Fuel filter is one of the most important aggregates for any car. Experienced motorists should know exactly where the filter is located, which helps improve the technical characteristics of the machine. Additional knowledge relate to the features of the operation of the aggregate, the need to replace it.

Renault Duster.

Engines used for Renault Duster.Different with an unpretentious attitude to the quality of the fuel used. It is possible to use gasoline and diesel fuel. The proposed filter has a high level of quality, due to which it is guaranteed the possibility of its long-term operation. Most motorists successfully refuse to replace the filter, regardless of the type of fuel used.

Despite the high level of reliability, in some cases the filter still fails, and its replacement becomes mandatory. With installing a new unit, a motorist can successfully cope.

Wanting where fuel filter On Renault Duster, only one answer can be provided: in the fuel pump. The filter is performed as a mesh. However, the experienced Duster owners recommend taking care of the installation of a full-fuel filter into a pump compartment, since the dummy is originally located in the desired location.

Instructions for installing an additional fuel filter

Installation takes place in two stages:

1. A screwdriver unscrew the clamps of the nozzles, hexagon - fastening the parts to the car housing.
2. At the next stage, the nozzles are connected and the filter is removed. It is changed to a new one that is installed in the reverse order.

If you plan to install the engine located under the rear chair, it is recommended to initially leak the seat and remove the hatcher of small sizes. Now you can see the terminal and nozzles responsible for feeding the power and fuel to the filter. After the work event, it is recommended to reduce the pressure of the fuel system, since, otherwise, the car owner may encounter excessive risks under the influence of fuel injection. Only after the preparatory measures the filter housing is unscrewed and the element is dismantled. Then the fuel is merged and the unit is replaced with a new device.

Attention! After that, the car is assembling with a further check of the tightness of the installation.

Causes of clogging of the unit for fuel purification

Filter clogging can occur with any engine. In most cases, this situation occurs if a substandard or unsuitable fuel with foreign particles use to refill vehicles. Application of quality diesel fuel or gasoline reduces the risks associated with the engine malfunction.

Signs of filter clogging:

• unstable engine functioning on idling or for harsh pressed on the accelerator pedal;
• no ability to use the motor on full power;
• regular and sudden installation of the power unit.

If unwanted problems with the Renault Duster institution are noted, it is best to replace filter parts. In addition, you can cope with the task yourself.

Renault Logan.

Mandatory task is an understanding where the fuel filter is located on Renault Logan and the replacement nuances for the further successful use of cars.

Timeliness maintenance - This is one of the most responsible tasks of the owner of the car. For supporting good condition The machines are recommended to regularly install the fuel filter. However, where is the fuel filter on Renault Logan? It all depends on the year of the car.

1. On the Logan of the first generation (2005-2006 years of release) you can find a filter from a gas tank in place where fuel pipes come out. For this reason, you need to focus on right side District rear wheel.
2. On cars that were released after the third quarter of 2006, the fuel filter is right in the gas tank in the same place where the pump can be detected. This option guarantees the maximum level of reliability, as a result of which the car is ready to serve successfully and properly.

Understanding where the fuel filter is on Renault Logan, allows you to navigate with the further replacement process.

Fuel filter replacement features

The first mandatory stage is to prepare for the installation of a new fuel filter. During the operation of any engine, the fuel is under constant pressure, which is saved for two or three hours after stopping the power unit. The replacement is best to spend only after a couple of hours passes. If there is no possibility of expecting a favorable moment, the pressure from the fuel line needs to be reset.

How to reduce too much high pressure:

1. At the very beginning, raise the back chair and turn off the block of wires on the fuel pump vehicle.
2. Then the motor is launched and waiting for the fuel residues.
3. After the motor is independently stuffed, within a few seconds turn it with a starter. It is this stage that denotes the reduction of working pressure.
4. Now it is allowed to disconnect the terminal with a minus designation from the battery.
5. After the pressure managed to reset, you can disassembly.

To replace the fuel filter, work on both sides to the fittings recorded by tips and red, green locks. The order of removal of nozzles does not play any role, but it is best to navigate the arrow placed on the filter housing. The arrow denotes the fuel direction. Installation is carried out in reverse order dismantling.

After replacing all components of the fuel wire and the terminal to the battery fill the fuel system. For this include ignition for a few seconds. During the short-term operation of the pump, the tightness of the filter, nozzles, clamps check. The regular replacement of all aggregates guarantees the possibility of successful and secure trips by car, because it is supposed to maintain the reliability of the technical system.

It is important to remember the tasks of the fuel filter. So, this device is required to successfully purify gasoline or diesel from the following components:

• deposits;
• mud;
• rust.

Taking into account the low quality of the fuel used, it can be understood how important the use of a good and functional filter becomes. The manufacturer recommends a replacement procedure every 120 thousand mileage kilometers. However, if poor-quality fuel is used, the event is recommended every 50-60 thousand kilometers.

Chevrolet Cruze.

Chevrolet Cruze. - One of the most popular cars. It is this car that earn an ideal reputation due to high level reliability and optimal technical characteristics. However, in order to mark all its advantages, it is imperative to maintain the fuel system in perfect condition.

So, where is the fuel filter on Chevrolet Cruz and what approach is required to support its good condition? It is interesting to note that Chevrolet does not install such an element as a fuel filter. The full-fledged unit in Cruze is replaced by a conventional grid responsible for filtering the fuel used.The mesh can be changed to the fuel filter.

Car manufacturer Notes that the fuel pump is installed for the entire service life of the car. For this reason, its replacement is inappropriate. Despite this, the low quality of diesel fuel and gasoline in Russia contributes to the need to know where the fuel filter is located, how to change it.

When to change the mesh to filter fuel

• lack of coordinated motor operation;
• loss of power of the power unit and the feeling of "failures" when pressed on the gas pedal;
• reducing the dynamic machine;
• drozhnya with a sharp press on the gas pedal.

All four features are sufficient to think about replacing the filter grid. In most cases, installing a new grid is recommended after 60 thousand mileage kilometers.

How to replace

Before independent activities, it is recommended to carefully examine the instructions in order to know not only where the fuel filter is located, but also to successfully cope with the replacement.

The first stage is preparation. Only after the relevant preparatory activities can be carried out by the procedure for replacing the filter (mesh). It is best to use the original product from Chevrolet, but you can choose domestic products. Considering different opinions, it can be understood that the choice depends only on the preferences of the motorist. Domestic filter grids are always available taking into account the characteristics of Russian fuel, so their service can be long and successful.

Main works are recommended to be carried out before discounting the pressure in fuel system. To do this, turn off the ignition and dismantle the block fuse. After completing the task, you need to allow you to work for a time for some time. Only after the machine stalls, the pressure will be able to reset.

So, how to further conduct filter replacement activities:

1. Luke for fuel pump Chevrolet Cruze is absent, so in order to get to it, you will have to dismiss the entire tank.
2. The wires that need to be carefully disconnected to the pump with a harness.
3. Now it will be possible to see several pipes, along which the fuel enters the pump and comes out of it. Pipes with locks are disconnected with a flat screwdriver.
4. At the next step, disconnect the lid of the fuel pump, acting extremely carefully and turning the locking disk counterclockwise. Remove the locking disk, and then - the pump.
5. On the fuel pump are connectors that need to be disconnected. In addition, four latches are pressed from the housing.
6. Top part fuel pump Must be removed without problems.
7. If the engine problems are due to the filter grid, you can note the presence of dirt. Cleaning the item will not help, so the mesh will have to be replaced and install all the parts in the reverse order.

Successful replacement of the filter grid on Chevrolet Cruze can be carried out even independently!

Kia Rio.

One of the most important issues - where is the fuel filter on Kia Rio? This question is asked by many car enthusiasts, because Kia Rio. It is a comfortable and worthy modern car capable of delight with its dynamics. For the successful use of the engine, it is recommended to replace the replacement every 2 years or through every 60 thousand kilometers passed. Checking the fuel filter is desired once a year or every 30 thousand kilometers.If we neglect the tips, unwanted fuel particles will pollute the nozzles and worsen technical specifications cars. In addition, the symptoms of the contaminated fuel filter lead to a violation of the motor functionality, which is forced to work for wear.

Opportunities for self-substitution

The event can be carried out independently or on a hundred. In the first case, it will be possible to save, and in the second case it will still have to pay for the procedure. It should be noted the compact dimensions of the fuel filter and the efficiency of the procedure.

The first stage is to reduce the pressure of the fuel system:

• inclusion of the neutral position of the gearbox and manual brakes;
• removing the rear armchair pillow, hatch caps from fuel tank;
• schigs the clamp for disconnecting the wire blocks;
• running the motor to generate fuel residues;
• turning on the starter for a few seconds.

Now it is allowed to remove the old fuel filter:

• clamps are gently compressed;
• pipelines are disconnected from the filter;
• liberate the clamp;
• pull the filter.

Now you need to install new filterBy performing all actions in reverse order.

If it still becomes a preferred option with a maintenance station, you need to count on the minimum price of 1500 rubles. This cost is due to the ease and speed of work.

Toyota Corolla

Toyota Corolla - This is a car that has a fuel filter guarantees uninterrupted and long service of the motor. The design of the original device differs from other variations of the device. At the same time, execution features are always dependent on the modification of Corolla.

It is envisaged to conduct replacement activities every 50-100 thousand mileage kilometers.

So, how do the original fuel filters for Toyota Corolla differ?

• the device is based on cells, which guarantee successful fuel filtering;
• the plastic body of the fuel supply is the base of the filter element (in this way, wondering where the fuel filter is located on Toyota Corolla, it can be noted that its location is the fuel block);
• for fuel purification, traditional paper parts are used, as well as fiberglass with polyester.

Even modern and reliable use of the filter does not guarantee long service. On the manufacturer's recommendation, the replacement is recommended every 80,000 mileage kilometers, but this information is approximate.

On the domestic market Could offer at least three types of fuel filter for Toyota Corolla. Products comes from the original brand, Chinese and Korean manufacturer. At the same time you need to choose a fuel filter that is suitable for toyota car Corolla taking into account the species of the model (until 2007 release or after). Until 2007, a mandatory replacement of the filter fuel pump is envisaged, since 2008, a separate installation of filter parts is allowed.

Ford Focus III

IN Ford Focus. III The fuel filter is installed fuel pump, which is located in the tank. Such a tricky location immediately complicates independent replacement of the device.

At the same time, it is necessary to know not only where the Ford Focus Fuel Filter is located, but also the features of its execution. The car has an unspeborified fuel pump, therefore it is planned to replace not only the filter grid, but also the pump. Many car enthusiasts go to the American manufacturer, but such work is always risky and still better focus on official recommendations.

So, knowing where the fuel filter is on the car, it is possible to envisage it self-substitution And take care of a clear understanding of all the advice, each stage of the upcoming work. Only proper service will allow you to maintain technical condition Any car in perfect order.

The car fuel filter belongs to the number of "consumables", the need to replace which many car owners simply forget. Others opposite change it almost with each maintenance, motivating it with a lengthy explanation: they say, so the engine "rus" is noticeably better. We tell what is dangerous to replace the external fuel filtering element and explain when you actually need to produce this operation.

Why do you need a fuel filter

The fuel filter performs a single and very ordinary function in the car - cleans the fuel from all sorts of physical contaminants - garbage, dust, outsiders and grades, in a word, everything that should not get inside the engine internal combustion. The remaining properties of the fuel does not change in any way.

The filter element is in an absolutely every car, regardless of whether the motor on gasoline, diesel or gas is working - any type of fuel passes stepped cleaning before it is injected into the combustion chamber in the form of a fuel-air mixture or pure fuel. At the same time, cleaning is carried out at least two stages - a coarse filter, and then fine cleaning. Just the second of them and are usually a periodic replacement, the timing of which each manufacturer specific model The car regulates independently. Let us dwell on the gasoline modifications of machines.

In the process of refueling fuel from the column hose poured directly to the tank. At the same time, in the container gets like all kinds of dirt with filling pistol, as well as dust, located during operation on the walls of the neck, and suspension, located directly in the tank capacity. From the gas tank relatively dirty fuel on modern cars It is closed by a submersible pump equipped with a nylon mesh that does not allow to penetrate the fuel line of a large fraction. Then the fuel falls into a fine cleaning filter, which is delaying dangerous for the injection system and engine, but rather small particles in size over 10 microns. Such a cleaning is enough to ensure safe and reliable operation of the injection system and the entire motor throughout full time His services. All that is required from the car owner is from time to time to change its resource "consummer", that is, a filter.

Types of filters

At this place will immediately arrange: the owners are relatively new gasoline cars and this action is not required for a long time. Most manufacturers have already got rid of the endless fuel filter of the fine cleaning and placed it directly into the gas station hidden in the tank. Such a filter is designed for the entire service life of the machine and does not require audit or replacement. Even though, for example, with an average consumption of 10 liters per 100 km of the path for 100 thousand km, the pump consists of a motor of about 10 thousand fuel liters, and the whole volume passes through the filter!

Owners of old cars, the possibility of replacing the filter element opposite was provided - to do this can be either directly in the pumproom space, or under the bottom of the car. In this case, the filter element is placed in a separate housing and embedded into the fuel line on the site between the tank and the ramp. To replace the filter, you only need to reset the pressure in the system and disconnect a pair of clamps or quick-proof clamps. The frequency of the operation is an average of 30 to 120 thousand km, according to the recommendations of different brands.

When to change

Whatever the recommendations of manufacturers for the replacement of external filters, the actual life of their service is very difficult - it is entirely dependent on the quality and area of \u200b\u200bthe filter element, but also from the volume of contaminants in the tank specifically your car. In practice, in modern realities, a remote fuel filter serves at least 100 thousand km without evidence to replace. Submersible filter, which is part of the fuel pump, does not necessarily need to be replaced until the fuel failure has occurred. And this approach is quite justified!

Filtering element of fine cleaning remains working smoothly until it can be enhanced by ramp necessary number Fuel and allows for any modes of operation of the motor to maintain proper pressure in the system. Pollution, settlement during operation on the filter element, to get into the nozzles and the ramp can not physically - all dirt remains inside the device case. While the filter element saves the ability to drive through itself the motor of fuel, no real testimony to its replacement exists.

The following symptoms are indicated to replace:

Motor does not enter the limit modes of operation (not unwinding to high revolutions, loses power);

The car is twitching when moving (there are permission in the supply of fuel);

The engine runs uneven ("Troit");

Increases fuel consumption;

The car is badly started or stalls without visible reasons.

It should be noted that all the listed features are often due to completely different problems that are not associated with the fuel filter, therefore, without additional diagnostics, they should also be considered 100% indications to replace this "consumator".

What is the danger of replacement

From remote filtering elements, manufacturers have refused not just like that, not at all from the thirst for profit, as some car enthusiasts are naive.

It's all about the imperfection of the design of the remote fuel filter. In most cases, this "consumption" is placed under the bottom of the car, in the most dirty and vulnerable placesubject to abundant baths from sand, snow and other farewell roads. Podcast space Also to "sterile", to put it mildly, does not apply. Even in the case of almost the perfect cleaning of the supply hoses and connections, immediately before replacing the filter, small particles of dirt and grains are sticking to the surface of the surface and are inside the hoses, after which they are entered into fuel injectors and forget their nozzles. It is then that the maximum damage of the injection system is applied. Ultimately, it leads to "Troy", power loss, and then to washing or a complete replacement of fuel injectors. And the more often the filter replacement is carried out, there are more of all sorts of contaminants. In particular, if the car service does not have too neat wizards (as a rule, they do not bother to wipe the dirt before replacing).

For correct replacement of the fuel filter, the driver should clearly understand the device and the functions of the element. Any type of filter or TF is designed to clean fuel from various impurities, garbage, etc. Pure fuel - stable work Engine.

Why filter clogs

ATTENTION! Found a completely simple way to reduce fuel consumption! Do not believe? Auto mechanic with 15 years old also did not believe, until he tried. And now it saves 35,000 rubles per year in gasoline!

Gasoline and diesel fuel are pure liquids a priori. They should not be present neither dust nor dirt, no resin or water. Trash appears often due to chemical reactionoccurring inside fuel tank.

It is necessary to change TF, otherwise the resin and other impurities will fall into the engine, it will begin to destroy it from the inside, the performance will decrease and the power will fall. Condensates will cause the development of corrosive processes, which sooner or later will lead to the output of the DVS. Water in the system is especially dangerous in winter - it contributes to the formation of traffic jams and permafrost in the fuel line, which prevents the supply of diesel fuel or gasoline into the cylinders.

Replace frequency

The timeliness of the replacement is important. It allows you to avoid interruptions in the work of the engine. To determine the required replacement frequency, a number of factors are taken into account: the duration of the operation of the car, activity, brand of the machine, the quality of fuel and much more.

So, the owners of the auto domestic production is recommended to change TF every 15-20 thousand km of mileage. However, in practice, the owners of the VAZ, gas, Izh rarely follow this rule, trying to save funds. As a result, it leads to even greater costs, as it turns around overhaul Engine.

A few more words about Russian fuel. It rarely complies with the factory standards, as it contains a lot of heavy metals and precipitation. The engine on such a thing is not lasting for a long time, and TF and suppressed. Therefore, if the refueling is carried out often on unverified gas stations, the filter must be checked more often than usual.

It is noteworthy that the effectiveness of the functioning of TF also affects the use of spark plugs and accelerators. Poorly treated fuel is poorly burning, the particles of Gary are settled on candles, pistons, cylinders of the power unit. The exhaust is contaminated, the accelerators come into disrepair. For this reason, along with the replacement of the filter, candles and accelerators should be updated too.

Replacing with your own hands

The replacement is obliged to be carried out correctly, so as not to face trouble with trouble. The selection of a new element is extremely important. It is advisable to buy original devices. They will last longer, they will not ruin against the slightest clogging, will work efficiently all their time.

In addition, it is recommended to install filters of the same type as the old TF. Obviously cheap models, Chinese trash does not need to install a priori, since in addition to the lack of reliability, they can not be completely cleaned normally.

Before installing a new TF, it should be removed correctly old filter. It is necessary to do it as much as possible, taking into account the fact that the damage to the fuel attraction will delay work with the replacement.

Actions	Purpose
Determine the location of the filter	In carburetor and diesel vehicles, the element is under the hood, under the bottom or in a tank with a fuel pump (in gasoline cars).
Remove fuse fuel pump	It is necessary in order to eliminate the pressure in the fuel system of the injector.
Throw off minus terminal acb	This is done to prevent fire during the fuel filter replacement procedure.
Carefully inspect the fuel filter by car and determine the method of its fastener	Fasteners can be inlet or prom. Depending on the design of the car, either latches or bolts are used. Be sure to memorize, the fastening sequence, you can even take a picture of the installation location of the fuel filter on the mobile phone chamber. Also do not forget about the location of pads and rubber bands.
Remember the fastening sequence	This is done so as not to intimidate anything when installing a new fuel filter. You can find everything on the phone.
Wrap the rag fuel filter	The rag is needed in order not to stain your hands, since a small amount of gasoline is found out of the fuel filter.

First of all, the clamps are weakened. Should know that different brands Auto fasteners can differ constructively. Before direct dismantling, it will not be superfluous to study the mounting scheme.

After the release of TF from the clamps, it is necessary to move to the removal of the main tube. At first she discovered on the one hand - it is necessary to delay from the filter, turning the hose.

In the process of removing hoses, it is not necessary to hurry, realizing that you can damage the system, applying more efforts. Perform actions without sharp movements. After the release of the tube from one end, it is necessary to move to the removal of the filter from the second edge.

Installation is carried out according to this algorithm.

1. The edges of the new filter connected to the hoses are wiped before installation.
2. The arrow on TF should be directed towards the fuel movement.
3. First one is connected one end of the hose. You need to screw the device carefully, without too much effort. In the same manner, to wear the second end.
4. At the final stage, clamping clamps, but not very much.

The fact is that excessive tightening leads to problems in the plastic part of filters, deformations and cracks of the TF housing.

After installing the filter, you should not close the hood. Everything needs to be thoroughly check - run the motor, look at the work of TF. A few minutes of uninterrupted operation of the engine will be given the opportunity to make sure that the operation performed is correct.

Install TF with your own hands is quite simple. The main thing is to have simple tools at hand: dummage, pliers, fuel drain capacitance.

How often it is necessary to change the fuel filter is indicated in the manual to the car. In this case, it is necessary to take into account that the frequency of replacement of the specified filtering device is designed without taking into account the quality of combustible and operating conditions of the machine. Therefore, there are situations where you need to change the filtering device before the deadlines recommended by the manufacturer of the machine.

Inspection units used to filter fuel

Why change the fuel filter? The main purpose of the fuel filter is the filtering of the particles of dirt, dust from fuel, to prevent them in penetration into the fuel system of the power unit. For undime replacement The specified filtering device is possible to clog the fuel supply system and the output of the auto motor.

For engines working on gasoline, two degrees of fuel purification. Diesel motors more sensitive to quality fuel mixesTherefore, for them, as a rule, three degrees of cleaning are used. For Motors, working on Dt, in winter, filtering devices with heating are used. In the presence of paraffin particles, the heating element prevents its crystallization and protects it, thus, the system from clogging.

Discern collapsible and unintended filtering devices. In the first embodiment, when the filter exits, it is made from the working state. full replacement. In the second variant, only the filter material can be changed - it is much cheaper than installing a new filtering unit.

Masters recommend changing the fuel filtering device after 30 thousand mileage kilometers. If there is a manual to the car, then you need to take 10 thousand kilometers from the period specified by the manufacturer. This will allow to take into account the domestic road domestic roads and the quality of the fuel sold at refueling.

Machine faults indicating the need to replace the fuel filter:

• vehicle is badly started while driving force aggregate begins to "troit";
• the capacity of the car decreased;
• increased fuel consumption;
• the automatic box switches the speed not on time or does not respond at all to the engine commands;
• on small speeds, with a sharp press on the gas pedal, the car does not gain momentum at all.

Ignoring the above faults can lead to the output of the nozzles or the engine. Note, the specified symptoms may be observed at other faults: broken fuel pump or clogged air filter.

Select the filter unit correctly

Filtering device in a plastic housing for fine fuel purification

The filter parameters must comply with the requirements of the vehicle manufacturer, the deviation from the recommended indicators will deteriorate the engine and output of the fuel supply system.

When buying a device for filtering, pay attention to such characteristics:

1. Degree of filtering. For insufficient level Filtering Large particles can penetrate inside the auto motor and harm it elements - it will turn into a motor overhaul.
2. Filtering area. Insufficient area will lead to a decrease in the power of the machine, interruptions in the operation of the motor.
3. Quality of rubber seals. Poor-quality seals will allow to penetrate larger particles in the engine.
4. The system for which the device is selected:

• carburetor, degree of cleaning up to 20 microns, smaller particles will not harm the system;
• injector, implies filtering up to 10 microns;
• diesel, filtration of particles is less than 5 microns, and water from fuel is removed.

Buying a filter, specify the seller model and year of car release, it is important that the acquired device corresponds to the parameters necessary specifically by your machine. The resource of the motor and the fuel system will depend on the quality of the acquired device, so require quality certificates for the assembly of interest and do not buy products of dubious production.

Repair work

Arrogo, on the filter unit housing, indicating the direction of flow

In most gasoline cars, the fuel filter is between the fuel pump and the fuel tank, also the specified device can be built into the fuel tank. For diesel cars Characterized by a podcast arrangement (at the top of the motor) of the specified filtering device. When performing dismantling and installation work on installing a new filtering device, observe such safety measures:

• repairing the fuel system, refuse smoking;
• perform repair work On the street or in a well-ventilated room - this will avoid the accumulation of fuel vapor;
• if fuel fell on the skin, rush it with warm water with soap;
• take care, so that there is a fire extinguisher near the workplace.

Replace the fine cleaning filter having a plastic case by following the following steps:

1. Unscrew the clamps fixing the incoming and outgoing fuel supply hoses, for this use a screwdriver.
2. Turn the clamps in the direction from the filtering device.
3. Disconnect one of the hoses and quickly get it up above the filtering device. These actions will help reduce fuel loss.
4. Secure the hose dropped and remove the second one.
5. Take a new filter, look at the arrow on its enclosure, it indicates the direction of movement of the fuel mixture. Install the filter unit according to the direction, put on the hoses and clamps on the legs of the filtering device and hold them.
6. Perform the fuel swap manual or by an electric pump.
7. See whether the liquid in the places of fastening of the clamps and the filter housing proceeds.

Replacement of non-separable filters

Change of unsolved filters on different types Auto runs in the following sequence:

1. Remove the fuse fuel pump, wait until the motor stops working. Thus, the pressure in the system is reduced.
2. Remove minus storm with battery.
3. Look at the method of fastening the filtering device. If the filter is fixed to the fuel pump, remember its position so that the new filtering element is in the same way. You can use the phone with the camera to simplify the specified task. Pay attention to the installation sites of sealing rubber and gaskets.
4. Take the rag and wrap the filtering device with it, because when it is disassembling a certain amount of fuel. Disconnect the filtering element from the mounting points to do this, use a screwdriver or wrench, the selection of tools depends on the method of fastening the device. Erase escaped fuel with car elements.
5. Install the new filter on the installation site of the old filter element. Pay attention to the arrow drawn on the body of the device, it indicates the direction of the fuel mixture.
6. Perform a fuel pipeline connection (pre-check its integrity, if necessary, replace the nozzle with the new one).
7. Place the fuel pump fuse.
8. Connect the battery terminals.
9. Get the car, let the engine work for a few minutes.
10. Check if there are leaks in the places of fastening a new filtering device.

After installing a new filtering unit, the machine can start from the first time. This situation may be caused by low pressure in the system. You can solve the specified problem with an ignition for one minute, after which you can try to start the car again.

Conclusion

Change the fuel filter at home. It is necessary to comply with security measures, as well as replace the filtering device in a strictly sequence. Consider: the operation of the fuel system and the auto motor depends on the filtering unit, selected for a particular auto model. The use of inappropriate according to the characteristics of the filter element will lead to a violation of the fuel and motor supply system.

(Function (W, D, N, S, T) (w [n] \u003d w [n] ||; w [n] .push (function () (ya.context.advmanager.render ((Blockid: "Ra -136785-1 ", RENDERTO:" yandex_rtb_r-a-136785-1 ", async: true));)); t \u003d d.getelementsbytagname (" script "); s \u003d d.createElement (" script "); s .type \u003d "text / javascript"; s.src \u003d "//an.yandex.ru/system/context.js"; s.async \u003d true; t.parentnode.insertBefore (s, t);)) (this , this.document, "yandexcontextasynccallbacks");

Independent Replacing Car Fuel filter - Video

The fuel filter performs an important function in the car. Although the type of gasoline seems transparent and clean, but it can dissolve a large number of all the dirt, which will eventually settle at the bottom of the tank or on the fuel filter.

The filter is recommended after 20-40 thousand kilometers. If you do not do it, then all the dirt can get into the fuel appliance, the carburetor, to settle on the walls of the sleeves and pistons. Accordingly, you will stand a more complex and expensive process of repairing the fuel system and the entire engine.

To any model car goes detailed instructionswhere the location of the filter is indicated. It can be located both near the fuel tank and directly under the hood. Before shooting a closed filter, you need to take care that there is no pressure in the fuel system. For this you need:

• remove fuse fuel pump;
• take the car and wait until he stops working;
• remove the minus battery terminal.

After that, you can safely begin to extract the old filter. It is usually attached with two clamps or special plastic latches. It is attached to the fuel tubes with the help of fittings. Each model has its own fastening features, therefore, removing the filter, remember how it stood and which tube it was screwed to what.

On the fuel filters there is an arrow indicating which direction the fuel should flow. According to it, you need to install a new filter. Observe what a tube comes from the tank, and which leads to the gas station and to the engine. IN modern models Auto filter will simply won't be in its place if it is wrong to install it.

(Function (W, D, N, S, T) (w [n] \u003d w [n] ||; w [n] .push (function () (ya.context.advmanager.render ((Blockid: "RA -136785-3 ", Renderto:" yandex_rtb_r-a-136785-3 ", async: true));)); t \u003d d.getelementsbytagname (" script "); s \u003d d.createElement (" script "); s .type \u003d "text / javascript"; s.src \u003d "//an.yandex.ru/system/context.js"; s.async \u003d true; t.parentnode.insertBefore (s, t);)) (this , this.document, "yandexcontextasynccallbacks");

Complete to the filter must go plastic latches or clamps. Boldly throw old, because over time they weaken. Insert the fuel tubing fittings and tighten all nuts well. When the filter is installed in place, insert the pump fuse and install the minus terminal to the place.

If the engine is not started from the first time - it does not matter, it is the usual phenomenon after resetting the pressure in the fuel system. He will definitely start after several attempts. Check the integrity of the attachments and do not leak. Do not forget to wipe everything well and remove all rags and gloves that have impregnated with fuel.

(Function (W, D, N, S, T) (w [n] \u003d w [n] ||; w [n] .push (function () (ya.context.advmanager.render ((Blockid: "RA -136785-2 ", Renderto:" yandex_rtb_r-a-136785-2 ", async: true));)); t \u003d d.getelementsbytagname (" script "); s \u003d d.createelement (" script "); s .type \u003d "text / javascript"; s.src \u003d "//an.yandex.ru/system/context.js"; s.async \u003d true; t.parentnode.insertBefore (s, t);)) (this , this.document, "yandexcontextasynccallbacks");