Autoshem schemes for cars. Useful homemade for car: photo and video

A selection of original and interesting schemechnical solutions and improvements for various types of car.

Car charger machine - The diagram includes a charging battery when the voltage is reduced to a certain level and turns off when the maximum is reached.
Car Charger on LM7815 Integral Microcircuit - The basis of the scheme is the LM7815 integral chip with the protection system and chains of analog indicators. Voltmeter and ammeter added to the scheme as indicators provide current control and voltage during the battery charge.
Voltage polarity switch For a charger - is designed to charge twelve toll car batteries. His main feature is that it allows connecting the battery, with any polarity.
Automatic charger For automotive lead acid batteries
Charger for powerful car batteries - Based on the IR2153 chip, this is a self-activated half-time driver, which is quite commonly used in industrial ballasts for daylight lamps

Engine overheating sensor. In order not to expect the moment when the water in the radiator will turn into steam, you can use the design on the thermostat DS1821
Sensor of ice As soon as the air temperature drops to 4 degrees Celsius, the LED fixed on instrument shield The car will flash, with further decrease in temperature, the LED flashes with a higher frequency. And if the temperature drops to - 1 degree or lower, the LED will burn constantly up to - 6 degrees, and then the device is automatically turned off.
Safety belt sensor If you ride with unsecured security belts, you can get injuries for an accident, or run into a fine. In the Arsenal of the Radio, there are special developments that signal the driver that the belt is not fastened
Water Level Signal Control. The device signals the reduction of water levels, which will inevitably lead to overheating of the motor.
Voltage indicator in car on-board network On most cars there is no device, according to the testimony of which the driver could judge the voltage of the on-board network. The voltage of the car network changes wide limits, depending on the operation mode of the power supply system.
Diagram of pre-warning drivers status As you know, up to 25-30% of the transport accidents are due to the falling asleep drivers driving. To estimate the psycho-physiological state of the driver in the management process vehicle Telemetric systems controlling the frequency of the flashing of its eyelids, the registration of the biopotential, leather-harbor reaction, motor activity. All of the above methods have not been widely used in practice due to their complexity, high cost, the need to fix on the skin cover of the driver of various sensors

Radiate selection on the topic Lighting in the cabin of the car, as well as homemade designs from the backlight rear number Before replacing light bulbs in the instrument shield: rotator repeater on LEDs, automatic anti-quilting lantern, Middle Light Schemes, structures and fixtures for headlights, Stop signal, its destination and refinement, the delay scheme for switching on and off light in the car, Running lights Scheme automatic control on a microcontroller, etc.

Making a neutral sensor. Many motorists know that car alarm with auto start on a car with mechanical box The gear is installed quite difficult, and switches the alarm to the "Automatic" mode, you can get an unpleasant result. But to solve these problems you can make the operation of the autorun more securely installing the neutral sensor from Herkeon. Recall that autorun with a manual transmission logical neutral car taking to the alarm and blocking doors can only be carried out with a motor and raised handbrake. If these conditions are not executed, the autorun is not possible.
Simulator anti-theft device Mimics the engine malfunction of your car
Remote anti-theft device on infrared rays. The schemes of remote security devices for the car on the IR rays are considered, in which the information encoding isps
Recommendations for the installation of auto alarms What can be done to prevent car hijacking? Of course, put the anti-theft system. Currently, there are many different types of signaling devices. Many firms and installation stations can offer a car owner. A number of ways to protect the car from the hijacking. Good alarm is not a guarantee of complete safety. It is also necessary to competent, and sometimes a non-standard signaling setting. A qualified installer knows the most common methods used by hijackers, and uses these knowledge when installing
Simple starter blocking scheme It consists of only one resistor and optocoupler.
Simple of simple bicycling anti-theft system This design for the bicycle will work, it is worth changing its position, or if you touch it. An alarm sound signal lasts 30 seconds, and after a few seconds, repeatedly, and so until the bike anti-theft device is disabled.
Wireless auto alarm - blocks the car engine using any mobile phone or smartphone

Articles on the manufacture of tools and fixtures for maintenance and repair of cars and their main nodes do it yourself: maintenance of car batteries; schemes of stroboscope-tachometers; The thickness gauge of the paint coatings of cars; Homemade tread cutter regulator and other original designs.

We offer the attention of radio amateurs a scheme of the electronic disabling "Mass", which does not have mechanical contacts and therefore more reliable and durable. In addition, this device can be used as anti-theft.

Auto schemes. Parktronic on a digital microcircuit

Parktronic is a special auxiliary device that gives additional convenience, especially a novice motorist, when parking, thanks to the calculation of the distance to the nearest obstacles and signaling the approximation with sound and visual signs. All parking sensors work as radar, ie emit ultrasonic waves with special ultrasound sensors and analyzed the beep reflected from obstacles

In the yard of the 21st century, and car speedometers in most cars are still analog, processing signals coming from a conventional speed sensor. Let's correct this misunderstanding, Nav to help, simple speedometer scheme on a microcontroller for making with your own hands

Of course, this is not a professional device, but also its modest features will allow to identify the degree of alcohol concentration for the driver self-control to prevent trouble on the road.

I think every car enthusiast will not refuse to have an additional service connector in a car adapted to USB or MiniUSB. Such adapters will be outlined in many situations, for example, PC peripherals, charging mobile phones Or smartphones, video recorders of events, and everything that feeds from the USB bus.

Motion sensors (DD) can be used not only for direct purpose to turn on light or as an element of security alarm, but also in cars. For example, it will scare the cat that decided to warm up at the consumer of your car, thereby keeps her life, and you will save you from cleaning your engine from the remnants of the poor animal. After all, infrared DD will react to any moving biological object having a "thermal" background.

In the car there are a lot of nodes to control the inclusion and the serviceability of which is quite difficult, and for these purposes, the sound signaling device is perfect, in addition to its use during movement reverse informs the surrounding pedestrians and other drivers about the movement of the vehicle back, which is especially important for large trucks

I propose to your court, familiarize yourself with the simple car closer convection scheme. It serves as lifting glass at the moment when the car is placed on the security alarm. Stopping the hardware device is carried out as a result of increasing the flowing current in the load at the time of the full raising of the glasses.

Automotive electrical displacement device, principle of operation and repair. As an example, we will consider the device and the principle of operation of the submersible electrical displacement of the 0580254 series of the company Bosch which is used in all modifications of the fuel injection system "K-JEFRONIC"

Car alarm It is intended for imitation of automotive beep, and made on composite transistors and thyristors

Many have portable receivers and tape recorders with a 9-volt battery type Crown. On the road, they are convenient to feed from the battery of the car, without spending the resource of expensive batteries. It is impossible to connect such radio equipment directly to the battery, since its voltage can vary from 10 to 15 V. In addition, when the engine running in the on-board network of the car appears impulse interference

Selection of simple schemes for motorists : Antison sound signaling device, ice warning devices, Cartizer gas cleaning, Device for quickly launch Engine in any frost, compressometer, anti-radar, Aerodynamic nozzle on the exhaust pipe And other designs

Collection of electric hammers on cars a very large selection.

The following schemes on microcontrollers are displayed on a two-digit digital indicator with a total anade of testimony from the fuel sensor to 40l. Food of structures is carried out from the onboard network of the car. The native car sensor in the tank is connected to the input "IN".

Probably all drivers at least once forgot to disable turn signs after maneuver? Statery clicks from the front panel are not always well audible, especially if the music is played in the cabin, so I suggest complement your car with a simple circuit signal signaling diagram with your own hands.

The cigarette lighter is one of the few car chips, which for all the time of its appearance has been retaining its first initial design for over 70 years. As a result, both at rare cars, and on the most modern models The same design is used. Of course, in ancient, this device was used only for the sake of one function, although Saita in the modern "information world" - it performs different functions, allow the connector to charge various digital gadgets or even starting the machine.

Radio Digital Radio Schemes We are designed to work only with LEDs in the stop signals of your car, if you still use conventional light bulbs, you can easily repeat the design of the turning on the turning on the turning on the turning. Simple development " Stop signals"- a homemade time relay will turn off the latter if they are burning over 40-60 seconds, and modernization of turn relay 495.3747 will allow you to enter standard complete set VAZ or gas LEDs instead of incandescent lamps.

The proposed first version of the engine wiper relay has more high reliability Work, can provide dynamic engine braking. No alterations of a regular electrical equipment circuit is not required. Quite simple options for upgrading the wiper relay will allow you to not be distracted by turning on and off janitors. In addition, many old cars have a simple velocity regulator of the engine wiper engine - for two positions "quickly slow" - not a big refinement is simply necessary. And set the humidity sensor and the water drops that the scheme will start themselves.

Monitor for a car with rear view cameras important element In your car, because in modern urban reality, you need to be a parking master to find a place where to park the car. An example is clearly indicated by installing a monitor into a car visor, which makes an image that is optimally located for the driver's eye.

Nowadays, more than ever, there is a question of accounting and saving energy resources, including fuel for vehicles. Of the greater diversity of devices that take into account fuel consumption, devices with a registering element of the sensor in the form of an impeller received the greatest distribution. Sensors with a different measurement principle, although they have sufficient accuracy, but are complex in manufacturing and have drawbacks. Practice has shown that sensors with an impeller made with the necessary and sufficient accuracy can work for years, not requiring care, with an error in registration below the tolerance for such type of instruments

The ignition system is a combination of various automotive devices and devices that ensure the generation of electrical sparks to ignite the fuel and air mixture in the engine cylinders internal combustion At the moment of rotation of the key of the ignition system. On this page you can find various schemes for connecting VAZ car ignition. And homemade radio amateur options for electronic ignition scheme

It has the following advantages: the power of the spark is increased, the contacts of the interrupter do not overtake; Does not need a resistor in the chain of the ignition coil; when the ignition is on, but the engine unused the scheme smoothly without spark, turns off

In the Soviet Auto industry, the RS57 type rotation indicator circuit breaker was the electromagnetic principle of operation and was used to ensure the flashing of signal lamps, which makes it more visible and noticeable to supply the signal signal to other participants in the movement. The rotation indicator breaker is turned on sequentially into the signal lamps chain signaling the turn. As part of the article, we consider the options for replacing this electromagnetic device to its electronic analogs.

Probably, every car enthusiast forgot in the warm season, close the windows in the car, so that it no longer occurred, I propose to collect a scheme intended for the automatic closure of all windows in the cabin of the machine when setting to the alarm. Consider several possible options Implementation of the design from simple schemes with a relay, to the power windows control machine on the microcontroller.

Each driver of a cargo car or bus with a voltage of the on-board network at 24 Volta faced with a problem, connecting the consumer of 12 volts. This article implements a solution to this problem.

In all modern cars, when the engine temperature approaches the critical mark, the radiator cooling fan is triggered. But there is a mass of negative effects of a sharp start, which over time affects the electrician vehicles. This article describes the scheme for replacing the cooling relay switching on the cooling fan.

Economy meser carburetor

Carburetors, long years have been settled by car, until they gradually dismissed their place to various fuel injection systems. But the automotive century russian cars Long, and still have to deal with vehicles in which there is still a carburetor. Well, as it is known, its normal work is provided with non-technically devices, among them the main fuel economizer. It is about him that we will talk, as well as consider the scheme of the coercive economizer system idle move For cars VAZ

The automotive starter is a device that ensures the start of the engine after turning under any weather circumstances. Almost all starters are inherently conventional short-term electric motors, but high power. The starting cycle of the standard device consists of three attempts with a 30 second interval between them. Since the car has a single source of electricity (rechargeable battery), then the engineers have chosen a DC electric motor for starters.

Each car owner, who was sitting behind the wheel of a budget car knows how long you have to expect the receipt of heat from the engine when he warmed it in the winter season, especially if you live in the northern part of the most big countries World. The set time of a comfortable temperature is somewhere 30 minutes, and so every morning. The best idea of \u200b\u200bsolving this problem in my opinion is the heating of the car with a fan heater. Imaging the idea of \u200b\u200blife, helped the old toaster and a faulty computer power supply.

In winter, many Russian drivers begin the time when a pre-warmed engine is required for a trip to the car. Solving this problem helps the car heating scheme of the car. The first considered sufficiently simple to repetition.

Heated steering wheel, along with heating seats, mirrors, stalk, it is not a luxury today, but the indicator of the fact that a person lives in a civilized country. All the listed parameters in the personal car are very convenient, and help the driver focus only on the control of the vehicle, and not on its free fingers.

This design is designed to generate a beep when moving trucks And buses back, while automatically starts to generate a beep warning of danger.

The main advantage of the second battery is that the consumption of accumulated energy occurs through an additional battery, and the first is in stock, that is, you can not worry about the car's plant after the picnic in Dali from civilization. Many foreign cars already have a second rechargeable battery under the hood. The lack of them consists only in parallel connection of 2 acb

This amateur design is suitable for charging most of the smartphones and tablets from 5 volts, even when the ignition is turned off. Or will power the DVR for 40 minutes, at that moment when the car is waiting for its master in the parking lot. The basis of the scheme of the microcontroller AVR TINY13, the firmware is knocked out.

Electronic homemakers, today, are an affordable way to manufacture useful mechanisms capable of facilitating life and diversify leisure. Modern craftsmen are capable of collecting both simple toys and complex, multitasking mechanisms. About how easy and quickly make electronic toys, interesting and useful electronic homemakers for home and car do it yourself - read below!

Simple electronics with your own hands: do spinner

Electrical engineering, today, is used everywhere to implement both practical and entertainment purposes. Some inventions (such as a smart home system) make a newcomer quite difficult. They require experience and in-depth knowledge of physics. Other designs are simple and accessible to beginner radio amateurs. So, for example, you can make interesting toys with your own hands - spinners whose sales incredibly increased this year.

To collect the toy you will need to stock:

• Wooden billet size 9x4x1.2 cm;
• Bearing of 2.2x0.8x0.7 cm (with a rubber seal);
• Two RGB LEDs;
• Two batteries and CR2032 holders;
• Bolt from stainless steel 0.8x2 cm;
• Cap nuts M8.

After that, you can proceed to work. First of all, it will be necessary to find a design scheme on the Internet, and transfer it to the untreated bar - the workpiece. In order to properly outline the technological holes (there are three of them) it will take a ruler.

After that:

1. In the middle of the workpiece drill through hole diameter 2.2 cm under the bearing;
2. Drill on the sides of the billet two holes with a diameter of 2.5 cm and a depth of 7.5 mm;
3. Using the drill to do in the middle of two non-current two holes with a diameter of 6 mm for LEDs;
4. Treat the holes of the zenkovka;
5. Give the toy rounded shape using an electrolovka, a ribbon saw or a logging machine;
6. Sanding the workpiece with sandpaper, and cover it with varnish;
7. Soldering LEDs to batteries;
8. Check the LEDs and install them into the seating holes by fixing on super-glue;
9. Clear bearing, and process its insides WD 40;
10. Cut off the bolt cap, and fasten the axis in the bearing on both sides with nuts;
11. Install the bearing into the seating hole.

Spinner is ready! The toy will be interesting not only for children. Adults will be able to use such an electronic: the device, rotating, will help relax or distract.

Uncomplicated electronic homemade schemes: Making an electric lion

It is enough simple and quickly with your own hands you can make an electric-connector.

Such a call will last long and will delight the ear. After all, when you click, it will be able to create signals of various frequencies and tonality.

Thus, the electro-call can be one-photon and multi-torrent.

On the ability of a call to reproduce the sound in one or more tonalities will influence the presence in the multivibrator radioconstruction scheme with two bipolar transistors. Consider the details of the electronic call scheme with a complex sound signal.

Thus, the electronic homemade scheme will consist of such radio components:

• Lowering transformer series TA;
• Ring buttons;
• Five alloy silicon diodes;
• Electrolytic capacitor with a capacity of 1000 microfrades
• Two electrolytic capacitors with a capacity of 10 microfrades;
• Two stroke resistors with resistance in 470 kiloma;
• Two mlts of resistors with a resistance of 10 kiloma;
• Two mlts of resistors with resistance 33 kiloma;
• Resistor MLT on 1 kilome;
• Resistor mlt at 470 kiloma;
• Three silicon-plenary transistors type 630d
• Silicon-planar transistor type 630g.

The principle of operation of the device is simple. Pressing the button will open the third transistor of type 630d, giving the current to the fourth transistor of type 630g. This will create a primary signal. When opening a second transistor of type 630d, the third and fourth transistors will turn, creating a signal of another tonality.

Homemade do it yourself for the car

Autoelectronics, for today, has a huge demand. At the same time, homemade automation, often, has simple schemes, Easy performance and installation. What electrical sequels can be done on your own car?

So, with your own hands for the car you can do:

• Dynamic turn signals using Kit DIY constructor;
• Universal charger from old electronics;
• Air conditioning based on water pump;
• Withers with heating and much more.

The easiest way will be constructed backlight for safety belt locks. To do this, it will be necessary to dismantle, and disassemble the locks using a flat screwdriver. After that, with the help of a thermal stake in the locks, it is necessary to secure LEDs.

Each LED can be included through its current-limiting resistor: it will prolong the service life of the semiconductor light-emitting device.

After that, you should collect locks, and the wires that feed the LEDs, stretching under the seats to the ignition or the dimensions button through the cigarette lighter. At the request of the owner, the car lighting of the cabin can be supplemented with lamps that signal that the seat belt is not fastened.

Unusual electronic homemakes: binary watch with their own hands

You can make funny binary watches for your own hands. To do this, you need Arduino Platform. Electroschemes on this platform are characterized by simplicity and convenience, used for the manufacture of most electronic homemakes.

In addition, you will need a binary watch:

• Real-time clock module on the DS1302 chip;
• Diffuse LEDs with a diameter of 1 cm (20 pieces);
• Resistors with resistance of 10 ohms (20 pieces);
• Resistors with resistance in 10 kiloma (2 pieces);
• Two clock buttons;
• Case.

The case of the clock should consist of two halves, which can be made of wood, plastic, metal. It depends on what style will be your watch. Before making the case, you will need to assemble the LED matrix.

At the same time, each LED must be connected through its current-limiting resistor.

After that, the conclusions from the LEDs must be connected to the platform. The controller itself will need to connect to the real-time clock module. After that, contacts from Arduino and the module must be carried out to the clock buttons to adjust the time through the resistors with a par value of 10 kilomes. They will serve as loads. Under the end, you should connect the power cable to the diagram.

Useful homemakes with their own hands: How household scales are made

Today, in almost every house there are outdoor or kitchen scales. In order to independently make this useful measuring instrument, it is necessary to deal with its device and the principle of work.

So, to the external components of the scales include:

• Web processor;
• Housing;
• Screen for readings;
• Platform;
• Legs.

The principle of operation of the scales is extremely simple. The load, falling on the platform, presses on it due to gravity, activating the strain gauge weight sensor inside the instrument. The strain gauge, in turn, affects the tesorressor, changing his resistance. The latter transmits a signal to an analog-to-digital converter. After that, the ADC translates the signal into digital and serves it on the microcontroller, which makes conclusions about the mass of the load on the platform, and displays the values \u200b\u200bto the screen.

When assembling the scheme, you must pay attention to the type of strain gauge sensor.

So, for the central location under the platform of outdoor, trading and technical scales It is better to choose a single-point sensor. A block sensor is used to install on bending. At the same time, it is necessary to ensure that the strain gauge has a reliable connection with the ADC. Solution will solve the problem of connecting devices.

Radioshames do it yourself for home: Making an electronic lock

The electrician can serve to protect the house. So, today, the sites of self-delicacies offer simple radioshes of electronic locks for the front door. Open such a lock using the physical key will not work.

The simplest electrical system for the manufacture of the lock, usually, is based on the four-digit Johnson counter.

This scheme can be implemented in several variations. The most simple - using the chip 4017. The principle of operation of the circuit is quite simple: when entering the correct code consisting of four digits, a logical unit is activated at the input of the chip, which opens the lock.

Consider the operation of the device more details:

• When you press the wrong keys, the diagram is restarted without the operation of the mechanism through the RESET entry.
• The correct signal, when you press the key, should enter the VT1 field transistor, which, after opening, supplies the output to the appropriate key;
• After the correct introduction of the correct code, from the output corresponding to the last right key, the signal is fed to the VT2 transistor connected to the relay;
• The transistor is activated for a time that determines the capacitance of the capacitor;
• The relay opens the actuator (for example, a latch).

In order to open up such a castle, you need to go through about ten thousand different codes. At the same time, the numbers on the code should not be repeated. That is, the code 3355 will be impossible, all digital values \u200b\u200bmust be different.

Most of the electronic homemakes that are manufactured by modern masters are designed to perform the usual household tasks faster and high quality authentic devices. So, for example, it will significantly speed up the process of creating an electric stroke yarn. It is possible to quickly make electrical shields by putting an electric feed on an authentic device.

At the same time, the engine for the electrokeum must have a power of at least 15 watts.

As an engine, you can use the motor from the fan, the fan, the player. To activate the engine, use the pedal. You can change the motor movement by including a TP type toggle switch to connect a condenser and resistance to different windings.

Useful, easy to assemble and operation will be an electric wobble.

In order to implement such a mechanism, you will need to collect a standard block generator. At the same time, it will be necessary not to forget to isolate the fluff stick.

Where to find amateur diagrams and homemade

Modern radio amateur websites propose not only useful, but also unusual radios models. So, for example, on the brains website, you can find interesting radio-electronic schemes for the manufacture of reminders for the refrigerator, thermometers that change the color depending on the temperature, etc.

Interesting and helpful will be electrical things for life and crafts from girlfriend for fishing from the site "Visiting Samodelkin".

On how to design, debug and make electronic mechanisms at home, you can read in the book "Entertaining Radio Electronics". NEWs among radios models often posts the website of the Radio Worker's Workshop. Employed and useful technical materials contain new issues of the magazine "Radio Piters".

Homemade with your own hands at home (video)

Radiate mugs enjoy today, popular with both schoolchildren and adults. Master classes and radioches presented on various sites make it possible to collect almost any electrical appliances at home. The main thing is to find the necessary schemes, to clearly follow the instructions, and adhere to the safety technique when working with electricity. And you can collect everything you want!

Since you decided to become a self-taught electrician, then surely after a short period of time you will want to make some kind of useful electrical appliance for the house, car or giving your own hands. At the same time, the homemade can be useful not only in everyday life, but also made for sale, for example,. In fact, the assembly process simple devices At home does not represent anything complicated. You just need to be able to read the schemes and use the tool for radio amateurs.

As for the first moment, before proceeding to the manufacture of electronic homemakes with their own hands, you need to learn to read the electrical strokes. In this case, our good helper will be.

From tools for beginner electricians, you will be useful for a soldering iron, a set of screwdrivers, pliers and a multimeter. To build some popular electrical appliances, even a welding machine may be needed, but this is a rare case. By the way, in this section of the site, we even told the same welding machine.

Separate attention should be paid to the girlfriend, from which each electrician newcomers can make elementary electronic homemakes with their own hands. Most often, old domestic parts are used in the manufacture of simple and useful electrical appliances: transformers, amplifiers, wires, etc. In most cases, novice radio amateurs and electricians are enough to search all requirements In the garage or shed in the country.

When everything is ready - the tools are assembled, parts are found and minimal knowledge is obtained, you can proceed to the assembly of amateur electronic homemade at home. This is where, our small reference book will help you. Each granted instruction includes not only detailed description Each of the stages of creating electrical appliances, but also accompanied by photo examples, schemes, as well as video lessons, in which the entire manufacturing process is clearly shown. If you do not understand some point, you can clarify it under the recording in the comments. Our experts will try to advise you in a timely manner!

If you think that homemade is the lot of kids and bored housewives, we will quickly dispel your errors. This section is completely all devoted to the manufacture of homemade from automotive spare parts and rubber tires. You can make almost everything from the auto stroke. From garde shoes to a full-fledged playground with swings, fabulous characters and elements for recreation. Finally, and eternally busy dads will appear the opportunity to show their creative talents and create something useful and beautiful on its own landed area or a rival yard.

The automotive tires should be involved in disrepair, especially considering the domestic quality of roads and sharp temperature differences. Instead of sending the old auto stroke into a landfill, it can be slightly transformed and give a new life on the playground, in the garden or garden.

We collected a huge number of examples how to make automobile selfiems Using tires in various household and aesthetic purposes. Perhaps, one of the most popular ways to apply the arrangement of its auto stroke is the arrangement of playgrounds. The easiest option is to wear up to half a row of tires and decorate their upper part in bright colors. The architectural element created in this way will be used by the kids as a device for walking and running with obstacles, as well as instead of "furniture", because on the surface of the tire you can decompose the sand products or even sit yourself, resting a quiet summer evening.

It is possible to diversify the exterior of the platform to the exterior, creating fairy-tale dragons, funny bears, who will meet your guests at the entrance to the courtyard in the garden of crocodiles and other animals. Followers of flowers, a car tire can replace a full-fledged vase, and the plants planted in her will give the courtyard well-kept views.

You can please the children by creating comfortable swings from the most surviving tires. You can leave the tire shape in the original form, and, having spent a little more time and effort, create an unusual swing in the form of horses.

Whatever you choose, to create automotive crafts, your children in any case will be delighted with the appearance of homemade for cars in the yard. Inventive children will be able to play new games, and will definitely be proud of their folder, praising your creation to friends. And the mixture of happiness and pride for you in the eyes of the child is perhaps the only thing for which you can step on the throat of the long-awaited weekend in the company of the sofa, television and beer.

Various homemade for the car has always been interested in motorists. They are all designed to improve the characteristics, appearance or comfort a passenger car. For example, you can make a subwoofer, a convenient organizer, eyelashes on headlights, license plate protection, etc. We will tell you about some useful homemakes that everyone is available.

Each motorist seeks to make your car unique. You can do this with the help of peculiar linings on the headlights that are called cilia and add a kind of highlight to the appearance of any car.

For the manufacture of cilias, you will need the following:

• construction hairdryer;
• dense paper or cardboard;
• soil and paint;
• sandpaper;
• hacksaw;
• scotch;
• plexiglas.

First you need to decide on that cilia of which form you want to get. The choice depends on your preferences and fantasies. Draw on paper or cardboard template and cut it out. On it, you can cut a piece of plexiglas in the future.

Attach the created template for the headlight of your car and give it a complete view, carefully sewed all the face. When everything is ready, attach a pattern to plexiglas and circle some sharp object. According to the resulting circuit, you should cut the part.

In order not to damage the headlights and protect them from scattering, their surface is better attached to scotch. With a hair dryer, heat the workpiece, and when it starts to bend, you can apply it to the spotlight.

After that, the surface must be treated with sandpaper, wetting it with water. When everything gets freeze, paint the part of the ground, and then paint on any suitable color. Everything is very easy, and the result can exceed all your expectations.

If on wheel disks your car appeared scratches or chips who spoiled appearance Products, you can send the wheels to painting into a specialized workshop. If you don't want to spend money on this, you can try to restore damaged places yourself.

To work you will need:

1. Scratched discs.
2. Epoxy glue of any color, as a layer of paint will be superimposed on top. However, if the paste is too bright, it can be shuning through the LCP, so before applying the paint, it is better to carefully completely pricked by primer.
3. Natural paper number 300-400 and 600.
4. Adhesive tape.
5. Caller with paint and varnish.

First, with the help of coarse-grained emers, it is necessary to clean the locations of the chips and scratches to such an extent, it was impossible to grope any bugs. We recommend the rubber to shock the adhesive tape and cover with newspapers so that the paint does not hit it.

Sleep both epoxy adhesive components in the proportion of one to one. Apply the composition on stripped scratches in such a way that the mixture completely filled them, and the thin layer was formed on top.

Care all dry. It takes a lot of time, and to speed up the process, you can use heat, placing a fan heater or a simple incandescent light bulb.

When the glue dries, clean it with shallow sandpaper, having prepared the surface under painting. Everything should be smooth to the touch and on appearance is important.

With the help of a can of paint discs completely not difficult. You need to carefully shake the cylinder and start spraying the paint from a distance of 20-30 cm. Apply the paint should be layers. Do not allow too obvious transitions, causing two or three layers. Each of them needs to be dried, waiting for half an hour. To protect fresh paint from dust, it is better to perform painting works in a pre-moist room.

After the paint dries, impose two layers of varnish. Between the layers you need to look after half an hour, and the upper layer should be dried longer.

When everything thoroughly dry, it is necessary to moisten with water with the smallest grinding paper (grain 1000-2000) and gently smooth the proclaimed area. To achieve factory shine, the surface can be polished.

The theft of registration marks today has become one of the illegal types of money for attackers. For the embezzlement of numbers from the machine, thieves require no more than 10 seconds. In order not to get to the fishing fraudsters, you need to take care of the protection of the registration number. There are several ways, each of which can be realized independently at home.

Protection of the number with Scotch

This method of protecting the license plate from theft may seem funny to you, but it is quite effective. The rear surface of the registration number should be deguted and glued to it bilateral tape. This simple and inexpensive way to protect the number creates an additional obstacle to the thief that your registration sign can save.

Secretakes for car room

Instead of simple screws that are recorded license plate, secrets are installed. Hats have such a design that you can only unscrew the secrets special keysoldered together with fasteners. There is a set of about 500 rubles, and the installation does not take away a lot of time.