus) of different generations. Discover Car Disk Ford Focus Ford Focus 3 Valid Tire Sizes

The competently selected kit and the size of the wheels on the energetic Ford Focus car will give him not only additional beauty and aesthetics, but also improve dynamic indicators. Each owner a passenger car Focus has the opportunity to purchase alloy wheels with identical diameter, rim and departure, as well as standard wheels installed in the factory assembly.

You can also make a small restyling and install wider wheels with the smallest departure. As a result, Ford will look original and will slightly increase its dynamic indicators and stability on the track.

Almost always exists alternative option Replace the standard wheel and disk by analogues with large size rim. Ideally, after this, the vehicle should not have problems.

More massive wheels as a result will "require" use wide tires, and they contribute not only to improving dynamic indicators, but also high level Brakes, respectively, the driver can feel calm even with aggressive ride.

The car owner must independently make a choice in favor of certain wheel sizes. Immediately before choosing and installing, it is necessary to carefully examine the basic parameters recommended by the car manufacturer:

• rim;
• breaking;
• departure;
• wheel size.

These parameters must match the characteristics. vehicle. If certain problems arose when installing the wheels with non-standard parameters, then for help it is better to turn to experienced specialists.

Detailed characteristics of wheel sizes, tires and disks on model Focus 1 and 2

According to the overall departure indicators ET for wheel disks Ford, the maximum deviation from the standard sizes should not exceed +/- 5 mm.

The disk size implies the optimal width of the product with respect to the tire no more than 20-30%. As a rule, tuning lovers and ordinary drivers do not always pay special attention to these indicators.

Many manufacturers began to produce various non-standard autody regardless of the width and height parameters. In addition, with a more wide disk, manageability indicators will improve.

But only in the case when tires and wheels with identical dimensions are used. For example, tires with a width of 185 mm are perfectly combined with discs 205 7J, 205 6J, 195 6J.

For Russian configurations, Ford focus in standard form was established by factory tires with a high profile, in contrast to identical models manufactured in foreign industries.

This allows you to install any bus, according to the specified instruction from the manufacturer, depending on the wishes and block control settings.

Factory characteristics from Ford:

1. the total number of bolts for installing the wheel - 4;
2. the central diameter of the fasteners -108 mm; in the designation 4/108;
3. the dimensions of the diametrical holes of the wheel of the wheel under the hub - 63.3 mm, is indicated by D63.3.

If you use holes with smaller diameters, the wheel cannot be installed on the hub. For diametrical holes with large indicators, special adapter rings must be applied.

Standard disk size

As for the question of whether there will be a chain of the fever, it is necessary to follow the optimal recommended wheels of the wheels and install tires with a lower profile.

For example, you can use tires 205/50 / R16, but they do not guarantee a uniform calm ride - problems may arise at the time of the tunnel hook.

It is best to use tires 195/65 / R15, because the wheels with them become a little higher, due to which the performance indicators are improved.

The most popular and sought-after tire sizes on Ford Focus 1 and 2:

• 195/65 / R15;
• 185/70 / R14;
• 205/50 / R16;
• 185/65 / R14;
• 195/55 / \u200b\u200bR15.

If we are talking about ET indicators, then for cast and stamped discs, they are completely different. A smaller departure value indicates a wider range.

We also note that the secrets and nuts for the factory automobiles have a difference. The main thing is in the design and form. Cone corners of the working areas are adjacent to the working disk surface. Nuts on stamping have a smaller angle and, accordingly, not so much adjacent to the product.

Therefore, experienced professionals do not recommend using nuts for stamping as fasteners on casting. Too small contact area with a working surface, which means that bad mount for the car. It is necessary to take into account the fact that each tightening of the nut will gradually correct contact with the working surface.

To check the hitch of a new disk for the calipers, you must perform the following procedures:

1. install it on the valve;
2. perform screwing nuts to the hub;
3. fully spin the disk.

Fold Focus 2 Wheel Drive 2, 3

Example: Wheel breakdown on Ford Focus cars with 5/108 parameters. Many lovers of auto may have problems with the designation of these numbers. Therefore, we specify them in more detail their decoding:

1. number 5 denotes the total amount of diametrical holes for the fasteners of the wheel;
2. the number 108 indicates the size of the diameter of these holes.

Disc departure on models Focus 2 and 3:

1. standard size is 52.5 mm;
2. departure Wheel on Reystayling is 50 mm.

For beginners, departure is a rather complicated and difficult concept. If we talk simple words, then disk departure Indicates a common distance from the middle of the product to the main zone of fastening elements located on the hub.

• R15 / 195/65;
• R16 / 205/55.

The letter R denotes the radius of the wheel.

Wheel breakdown on focus 3

The total parameters of the 3 generation of focus are practically no different from similar models 5/108.

Wheels on 3 Release Ford Focus

The third release of the famous focus model was implemented in 2010. The car was presented at the famous Salon in Detroit. The vehicle was presented in several bodies: sedan, wagon and hatchback.

It is known that Ford Focus. Until now, is one of the most sought-after cars around the world. Annually selling, and lovers of this car are satisfied with its simplicity in operation and stylish design.

The American manufacturer has achieved such results due to the high ratio between quality and cost.

In addition, 3 car release was performed in kinetic design. Many admired the originality and uniqueness of this car. On the track, the focus demonstrates excellent characteristics and indicators of control, starting acceleration and stable ride.

Good management on the vehicle achieves due to improved balance between discs and tires. Therefore, it is necessary to consider the main type of rubber and disk parameters for optimal ride on focus 3.

Optimal wheel sizes

Each car released by the American Ford Line has certain size sizes and tires recommended by manufacturers. Consider the main parameters required for good handover by car:

1. Disk dimensions: 16, 17 and 18 inches;
2. Tires 235/40 / R18, 215 / 50R17, 205 / 55R16;
3. Disk width ET50, ET55.

Absolutely for all wheel sizes 5/108 fastening elements with a central diametrical hole of 63.3 mm and a heap of 14.5 mm are used.

When registering the main indicators, everyone can decide on the choice of wheels on the Focus Model 3. As an optimal option, it is recommended to use original factory products or similar products from eminent brands.

Branded models are more durable and reliable because they are specifically produced for a particular focus model. This is a very important factor, even in that situation when the car runs on a deep pit or crack.

As a result, the wheelheaper is not deformed, and the driver continues to control the control of the vehicle.

The discs are selected according to the width of the tire, they must be identical. In most cases, the American company produces original factory stamps on focus 3. Such discs are perfectly operated in sophisticated conditions And have a small cost.

In addition, acquiring such discs, you can not take care of the amount, because they are automatically suitable for standard focus wheels.

In compliance with the competent recommendations, the car's amateur does not have problems with the choice of wheel size on the Ford Focus car. If you wish, you can use non-standard models, but it will be necessary to change the technical components of the vehicle slightly.

Using proper tires overall dimensions Allows you to avoid problems on the road, save handling. But many owners are installed on Ford Focus 3 non-standard diameter rubber. The use of larger wheels can cause serious problems - it is necessary to carefully approach the selection of cylinders.

ATTENTION! Found a completely simple way to reduce fuel consumption! Do not believe? Auto mechanic with 15 years old also did not believe, until he tried. And now it saves 35,000 rubles per year in gasoline!

The size of the tire is not the only parameter to take into account which you must necessarily when buying the wheels in the auto shop. There are still a number of important parameters with which you need to get acquainted in advance. When choosing, you need to consider:

• features of the design of a particular vehicle, installed engine - diesel, gasoline, other;
• disk type - stamped, forged, cast;
• the magnitude of the contact stain and the load on the wheel.

It is important to take into account all the nuances listed above. Only so you can avoid standard errors when choosing new wheels. Cars 2018-2019 releases are supplied in two sets:

• stamped steel discs with tires 205/55 R16;
• alloy alloy wheels with rubber 215/55 R

The options listed above are standard, staten sizesThe installation of which is carried out directly at the factory, when assembling a car. It is the above options that are optimal for this vehicle. Size 16 is standard, positioned as a regular diameter. However, it is possible to install non-standard wheels With a big radius.

It should be noted: In dealerships, the exhibited cars are usually supplied with a rubber corresponding to standard sizes as defined by the manufacturer. However, it should be noted - on sale there are new cars on the Continental and Bridgestone rubber.

The reason lies in the annual change in value specific models Tires. After graduating from a large batch purchased wholesale from one manufacturer, the plant can make a choice in favor of another brand. This explains the presence of different tires.

What non-standard dimensions can be put

The manufacturer laid in the design of the car the ability to install wheels with a diameter of 17 inches. Moreover, the maximum permissible size in which the operation of the vehicle will remain safe - 215/50/17. However, on each modification of the vehicle there are specific dimensions.

To familiarize yourself with them, it is not necessary to contact the manufacturer or in service center. All the necessary information Located on a special plate located on the door rack from the driver. The ability to install non-standard disks or tires by 100% depends on the specific conditions and the car itself. Main conditions:

• new tires and equipped with them drives should not hurt brake caliper, other mechanisms, fenders;
• the breakdown should be standard - 5 × 108 mm;
• the diameter of the central opening is 63.3 mm;
• the diameter of each heel is 14.5 mm.

Another important condition - rubber should not touch the body even with full turn, compression of the rack. The design of the car is allowed to install the wheels of three different diameters:

• 16 inches - 205/60/16;
• 17 inches - 215/55/17;
• 18 inches - 235/40/18.

The last option is the least preferred - however, on the disks of the diameters of 18 inches, the machine looks much more presentable. However, it is easy to damage the disc in just 40 mm high.

What is especially sad when using alloy models. The cost of such discs can reach 15-25 thousand rubles per 1 piece.

What is the pressure in tires

One more mandatory condition safe operation The car is the pressure corresponding to the established standards. You can familiarize yourself with these parameters yourself without leaving the car. The nameplate with all the necessary data is located right on the door rack. However, the owners often do not pay attention to this parameter.

It should be noted that non-standard pressure leads to serious problems. Packed wheel:

• can burst right on the road - even the slightest impact will damage the integrity of the rubber structure;
• the central part of the tread is rapidly wears - uneven stratification leads to the need to replace tires;
• controlness worsens, suspension wear increases.

The bad wheel is less dangerous. However, low pressure will cause the rapid erase of the tread on the sides of the wheel. Uneven wear and wide contact spot also lead to a deterioration in manageability, other issues. It should be noted that the recommended pressure for tires differs depending on the level of load and some other parameters. For speed up to 160 km / h:

In most cases, it is enough to pump the front and rear wheels to a value of 2.1 bar. However, with full load, it is necessary to increase the pressure to 2.4 on the front wheels and 2.8 on rear wheels. This will preserve the responsiveness of the steering wheel, make the control of the laden machine more comfortable.

Overview of the best summer and winter tires

With intensive operation, rubber is required to change. And for summer and winter drive, it is required to purchase a different kit. Good choice Model Continental Premium Flat 205/55 R16. This rubber is characterized by high quality, a special composition of rubber. The presence of a rigid side frame allows even with a fully swashed wheel easily reach the nearest tire.

Michelin Pilot Sport 4 is supplied with an additional nylon layer. Occasionally enhances the working part of the surface, it allows you to prevent a random gap with a strong impact. The name of this model does not accidentally have a Sport console. It is perfect for fasteners of fast ride.

Bridgestone Potenza S001 due to asymmetric tread design has excellent braking characteristics. The presence of special drainage lamellas eliminates the likelihood of aquaplaning. The driver is safe even in difficult road conditions.

Goodyear Eagle Sport is positioned by the manufacturer as a sports option. In fact, this is a budget analogue of the tire models discussed above. The cost of goodyear is an order of magnitude cheaper (the difference is 2-3 thousand rubles). Wherein driving performance Practically do not differ from more expensive models.

Tunga Zodiak - domestic production. Represents a budget option Rubber, produced in an Omsk plant. It works well with an expensive of any quality. However, with long-term operation, the likelihood of the appearance of hernia, deterioration of balancing.

Nokian HakkaPeliitta 9 Run Flat is one of the most expensive, reliable tires in the segment. winter tires. The composition of rubber is referred to as Special Clinch. The protector has a V-shaped form. Which provides perfect contact with the roadpapers.

Nokian Nordman is a budget analogue of hackcappelites. The cost of this model from Nokian is 2-3 times less. Excellent quality is combined with accessibility.

Yokohama IG55 is positioned by the manufacturer as a rubber specially designed for operation in severe frosts. At its price, comparable to Nordman. Owners celebrate a soft move and low level Noise regardless of the speed of movement.

Michelin. X-Ice North It is a real standard in the sphere of the tire industry. The total number of spikes is 250 pieces. It provides excellent clutch with an expensive even from the winter time period.

Cordiant Snow Cross. - this is a budget version winter rubber. Due to the unique design of the tread, it is possible to achieve good clutch With expensive. Snow-Cor technology applies. The protector independently cleans itself from snow, dirt.

To choosing rubber, especially winter, it is necessary to approach with full responsibility. Properly collected wheels ensure the safety of the driver and its passengers on the road.

Select the correct size of the Ford Focus 3 wheels - easy. The factory parameters correspond to only one size of 16 inches, so there should be no problems with the choice. The car was produced in the bodies of the sedan, hatchback and wagon. Completed both alloy alloy products and steel, produced by stamping. Tires and disks for "focus" in the third generation is important to choose correctly and efficiently. Auto has a long history, for 20 years, Ford has been producing this popular model. Recently, the fourth generation has been presented.

Since 2011, the third generation of the car has gained very high popularity in Russia. In 2018, he was replaced by a newer, fourth generation, which embodied all the qualities of the predecessor and gained many new ones.

Winter tires on Ford Focus 3

To date, on the shelves of auto shops, a very wide range of products for the machine is presented. This also applies to the wheels on Focus 3, which manufacturer are limited only in one size - by 16 inches.

The owners of this popular car, like any others, are also faced with the need to replace tires before the onset of a certain season. In this case, you have to choose from a variety of options presented in products. It can be both very famous and expensive brands and models of cheaper.

The selection of the brand and the properties of rubber depend only on the personal preferences of the motorist.

It is worth remembering that even the products of very expensive producers can be absolutely useless with improper operation and storage. It is very important to select products only with the correct dimensions and constantly monitor their condition. This also applies to the installation of tire pressure, which is regulated by the manufacturer and is indicated in the technical documentation.

The market of the country is rich in suggestions for sales of rubber in various performance and having different characteristicsthat are even suitable for the most demanding car owners. This is related to the great popularity of the car.

It is also worth noting that from right choice Tires will depend on the safety of the driver and passengers.

In difficult weather conditions, on slippery coating from installed rubber Often, people's lives depend on. In addition, tires have a huge impact on the level of wear of the details of the chassis, controllability, dynamic characteristics And other qualities.

How to choose

For high-quality selection of tires on the Ford Focus car 3, you need to know what the main differences are and what they are.

For seasonality, the tires are:

• Summer. Only starting from the temperature from five degrees Celsius can be operated. The tread pattern in such tires is not very pronounced, compared to winter. Operating summer products at elevated temperatures, they become solid and cooled themselves. Suitable for ride at high speeds on good roads.
• Winter. Can only be operated in winter, with temperature regime Below zero degrees Celsius. The protector of these tires is much deeper than the summer analogs. At cold temperatures, rubber independently heats up and increases its own elasticity. In this regard, the grip with the road surface increases. It makes the car more manageable, reduces the distance brake path and increases dynamic qualities. The service life of winter rubber is usually more than a summer, since the average speed is less.
• All-season. Often the name is "universal". They are middle link between winter and summer. Manufacturers indicate that use rubber this type You can independently of the season. However, professionals are recommended to establish this type only when the temperature on the street is ranging from -5 to +7 degrees Celsius. In fact, universal tires are inferior to the winter in the cold season and summer - in warm. Therefore, it is popular in countries with relatively warm climates and dry winters. It is forbidden to exploit them in very hot and very cold weather.

Read 5 min.

Third generation Ford. Focus was presented in early 2010 at the North American Motor Show in Detroit. The car was performed in 3 bodies - sedan, hatchback and wagon. Ford Focus is one of the most popular machines on the world market, whose share is constantly growing. This result is achieved by an excellent price ratio - quality. Moreover, the third generation was made in the "kinetic" style, which looks very modern and attractive even today.

Among other things, Fordfokus has excellent characteristics On the road, and to steer them - one pleasure. This is largely achieved due to the correct selection of discs and tires that are responsible for the stability and the hook of the car. In our article we will discuss how to choose what rubber and which wheels to put, what their size and other issues related to wheels on Ford Focus are.

Sizes of wheels

Depending on a certain car model, its weight and body type, it has its own specific disk size and tires. As for the Ford Focus, then for this machine, the wheel parameters are shown below in the table.

For all sizes it is necessary to choose fasteners 5 to 108, central hole - D 63.3 mm, and the diameter of the place under the heel is 14.5 mm.

Given these parameters, you can clearly figure out which wheels to put a third-generation focus on Ford, which rubber to choose, be it summer or winter. Optimal option - This is an acquisition original disksBut if you choose the right size, you can give preference to another company.

Choosing disks

If you are not sure what rubber to choose which discs to put, then you need to know several features of the Ford Focus car. For this model, you only need to install high-quality discs that would not only emphasize his beautiful appearance, but also ensured the maximum dynamic indicators.

The original wheels have ease, while they are strong enough. It is extremely important because even when he gets into a serious pit, it will not collapse, and the driver will not lose control. That is why it is important to choose the proper discs in size. Moreover, the value also has summer tires - It should also be high quality.

Ford manufactures its own tires and wheels, the size of which is perfect on the focus of 3 generations. You can buy them in specialized stores or on the Internet. For the most part, these stamped discs that combine excellent performance features and low price. The advantage of the acquisition is that they are that you will not need to worry about the size - they are suitable for your focus with 100% guarantee. By the way, their replacement will not violate the conditions of warranty service, which is also an undoubted advantage.

Disc service

In order for Ford Focus to never grieve you, always follow the status of wheels and rubber. If they are damaged or worn, then it is necessary to immediately replace the tires and wheels, and not cook, ride or pan.

Even if the size is suitable, the replacement of the disks is simply necessary in the following cases:

• If there are lateral or radial beats.
• During deformation.
• With violations of the geometry of the holes.
• When forming corrosion.

If excessive beating (any of the types) is observed on the wheel, it may cause vibration formation while driving. At the same time, choosing new discs, they must be approached by the level of permissible load, departure, diameter and many other parameters. Otherwise, in the presence of inconsistencies, the resource of the wheel and bearings will decrease, the brakes will cool well, and the speedometer can show incorrect numbers.

In order to determine the level of wheelbeat on Ford Focus, you need to use a special clock-type device. The disc must be put on the balancing machine, while the tires can be removed and left on the spot. By installing the device, we turn the wheel to one full turn and fix the testimony obtained. If they exceed the norm, it is necessary to carry out balancing. If it does not help correct the problem, then the only option is to replace the disk. It should be noted that if the testimony influenced scratches or other damage (including tires), then the disk can be left.

If the tire size is not suitable for the car, it can cause many different problems. One of them is water from the trajectory of movement. Thus, you will always have to gather, and this is inconvenient. It should be noted that this may be caused by another reason, for example, a disk or tire defect. Deviation from the trajectory is observed if the tires have different sizes. You also need to know that this situation may occur exclusively with the front axle.

So, as we managed to find out that proper selection Rubber and disks have a huge effect on the behavior of the Ford Focus on the road. If you do it wrong, then the car control will not only be uncomfortable, but also unsafe. Do not save and acquire cheap and non-original discs, as well as low-quality rubber. Always check the size of rubber and disks by comparing it with recommendations from the manufacturer's factory. Thus, you can achieve maximum effect and squeeze everything that your car is capable of.