The presence of a land stick on the car. The need and order of registration of a trailer device for a car

21.08.2017

One of the frequent requests has recently - whether the resolution of the traffic police is necessary for the installation of the Farkop in 201, and what to do those who have already installed - whether it is necessary to register it.

According to the responses from the traffic police control from different regions, it is possible to answer unambiguously registration in the event that the design of the car did not assume the installation of the headquart. To the joy of car enthusiasts, most of the cars are not suitable for this definition, and installing a hitch can be installed without regard to inspection officers. Registration is not needed if you follow the rules:

1. Information about whether the installation of the Farkopa was assumed to be found in the operating instructions or clarify in the dealer center;
2. Farkop purchased in a store with all the necessary certificate of conformity and passport;
3. The mounting of the headquart was made according to the instructions and the design of the machine did not undergo changes.

Where to install a hitch?

Installing a hitch can be installed in any car service if they have a certificate of conformity to provide these services. If such a certificate for some reason you cannot provide, it is better to look for another service where they will make installation according to GOST. In the case when the car is in official dealer At warranty, you can install it or also in any certified autotech center. In this case, the warranty remains valid.

Grounds for fine

What basis may be discharged for a pantack? In accordance with Article 12.5 Administrative code Russia cannot install additional equipment on the car, entailing an increase in the danger to the participants of the movement. What is the danger in the hook without trailer? The fact is that in the event of an emergency situation, the car is not just slightly damaged by the bumper in a collision, but literally "puts on" to the hitch. Damage in this case will be much more serious.

How to avoid a fine?

To begin with, it is worth remembering that one of the penalties for this violation in 2018 is a warning. You can always try to explain to the traffic police officer and promise immediately correct the laughter and register the change in the design of the car.

In the event that the machine has already descended from the conveyor with a hitch, the penalty is not allowed to write right. Since in this case the design is provided by the manufacturer and the hitch is not additional equipment. That's just prove it, unfortunately, it is not always possible. And if the penalty is still discharged, it will have to pay for it, and in the future it is to write a statement to local traffic police to return mistakenly retained funds.

Another option - to provide an employee all required documents on the installation of a pardon. Since there are 77 points in law, according to which additional equipment specifically released for a particular car having the necessary documentation, as well as the manufacturer provided by the manufacturer, is not a violation. And, accordingly, it is not subject to imposition of a fine. That is why the hitch is worth buying factory manufacture and specialized for your brand of cars. For example, in the Okay Auto store, have all the necessary documents and are made according to technical requirements Under the specific brand of the car.

Well, the last opportunity to avoid a fine - install a removable hitch. In this case, the design will not go beyond the bumper and the traffic police officer will be difficult to explain the eligibility of a fine for such additional equipment, since it does not provide hazards for the participants in the movement.

If the hill is homekop - it is definitely subject to a fine and prescription for removal.

How much will pay

If for some reason the penalty was discharged, then it will be 500 rubles, according to Article 12.5 of the Administrative Code of Russia. The amount of the fine will be reduced by 2 times and will be 250 rubles if the payment on it will be produced within 20 days.

Farc - this is a traction coupling device (TSU) which is established on the car In order to connect the trailer to it.

The Farkop can be installed in the standards provided for it in the service center or independently, if it does not require a disruption of the machine design. That is, welding, drilling, etc. does not apply.

From 01/01/2015 began to actTelebrum "On the safety of wheeled vehicles" Tr Ts 018/2011 (hereinafter referred to as technical set). It regulates the process of making constructive changes to the structure of the car.

The installation of a headquard to such changes does not apply if the manufacturer has provided space for its fastening and made it in the list additional equipment For this model of the car.

In the absence of TSU data in approval of the TC type (FTS) and the documentation of the manufacturer's enterprise, its installation will be a change in the design of the machine. In this case, the permission to install it gives traffic police. This is evidenced by paragraph 7.18 traffic police and the law "On Security road»№ 196-FZ dated 10.12.1995.

Important. If the car is not operated, no one has the right to finish the owner for his re-equipment.

When operating the machine with a traction coupling device (TSS), you need to have the following paper:

1. Passport (Installation Instructions) Farkop with a car service mark about its mounting.

2. A copy of the certificate of TSS.

3. Act of the work done.

Does the registration of a headquart in the traffic police need: new rules for installing a pans on a passenger car

Many drivers are concerned about the question:how to legally install the traction device?

Register in the traffic police need any changes made to the design of the car. Installing a headquard almost on all models of auto allowed by the manufacturer. This is indicated in the instruction manual.

Mounting TSU does not apply to constructive changes vehicle.

Farcup does not need to be registered in the traffic police in the following cases:

1. TSS installation is provided by the manufacturer.

2. The Farkop has a passport and certificate of conformity.

3. The device for the trailer is established according to the instructions shown in the passport, i.e. the design of the machine is not changed.

When installing a pharg on a car, you should guide information from the operational documents on the machine. If they reflect that the TSS installed is certified for use in the composition of this car, it is not necessary to register changes.

New rules establish: TSU does not check and do not coordinate in the traffic police (paragraph 77 of the technical owner) in the following cases:

1. The hitch is designed for this car.

2. The assessment of TsSU car was made, there are confirmation documents.

3. Installation is provided by the manufacturer.

Information about whether this car Towing the trailer is indicated in itload table. It is located on the right average car rack or under the hood. It is reported on the possibility of connecting the trailer.

If the corresponding string does not contain data,farkop need to register in the traffic police .

Requires a TSU, attached by bolts or welded to the power elements of the machine, and necessary for serious traction loads.

When installing a hopper, the following rules should be followed with your own hands:

1. Select a device suitable for a particular brand and auto model.

2. Reading instructions for TSS.

3. Preparation of the necessary tools.

4. Dismantling of the bumper and its amplifier.

5. Installation of beams and brackets to body spars according to the scheme specified in the manual.

6. Fastening the peavercraft to the beam; Attaching the wiring harness to the beam with plastic cords.

7. Stretching the harness through the opening in the rear panel.

8. The electrical unit, the connector for it is on the car scheme.

9. The connection of the two pads.

10. Installing the details of the machine.

Attention! The bolts connecting the elements of TSS with the body must be carefully tightened. If the fastening places rusted, they should be treated with anticorros.

Competent installation of TSU Provide the duration of its operation, reliability in the way and trouble-free operation.

What documents are needed to register a headquart in the traffic police?

To register TSS in the traffic police and receipt of the evidence, you must first undergo technical expertise.

Stage 1. Pre-inspection in the traffic police

The car owner should visit the traffic police and write a statement to the preliminary examination of the machine design, pass into the window documents and after a certain period of the decision.

The inspection needs to submit the following papers:

1. Application of the established form (issues traffic police).

2. PTS (double-sided copy).

3. Documents on the hitch.

4. Registration certificate Passenger cars.

Stage 2. Examination after changes with safety assessment

A TSU is installed on the car.

The work should be done by a specialized center, which will issue confirmation documents: Act of work performed, application declaration, a copy of the certificate of conformity.

The owner distinguishes the car to inspection, where they check the safety of constructive changes and draw up a diagnostic card.

The techExpertizuisa conducts traffic police and is given a certificate.

To receive it, the car owner provides:

1. Map diagnostics.

2. TSA purchase agreement and other documents.

3. Certificate for a hitch.

4. Declaration from car service.

5. Statement and preliminary examination decision.

When the installation of a fleet on a passenger car is prohibited - fine size

Legislation prohibits installing a hitch to the machine if it is not specified as an additional equipment in the OTTS.

A copy of the document can be requested from the dealer center or from the car manufacturer. It receives firms producing or importing cars in the Russian Federation.

Equip the car chamberit is impossible if it is forbidden to use the trailer.

So, havingcategory "B" , Ride with a trailer legally, if its mass is not higher than the maximum mass of the equipped car. And the allowed masses of the machine and the trailer are not higher than 3.5 tons.

In other cases, or for the use of heavy trailer, it is necessary category "E" .

When examining a car with a hitch, the inspector may write a penalty if TsSU:

1. Non-standard or faulty.

2. Closes the state number or optics.

3. Installed in the location not provided by the manufacturer.

If there are problems in setting the machine for accounting due to the presence of a pardon, a written explanation of the traffic police should be asked why he imposed a ban on registration.

Based on the acquisitions obtained, you can writecomplaint addressed to the head of the traffic police .

Fine the TSU provides for Part 1 of Art. 12.5 COAP. Its size is 500 p. It can be paid with a 50% discount. This permits Art. 32.2 Administrative Code. This can be done within 20 days from the date of its discharge.

Important. Riding without registration of constructive changes, the car implies administrative responsibility and increases the danger to the life and health of road users.

Is it possible to avoid a fine for a hopper without his registration in the traffic police?

Can be avoided administrative punishment?

Prevent the deposit of the penalty for the presence of a trailer device a bus owner canin several ways:

1. First, a dialogue with the inspector should be conducted that everything will be fixed in the near future.

Ask him to restrict ourselves to the warning. The legality of this confirms Art. 12.5 COAP.

Such tactics are especially effective if the driver did not violate traffic rules over the past 6 months or year.

2. Using a removable bookkop

It is difficult to logically declare that these constructive changes will affect the likelihood and outcome of the accident.

Any reasonable inspector will take this point of view, since there is no protruding element.

3. TSU is set by the factory, or for it there are fasteners

At the same time, the hook is not a constructive change in the car.

4. Link to paragraph 77 of the technical owner

If the requirements of this document for cars are made - TSU is certified for the machine on which it is installed - it means that the traction device has passed the assessment, and it can be ride with it.

So, in the presence of a fleece, it requires a certificate of compliance with the technical model. Thanks to the certificate, the traffic police officer will not be able to finf by the car owner.

If the installation of TSS. does not provide for constructive changes of the machine, does not close the license plate You can install it yourself. Additional registration in the traffic police is not required.

In this regard, this option is also possible in practice. If the traction coupling device is already installed on the machine, and there is no documents on it and it is impossible to restore them, it may be easier, faster and cheaper to buy a new hitch with documents than to try to arrange a change in the design of the car. Documents on Farkop a passenger car In 2018, Russia operates the technical regulations of the Customs Union Tr Ts 018/2011 on the safety of wheeled vehicles. This document must correspond to vehicles and equipment installed on them. Consider paragraph 77 of Section 4 of Chapter V Technical Regulation: 77.

403 - Access is prohibited

Attention

Each car is a complex interconnection of nodes and mechanisms that are designed by the manufacturer and are provided for installation. Therefore, if you remove any provided item from the design of your car, install the parts not allowed by the documentation - it must be officially executed.

Info

Consequently, the registration of the installation of the Farkopa in the traffic police in 2018 will be mandatory if this traction coupling device (TSA) is not provided for by the technical documentation of transport. When it is not necessary to register additional equipment logical to assume that if the vehicle comes from the conveyor without a headquart, but it is provided by the manufacturer, then the registration of TsSU in the traffic police in 2018 after its installation is not mandatory.

Confirmation can be found in the same Technical Regulations Tr Ts 018/2011 in ch.4.

Does the registration of the Farkop in the traffic police need

The work should be done by a specialized center, which will issue confirmation documents: Act of work performed, application declaration, a copy of the certificate of conformity. The owner distinguishes the car to inspection, where they check the safety of constructive changes and draw up a diagnostic card.

The techExpertizuisa conducts traffic police and is given a certificate. To receive it, the car owner provides:

1. Map diagnostics.
2. TSA purchase agreement and other documents.
3. Certificate for a hitch.
4. Declaration from car service.
5. Statement and preliminary examination decision.

When the installation of a fleet on a passenger car is prohibited - the size of the fine legislation prohibits installing a hitch to the machine if it is not specified as an additional equipment in the OTTS.
A copy of the document can be requested from the dealer center or from the car manufacturer.

The requirements of the traffic police to the Farkop in 2018, TSU types and installation rules

Important

When operating the machine with a traction coupling device (TSS), you need to have the following paper:

1. Passport (Installation Instructions) Farkop with a car service mark about its mounting.
2. A copy of the certificate of TSS.
3. Act of the work done.

Does the registration of a headquart in the traffic police need: the new rules for installing a pardon on a passenger car of many drivers are concerned about the question: how to legally install the traction device? Register in the traffic police need any changes made to the design of the car. Installing a headquard almost on all models of auto allowed by the manufacturer.

This is indicated in the instruction manual. TSA installation does not apply to constructive changes in the vehicle.

Penalty for the hook on a passenger car in 2018

Therefore, it is very important, by mounting the hook, choose the industrial option, complete with whom the documents are coming, where the model of your vehicle is mentioned. In the case of self-made devices, riding with them remains unconditionally.

How much will you have to pay because we have previously indicated that the penalty in this case is represented not only possible, but also the likely the result of identifying on your car headquart, it remains only to report how much money will have to lay out money. In the first part of Article 12.5 of the administration of the Russian Federation, it was noted that for managing a machine that has certain faults or when identifying the traffic police officers sufficient to ban on its operation, the car owner will have to make a fine of 500 rubles.

In addition, as noted earlier, he can still make a warning.

What a penalty for a hopper without a trailer in 2018

• Does the registration of the Farkop in the traffic police need?
• Documents on a car of a passenger car.
• What if there are no documents on TSU?
• What if it is planned to buy a headquart?
• What if the hill is already installed?

Does the landark registration need in the traffic police in 2018? In this case, it all depends on the Parkop himself and from the documents available on it:

• If there are documents on the Farkop, the driver does not need to contact the traffic police to make changes to the registration certificate. You can simply install the hook and calmly exploit the car with a trailer.
• If there are no documents, it is impossible to restore them, then the installation of the pardon is a change in the design that should be registered in the traffic police.

Note.

The necessary documents for the Farkop will be discussed below.

Packagop on a passenger car: Installation, Registration, Fine

In this case, we are talking about the instruction manual, which is issued when buying any car. Open this document and find a section on the use of the trailer. If such a section is, then everything is in order.

• The hitch must have a manufacturer's documentation confirming that it is intended for use on the car of your model and a conformity assessment passed.

Thus, a list of necessary documents for the use of the Farkopa:

• Car operating manual.
• Documents on the hitch confirming that it is suitable for the car of the desired model.
• A certificate for a hitch confirming that it complies with the requirements of the technical regulation.

Please note the specified documents with you and make their traffic police officers you are not required. They can be stored at home.

Whether the installation of a flesh is a change in the car design

Television) in the following cases:

1. The hitch is designed for this car.
2. The assessment of TsSU car was made, there are confirmation documents.
3. Installation is provided by the manufacturer.

Information about whether the trailer towing is allowed to be allowed in its load table. It is located on the right average car rack or under the hood.
It is reported on the possibility of connecting the trailer. If the corresponding string does not contain data, the hitch must be registered in the traffic police.
Requires a TSU, attached by bolts or welded to the power elements of the machine, and necessary for serious traction loads.
Note. Some organizations offer to buy a package of documents for a hitch. I recommend to ignore such proposals, because The manufacturer's documents are only at the manufacturer itself.

If such documents are issued by another organization, they will be fake. What if it is planned to buy a headquart? If you just plan to install a traction device on the machine, you turned to this article on time. I recommend to buy a manufacturer before buying a fleshop and request the necessary documents. If the documentation is not provided, it makes sense to choose the device of another manufacturer. What if the hill is already installed? First of all, I recommend to verify that you have a certificate of conformity and a document confirming the ability to install your model on the car.

Penalty for TSS provides for Part 1 of Art. 12.5 COAP. Its size is 500 p. It can be paid with a 50% discount. This permits Art. 32.2 Administrative Code.

This can be done within 20 days from the date of its discharge. All new traffic police penalties are important in 2017. Riding without registration of constructive changes, the car implies administrative responsibility and increases the danger to the life and health of road users.

Is it possible to avoid a fine for a hopper without his registration in the traffic police? Is it possible to avoid administrative punishment? To prevent the penalty for the presence of a trailer device, the car owner can be in several ways: 1. First, a dialogue should be conducted with an inspector that in the near future everything will be fixed to ask him to restrict ourselves to the warning. The legality of this confirms Art. 12.5 COAP.

Question: I was frightened by a neighbor on the garage that now the workers of the traffic police will be fined for the hinge, and that now it needs to register. Is it true?

Hello, dear car enthusiasts! Yes, really recently rose hype on this issue. Let's figure out whether the registration of the Farkop in the traffic police is actually?

For the first time, we were asked this question after June 1, 2016. To be honest, at that time we ourselves did not know the answer and therefore appealed for clarifications to the District Department of the traffic police.

Question inspector

On our question, deputy. The boss of the department replied that really many people are interested in this law. According to the new rules, making changes to the car design should be registered. But there is a list of changes in the design that does not require harmonization in the traffic police. And here it is TsSU and there is in this list. But again, there is one "but".

The design of the passenger car should assume the installation in the future of this device. In other words, the manufacturer of the car structurally calculated that the car was installed on this car. According to statistics, almost 99% of cars is possible installation of TSS.

Optionally, you can document the changes in the traffic police. After that, entry is recorded in special marks in Tehtalon and PTS.

What you need to have

You can do without traffic police. There is a list technical changesAssembly, which do not require coordination with the traffic police. In order not to be discharged a fine or, God forbid, did not stop the registration of the vehicle, you should add to the usual set of documents:

• Compliance (copy) and passport on the hitch, which comes with a hitch. In the passport there should be a print of the auto center performing
• Documents provided by the Auto Center with certification to fulfill this type of activity. You are given a copy of the autocentre certificate, certified by the "live" printing, and the act of work performed.

That is, actually the hitch must be made and tested at the factory for a specific car model. It should receive a certificate of conformity, a copy of which is provided during the sale. And the hill must be installed on all regulations with a legal entity, which has a corresponding permission to conduct data.

Look below a very informative video to make changes to the design. There are talking about different additional equipment, bumpers, about gas-plane equipment, which must be made mandatory. About the landkop asked a question for 16 minutes.

How to be the one who has already installed a hitch

It is necessary to find such a certified car center that will agree to the diagnosis of your car, more precisely TSU. Looks like technical condition, the possibility of further operation. Next, the manufacturer is defined and the request is sent. With a positive response, a passport is issued to the hitch, if it was not, the certificate of conformity, the act of work performed and a certified copy of the auto center certificate.

How much opium for the people

How much does certification cost? Naturally, this procedure takes a certain time for requests and paperwork. Autocentre, generating diagnostics carry certain labor costs. The cost of this service in our installation center is 1500 rubles. When installing your new headquart, the cost of 1000 rubles. And when installing our headquart document package is issued free.

Is it possible to put on everything? How to find out?

Most cars are allowed to install TSU by the manufacturer. But there are models to which the plant did not give recommendations in order to use them as a tractor for the trailer. You can find out if you can iron horse Set the coupling device by looking at the nameplate with the wine code on your car. They are usually located on the middle right door of the door or under the hood. Consider on the example of the Renault Sandero plate.
Pay attention to numbers with kilograms at the end. In this case, they are 4.

• 4. Indicates full mass Auto. That is, the mass of the exhaust car plus the allowable weight of the cargo or passengers;
• 5. Indicates permissible mass Together with the trailer. Here I think it is not necessary to explain;
• 6. And 7. These are the masses of the maximum load on the front and rear axle.

It follows from this that if there is a mass designation with a trailer in your tablet, then the auto installation of the headquart is provided. And if there is no digit, then the coupling device is not provided.

How to be if the installation is not provided by the plant?

The question is, the question ... And in this case there is a way out. If we are talking about changing the car, you can bind with the help of an examination. Now in order.

• First, you still have to do everything that they read above. Either install or receive documents from the legalized installation center.
• It is necessary to undergo an examination in the traffic police. There you will need documents that give out autocentre and documents for the car.
• In TCP and Tehtalon will make notes about making changes to the design.

* The traffic police itself does not conduct any examination, but gives out the blanks of the documents and sends it to the address.

What punishment?

In some regions, it was seriously started to finish the owners of the car for the illegal pallkop. The penalty goes under article 12.5 COAP part 1 in the amount of 500 rubles. If you are punished for the first time in TSU (it can also be that you did not know) The same article provides for the prevention. Be polite with the inspector and tell me that they all correct. In this case, you may have to avoid punishment. But you should not delay with legalization, if you really need a hitch. If not needed, just remove it and do not look for yourself adventures in one place)))

And what about 2019?

Installing a hook on a passenger car easily. It is enough to navigate in the traction capabilities of your car. Know the characteristics of the strength of the car body, spar and the elements of the headquart. To understand the question of the Farkopa - what it is in the car, it is necessary with some definitions.

Pack car

Classification

The hook is a trailer device for attaching, fixing and further movement of the car trailer. Modern classification implies the following types of TSS:

• small
• middle
• large

It all depends on the mass of cargo, which drags the car behind itself. It is unlikely that the headscop will be "cozy" if the mass of the trailer exceeds the mass of the car. For small buses and SUVs with full Rama (spar) are installed large headquarters. They allow you to trailer not only bars trailers, but also transportation platforms intended for the carriage of boats, snowmobiles, motor equipment. Such headquarks can be found on agrotechnology: dump trucks, tractors. Bulldozers with large trailing devices withsting the maximum load. It is not necessary to overload the trailer if a large hitch is installed, above 3.5 tons.

Cars, type of crossovers, are equipped with medium parchments. Countryside is more fruitful if there is a mini trailer behind his back. A journey to the lake in the presence of an water bike involves its transportation. Large trailer functional. In this case, it is also necessary to think about any kind of medium pharg to 2.5 tons of payload.

Hard bar to 1.5 tons are installed on passenger cars. There are many types for passenger cars. Features most of them are determined no longer with the ceiling of mass, since not a reasonable load can fail the trailed, which is worse - the engine or box, and the types of fastening to the body, the spar (frame), the engineering of the material.

Constructive features

The simplest trailer device for the trailer of the passenger car is uncomfortable in the design:

Farc design

The visible part is a metal bowl at the end of the hook. Diameter - 50 mm. This is the standard. Output to connect the trailer electrician. If the lack of a bumper (damage or other reason) is visible, the main horizontal beam of the headquarter will be visible.
Invisible part - fastening to the car body. From the competent attachment of the brackets will depend on the vibration resistance of the headquart.
Hardkop on bolts can be removed for any technical work On the observation pit. It can be replaced with serious damage or failure. Eating a pardon is convenient when installing electrical reasons suitable for the trailer when it is necessary to determine the most practical distance to the plugs. The minus will be the spinning of the construction bolts while driving. Increases the risk of an accident on the road. The use of high-quality arrhythosa and strong tightening of nuts will exclude such a problem.

The welded design involves the release from the factory. It is convenient because it has a very symmetrical location and the factory execution of electric tracts running in parallel. It remains to hope for the good faith of the manufacturer. Check welding seams for the presence of microcracks and rust.

Types of fastening hook to the platform

Types of execution of homemade hoppers die on old cars. Mechanics and drivers themselves searched for the attachment points, creating unique traction coupling devices. The factory has a fastener platform or beam. To speak more precisely, the hook is attached to the platform in several ways.

The simplest compound, indefinite - the hook, connected to the welding frame. As mentioned above prerequisite Reliability will be the quality of this welding. The car owner, accustomed to save, should not be entitled when the precious garage space will be intelligent for those conditions with a sticking ball, constantly supporting anything at the rear wall, for example, fuel canisters.
Many drivers will prefer the conditionally disconnected mount to the body. But it is unlikely to deal with the screwing-reveaching of the headquart. This requires good reasons. But he can double-check the grew-washers and tightening nuts before a long trip, securing calmness.
Fully connector compounding of the Farkop choose those who rarely use the trailer. Such a hook is equipped with a shut-off mechanism. If you wish, it can be easily dismantled. The ball itself can be removed or a single hook, which goes down under the bumper or translated into a vertical position. Pay attention to the wear of the locking device, in self-made models Having a single circulation.

How to choose a hopper

Not perfect solutionWhich hitch is better, but you need to choose and acquire it for a certain brand and car model.
Frequent use significantly affects the price. Although, if single cases of exploitation are needed, you can buy more expensive removable headquarters.
For a car without a frame, a hook from the hook and the plate will not fit. It must be considered. Frame can do the minimum elements. Everything has provided a manufacturer.
The trailer should be less than the mass of the machine, respectively, this is one of the three charts of the Facts. The load table of the machine under the hood will provide the necessary information.
It is necessary to take into account the presence of elements under the trailer electrician.
Warranty and instructions, how to install a hitch, must be included.
From the point of view of Russian legislation, the pork is a traction coupling device (TSA), installed on the car in order to connect the trailer to it. Independent re-equipment of the vehicle is recognized as a violation of the TC security techniclement. If the mounting of the Farkop is performed according to the instructions, if the trailer is turned on from the factory if there is a passport and a certificate of conformity to it, then registration in the traffic police is not needed. But when operating a car with a hulkah, documents are necessary:

1. Passport Farck with a mark on the installation on the service.
2. Copy CSS certificate.
3. Act of the work done.

When independent installation, TSS should obtain permission to the traffic police. After installing the headquart, to pass the expertise in the service and get permission for the operation of the vehicle with the Farkop.

How to install a carpet on a car

The car owner chose needed Farkop. For a passenger car with a load on the body not more than 1.5 tons and wants to produce independent installation. How should the installation of the headquart on the car?

Order of installing Farkopa

Invent anything superfluous like drilling additional holes is not needed if installing the factory TSS under specific model Auto. Specifications Support 2 million load cycles. In addition, the manufacturer is responsible for the product documented. The desired set of keys will be required. Lifting or looking Yama It will not be too much.

Before mounting the beams need:

• Remove the bumper and dismantle its amplifier, if any. Difficulty is in the removal of the amplifier bolts. They zakuat. Then they need their rude extraction.
• In some cases, it is necessary to beaten the heat shield or release the silencer from the gum 20-30 cm on the stand so that it does not hang.
• Remove plugs of fastening holes in regular places on the car. Place it is pre-cleaned from pollution.
• Align the brackets with the body, install the beam, make a thorough tight of the bolts.
  Fasten the podrogue.
• Return the silencer and heat in place.
• If the bumper is not suitable for the bumper, you need to carefully finish the first.
• Return the bumper to its original position.

Montage of a headquard on a car

The rules for installing a headquart may differ, it all depends on the model or when it is still necessary to drill additional holes at the bottom of the spar. On the opposite side of the frame, the mount is mounted on a mortgage bar. This installation of the headquart will be more reliable. Significantly reduce the burden on the car body.

In the manufacture homemade device Farkopa needed a drawing of a certain design and the presence of materials for execution. The essence is to enhance the fastener on the car body using additional metal elements by type of corners, which are welded to the traverse or adjacent faces. Elements of a special platform are drilled under the appropriate fasteners. When the installation of the headquart is complete, you need to switch to the connection of the trailer electrician.

Features of electrical connection of the trailer

The main feature is the connection of electricity to the trailer. The presence of a plug and sockets suitable for each other. One end is in the trunk, the other on the trailer. There are two types of connectors - American and European. At the first 13 contacts, and the second 8. If such complexity arose, the socket and the plug need a coordination unit. About how to connect the coordination unit is described in more detail in this article. After installing the trailed you need to test with the load, check the switching light and dimensions

• Homemade TSU is desirable to perform from a good metal.
• You should not welcome the hook directly to the spar (frame).
• Select the desired drilling rolled and perform it symmetrically.
• Be prepared for a speculative concept How to install a hitch is real.

But in practice, the lack of experience is replenished with good tips from motorists with experience and friendly mechanics of services. Factory TSU, past strength tests and tests, is more reliable and safer, unlike homemade structures.