How to replace the liquid in the power steering hydraulicel on the UAZ patriot with their own hands? Maintenance of GUR UAZ Hunter, replacement of the working fluid and filter GUR oil and defects.

Repair and maintenance of cars, engines and automatic transmissions

Diagnostics and adjustment of the steering mechanism UAZ-Hunter 315195, UAZ-31519

Figure 1. Steering mechanism with hydraulic cylinder GUR UAZ-HUNTER 315195, UAZ-31519

1. Nut; 2, 5, 6, 17, 21, 23, 24, 37, 40. Sealing rings; 3. Glass; 4, 11. Stubborn bearings; 7. Piston rail; 8. Screw; 9. Carter; 10, 18. Contacts; 12. Connection of the hose hose; 13. Connecting a drain hose; 14. sleeve; 15. Cuff; 16. Torque; 19. ball valve; 20. Balls; 22. Channel in the Carter; 25. Cup; 26. Task nut; 27. Protective bottom cover; 28. Stopper rings; 29. Adjusting washers; 30. Support shaft; 31. Rollers; 32. Tower rod; 33. Protective upper cover; 34. Rotor; 35. Protective cap; 36. Distributor Corps; 38. Channel in the dispenser housing; 39. Bolts fastening the camshable casing to the Carter

- Remove the steering mechanism.

- Secure the steering mechanism in the vice so that the holes for draining and draining (holes under fittings) have at the base.

- Drain the oil from the mechanism, turning the rotor 34 (Figure 1) or the coil roll manually.

- Press the rotor with your hand or the coil shaft along the axis and shake the tower 25 (see Fig. 1).

- If there is an axial offset of the rotor or the coil shaft, it is necessary
adjust the thrust of the stubborn bearings 4 and 11.

- To adjust the thrust bearings with a beard and a hammer, straighten the ball of the cup of 3, which is sealed in the groove of the crankcase wall.

- Remove the clearance by turning glass or nut clockwise.

- Check the rotor torque or coil shaft in thrust bearings, it should be 2 nm (0.2 kg / cm).

- If in the middle position of the Tsheka UAZ-315195 shaft, UAZ-31519, when you are swinging on the tank, the gap is felt, adjust the transfer by turning the nut 26 and remove the sushka.

- Remove the upper and lower 27 and 33 protective covers.

- Remove stop rings 28 and gasket 29. Loosen the lock nuts and loosen the lock bolts 26 with two or three turns.

- Align the gaskets 29.

- Rotating support supports 30 with a backshot counterclockwise (if you look from the spline of the nipple shaft), remove the gap in the engagement.

- Adjust the position in the UAZ-Hunter 315195 shaft shaft position, UAZ-31519, corresponding to the average position of the tooth sector.

- Check the torque torque, it must be within 35-45 nm (3.5-4.5 kg / cm) when passing through the middle position.

- Install the adjusting washers 29 and locking rings 28, bend one of the antennas in both adjusting washers in the groove of the tower support shaft.

- Wrap the lock bolts and locknuts 25 with a torque of 8-10 nm (0.8-1.0 kg / cm).

- Install the items in the reverse order.

- Remove the air from the steering system with the amplifier.

If the UAZ-HUNTER 315195 hydraulic amplifier, UAZ-31519 fails, as a result of damage to the pump, the destruction of the hose or drive belt pump or towing

Replacing liquid hydraulic power steering UAZ Hunter

Here we will tell you how not to kill your Gur And how to choose butter in Gur For your car.

Selection of oil in gur

Tires and discs. Price comparison (Russia): Tires and discs. Price comparison (Ukraine) :.
Due to the engine stop, you can use the steering mechanism for a short time.

In the absence of oil in the hydraulic system of the UAZ-hunter 315195, UAZ-31519, it is necessary to remove the driving belt of the pump, otherwise the pump can be stuck, and the belt may break.

When removing the pump drive belt on vehicles with ZMZ engines, the refrigerant temperature should be carefully monitored, since the engine can overheat.

The long-term operation of the car with a non-working hydraulicer leads to premature steering mechanism.

Fig.2. Steering power steering with UAZ-Hunter 345195, UAZ-31519 with engines UMP

1. Tension screw; 2-bolted fasteners; 3. Pullets of the power steering pump; 4. Drive hydraulic steering pump; 5. Shkiv crankshaft

Tension of the pump belt of the pump gas UAZ-315195, UAZ-31519 (see Fig. 2) is carried out by moving the pump along the bracket to the engine.

To do this, loosen the pump mounting bolts to the bracket, move the pump using the tension screw until the belt tension becomes normal and tighten the pump mounting bolts.

Replace the belt if it is damaged or excessively stretched.

Checking the level and change of oil hydraulic oil GUR UAZ-HUNTER 315195, UAZ-31519

When checking the oil level in the oil tank, the front wheels must be installed directly.

Add oil to the oil tank filler or no more than 5 mm above it.

The oil must be pre-filtered through a filter with the subtlety of filtration not more than 40 microns.

Fuel steering system UAZ-HUNTER 315195, UAZ-31519 in the following order:

- Disconnect the tower from the bump or hang the front wheels.

- Remove the oil tank cover, fill the oil before it appears above the filter grid (no more than 5 mm).

- Without starting the engine, turn the steering wheel or the mechanism input shaft from the stop until it stops until the air bubbles come out of the oil in the tank. Add the oil to the tank.

- Run the engine by adding oil into the tank.

- In the case of excessive foaming of the oil in the tank, which indicates air entering the system, the engine is muted and allows oil to settle for at least 20 minutes (before air bubbles leave oil).

- Inspect the plug of the hose on the UAZ-HUNTER 315195 hydraulic system nodes, UAZ-31519 and, if necessary, remove leakage.

- Give the engine to work for 15-20 seconds and pump the steering steering system with a steering force to remove residual air from the steering mechanism, turning the steering wheel from the lock until it stops, without lingering in extreme positions, three times in each direction.

- If necessary, fall oil in the tank.

- Close the tank with a lid and tighten the cover of the cover manually.

- Attach the stem, tighten and clap the ball pins.

3. Consumables and safety valves GUR UAZ-HUNTER 315195, UAZ-31519

1-spool valve of the flow valve; 2. Spring safety valve; 3. The guide springs of the safety valve; 4-ball safety valve; 5-spring spring; 6-seater safety valve; 7-filter; 8. Ring; 9-pin plug; 10-sealing gasket; 11-adjusting gasket

Maintenance of flow and safety valves GUR UAZ-HUNTER 315195, UAZ-31519

If spare and safety valves are contaminated, rinse them. To do this, follow these steps:

- Unscrew the plug 9 (Fig. 3), located above the outlet of the pump gas UAZ-Hunter 315195, UAZ-31519.

- Remove the spring 5 and fill the flow valve and insert the plug into the place to prevent oil leakage.

- Unscrew the seat of the safety valve, remove the ball 4, guide 3 and the spring 2. Remove the ring 8 and the filter 7 from the safety valve seat.

- Rinse the items and blow with compressed air.

- Collect in the reverse order. Be careful when assembling.

- When disassembling and assembling, not to break the setting of the safety valve, do not change the number of adjustment pads 11.

UAZ Patriot, known as the UAZ-3163, is produced since 2005 by Ulyanovsk Automobile Plant. This model It has four-wheel drive and big ground clearancethat gives the SUV very increased patency. UAZ Patriot has a all-metal five-door body. All-metal design provides a high margin of strength, due to which the SUV can move through any categories of roads.

Perhaps, when developing this model, the idea was taken by the UAZ-3162 "Simbir", because in the end, many elements were transferred to new model. Among these bridges "Spyser", a five-seater and nine variant of the interior design (depending on the configuration), as well as the installed power plantsthat provides the Volga Motor Plant. But completely similar car It is impossible to be called, as some significant changes have been held, which in the future gave increased patriot comfort.

In addition to domestic here, foreign elements and components are also used here: the hydraulic power steering force of the Italian production Delphi Italia Automotive S.R.L., brake system German production ContitEves, steering wheel from the German company Takata-Petri AG, heating system and air conditioning from the British manufacturer Sanden International Europe Ltd, MCPP provided the Korean manufacturer Dymos and many others.

In 2006, in UAZ, Patriot began to establish an anti-slip system of German production (Bosch). In 2008, air conditioning, as well as the heating and ventilation system, were finalized. From this year, the SUV can be used in rather hot temperature conditions, since the cooling system of the power plant, which has become more efficient, was also finalized.

In the spring of 2012, the model appeared updated dashboardAn injury-safe four-spin steering wheel from the German manufacturer Takata-Petri Agi new radio. The used radio tape recorder is equipped with a USB connector, which allows you to connect various USB media. Also, a new radio has a dimension of 2DIN.

A large number of changes had to 2013. This year, the SUV received an improved dispensing box, which provided the Korean manufacturer of Dymos. Distinctive feature This distribution is the use of electrical control instead of lever. That is why, instead of him, a special washer was placed in the cabin, through which the gear shifts dispensing box. The length of the rear cardan shaft was reduced, and an intermediate support was removed. A separate unit is located on the driver's door, which allows power windows and rear-view mirrors. Until this year inclusion parking brake implied the locking of the cardan shaft, now hand brake Blocks rear wheelsThus, the manufacturer made it more efficient. Among other elements that have received changes should be allocated handles for passadirov, the central rear view mirror, as well as the ceiling. For the first time, the "Winter Package" equipment appeared, in which the model was completed with heating windshieldindividual heating system For passengers of the rear row and heating of the rear seats.

Autumn 2014 brought new changes and refinement into the car design. First of all, the manufacturer has established improved lighting equipment, modified modified bumpers and seats, both front and rear. Many owners have particularly pleased the presence of a stabilizer transverse stabilityThanks to which the SUV began to save the balance on the road. Both cardan shafts have been replaced by more durable and not requiring frequent maintenance. Among the additional options included in the individual configuration, a multimedia system with a navigation system and a special chamber that provides rear review has been added.

2016 became the last when UAZ patriot was refined. In 2016, the SUV became completed new lattice The radiator in which the emblem was increased, which is exactly the first and striking. The gearbox lever and the dashboard were changed again and improved. The steering column was adjusted in height, and the seat belts received special pretensioners.

Types of engines and oil volume in the hydraulicel

How much to fill oils in gur - 0.94 liters

From the very beginning of the serial production of UAZ Patriot was completed with one of four engines:

1. ZMZ-51432

• The diameter of the cylinder is 94 millimeters.
• Piston move - 87 millimeters.
• Working volume - 2235 cubes.
• Peak power at the exit - 114 horsepower / 84 kilowatta (at 3500 rpm).
• Peak torque - 270 Newtons per meter (at 1800 rpm and up to 2800 rpm).

2. Iveco F1A.

• Manufacturer of the installed motor - Iveco.
• Motor type - four-cylinder diesel with inline cylinder arrangements.
• The diameter of the cylinder is 87 millimeters.
• Piston stroke - 94 millimeters.
• Working volume - 2287 cubes.
• Peak power at the output - 116 horsepower / 85 kilowatt (at 3900 rpm).
• Peak torque - 270 Newtons per meter (at 2500 rpm).
• The number of valves in the GBC is 16.
• The degree of compression in the combustion chamber is 19.
• Power system type - Common Rail.
• The type of cooling system is liquid.

3. ZMZ-409051

• Manufacturer of the motor installed - the Valvage Motor Plant.
• Piston stroke - 94 millimeters.
• Working volume - 2693 cubes.
• Peak power at the exit - 147 horsepower / 108 kilowatt (at 5000 rpm).
• Peak torque - 235 Newtons per meter (at 2650 rpm).
• The number of valves in the GBC is 16.
• The degree of compression in the combustion chamber is 9.8.
• The type of cooling system is liquid.

4. ZMZ-40906

• Manufacturer of the motor installed - the Valvage Motor Plant.
• Motor type - four-cylinder gasoline with row of cylinders.
• The diameter of the cylinder is 95.5 millimeters.
• Piston stroke - 94 millimeters.
• Working volume - 2693 cubes.
• Peak power at the exit - 135 horsepower / 99 kilowatt (at 4600 rpm).
• Peak torque - 217 Newtons per meter (at 3900 rpm).
• The number of valves in the GBC is 16.
• The degree of compression in the combustion chamber is 9.2.
• Power system type - distributed fuel injection.
• The type of cooling system is liquid.

Some power plants during restyling were modified before compliance with the ecological standard of Euro-3, and diesel disappears from the packages. What is in the earliest that in later models, there is one transmission system everywhere, namely the mechanical five-speed transmission box.

Information about the types of required oil

Hydraulic steering amplifier is recommended to fill with lubricating fluids corresponding to the specifications of Dexron II and Dexron III, as well as GM -6417 (Dexron IIIG). According to these criteria, the most optimal oils The following stamps are:

ATF II E.

It is a synthetic multifunctional hydraulic fluid designed to lubricate transmission systems, as well as for the operation of various mechanisms of the vehicle using hydraulic fluids (hydraulic power steering and others). According to the manufacturer this oil Excellent withstands high loads and sharp temperature differences, which guarantees fully operational operation of hydraulic nodes. Replacement intervals are calculated by 120 thousand kilometers, which is quite an excellent indicator.

ATF II E oil has the following properties:

1. Increased replacement intervals;
2. Increased resistance to high-temperature and low-temperature operating conditions;
3. Endowed with optimal viscosity and fluidity;
4. Increased resistance to degradation;
5. Increased resistance to chemical processes;
6. Endowed with excellent anti-wear properties;
7. It is very low temperature frosting;
8. Has excellent anti-corrosion properties;
9. Availability.

Wolf ATF D III

A semi-synthetic lubricating fluid having a high viscosity index. Used in most automatic boxes gear and power steering. Due to the fact that this oil has improved fluidity when used in low-temperature operation it provides effective lubrication of elements and reliable operation of hydraulic drives.

Wolf ATF D III oil has the following properties:

1. Increased wear resistance;
2. High resistance to oxidation;
3. High resistance to harsh temperature conditions;
4. Big resource.

Total Fluide G3.

Suitable for use in automatic and semi-automatic transmissions, as well as in the hydraulic steering amplifiers. It has a high viscosity index, which has positively affected the stability in operation.

Total Fluide G3 oil has the following properties:

1. Freezes at a very low ambient temperature;
2. Has excellent thermal stability;
3. High resistance to oxidative processes;
4. Neutral to sealing materials.

UAZ 31512 is a car Evolution of the old-good 469 "goat", which was released with huge thousands both for the Soviet Army and in the masses. The main advantage of this car lies in its maximum possible passability. Without exaggeration, this car will take absolutely everywhere, even where the roads never smelled.

His second dignity is unpretentious and unprecedented reliability, it is possible to refuel it, of course, only in extreme conditions, almost to all that can burn, and it can almost always go, even with the disabled with some mechanisms.

There are information that the military UAZ 469 with a punched engine could bring his driver to the destination if the pedal was drowning into the floor and pull out the subsoil, that is, if it does not cut it on time.

UAZ 31512 is somewhat different from its predecessor. The cabin has already changed here, in the direction of improving the comfort of passengers. Also, the engine was installed another, more powerful and with an injection principle of work. The car has become much more economical and comfortable to move. The suspension also has undergone significant changes: even on serious ugbach, the passengers do not fly their heads towards the ceiling. Well, of course, a steering power steering was installed, you can now rotate with my fingers, no longer need to apply all the muscle strength of the hands. Here is the element of the UAZ 31512 car, we will talk today.

Mechanism device

The steering power consumption is a device directly involved in driving a car and designed to increase the comfort of rotation of the steering wheel.

In addition to the hydraulic amplifier, there are also:

• Pneumatic.
• Electrically.
• Mechanical.

All of them are designed to simplify the driver's management process, but they work differently and can have a different effect on the car. So, the pneumatic amplifier is based on the principle of air pressure. The most constructive complex and unreliable, why it is rarely given to where it is this option. In his system, he has a balloon in which the air is injected, the compressor that pumps this same air and creates pressure and weight of the tubes and the hose by which the air moves into the mechanism. The slightest problem in the work of at least one element, and the entire system is covered. Those who have traveled on the traffic of the Kraz cars, which were released in Soviet times they know not to be larger, which this amplifier, in general, never works almost and turn the wheel steering wheel with all muscle strength.

On our UAZ 31512 installed a power steering - this is the easiest and most reliable option from all that can be offered. All its nodes, including the gain mechanism, rake, the pump for pressure creation and others fit in one place and are not dispersed throughout the car.

Alone only expansion tank It is located separately to facilitate the driver of the fluid replacement process throughout the system. The power of the steering wheel is in principle, as they work hydraulic brakes, with the only difference that there is always a pump-amplifier here, which creates pressure fluid pressure on the rail, which helps to rotate the steering wheel in the desired side.

Oil change and defect

Since our UAZ is usually moving very much by off-road, it often happens that oil begins to flow from it. And the power steering is no longer an exception here: overcoming complex obstacles usually badly affects it, although it is usually reliable on this machine. If it start to flow oil, you need to inspect all the nodes and replace the gaskets. We will tell how to check where the oil flows in the process of replacing the oil on this car.

First you need the car's engine cooled, therefore, and the oil in it will cool and will not be risks to burn while we will pick it up in it. While the car cools, we will deal with some container to drain the old liquid.

It is ideal for what can get under the car, because we will need to make gravity helped us to merge the butter in a smooth hose. Now it is necessary to examine in what state the expansion tank, if there are cracks and chips on it, then that's the reason was found. If not, we drain the oil from the tank: carefully remove the hose in its lower part and wear another, which by its second end is already omitted into the container.

Now you need to start the engine and twist the steering wheel in different directions so that the pump pumped the liquid and the whole it ultimately glass to us into the container. Now you need to look at all the nozzles that have a power steering, check their integrity and inspect the mechanism node itself. Most likely, on the nozzles or on the mechanism node, you will immediately notice the drips of the oil or cracks of some of the gaskets. If the bursting gasket or crack was detected in the nozzle, then they need to be replaced before pouring a new one. The next step will be fill in the tank of the new oil. All replaced, the flow is eliminated, the nozzle is replaced with a new and hydraulicel, in general, it has the look like from the factory. Now we pour new oil into the expansion tank of our UAZ. We pour it into two-thirds and put the canister with the remnants nearby.

Now we run the engine and move back from the side to the stron steering wheel. It is important that the cover cover of the tank remains open to the fluid squeezed by liquid has the opportunity to exit somewhere.

Along the way, watches the liquid from the tank completely, otherwise the pump starts to download air, and we, on the contrary, we try to get rid of it, so you immediately pour oil. The steering wheel of our UAZ must be rotated until little in the tank will no longer leave. When this joyful moment was noticed, then stop moving the steering wheel and the mooring motor. Take the oil into the tank to the desired mark and close the cover of the fuel throat. Now the steering wheel must rotate softly, and the car will turn more smoothly.

Well no

UAZ Patriot. Hereditary representative of the legendary Russian SUVs from the manufacturer known in the post-Soviet space. This car for many years of operation showed enviable resistance to dirt, dust and other surprises off-road. It is also not terrible small reservoirs. Heavy operating conditions led some features in the design of the UAZ Patriot nodes and systems.

The weight of this "passing" reaches 2 tons, so turn the steering wheel when the cross country of the rough terrain is not easy task. Designers, assuming, where most uaz patriot will be used, they came to the aid of the owners and integrated into the steering mechanism, such an indispensable element as a hydraulic power steering.

Any node B. modern car, including SUVs, needs periodic maintenance. In our article we will pay attention to this. For most owners, the construction of the amplifier is important, but the frequency of replacing the lubricating fluid in its mechanism. We have no doubt that it will also be useful to consider the purpose of the hydraulic amplifier.

What is it needed in the car?

In the modern automobile world, manufacturers seek to improve comfort in management. It did not go around the side and "brutal" russian SUV. UAZ Patriot. During the taxi, the owner rotates the "Barley", but it does it easily, because the specified amplifier comes to the rescue. All this happens during the operation of the motor, since the drive of the amplifier is carried out from the rotating pulley of the crankshaft. Try to rotate the steering wheel on the unused "engine" of the patriot. Yes, this is a gym! Riding on the road will turn into a test that does not endure every owner.

Thanks to the amplifier, the driver can turn the steering wheel with one finger. How was it possible? The main operating "face" in the strengthening mechanism is the pump. He gets the moment of rotation from the crankshaft. For such a transfer, the designers applied the belt. The pump generates fluid pressure, and in turn it is sent directly to the steering mechanism. It is at the expense of the "work" of oil the driver receives as a result of such an invaluable "relief" of rotation of the steering wheel.

To ensure circulation in the system there is a special trunk hose, which will talk about more. It has its own resource, so the owner should be attentive and follow its condition and replacement frequency.

Since they touched on the "repair" moment, we note that the list of such procedures concern Gur Patriot experts also include a replacement:

• hose;
• working fluid (oils);
• pump unit.

We reviewed the main directions of repair, without which the normal functioning of the gain mechanism can only dream of the carefree owner.

A little about the oil hose in the patriot

This trunk element serves to connect the pump with the steering mechanism. It is not famous for reliability, so the owner needs to show high attention to him. If the driver notices the capture of the wheel's reaction to the rotation of the steering wheel, which can be especially brightly manifested at speed, this should be a signal to check and subsequently replacing the hose. "Thanks" low-quality materials manufacturing materials, this hose is inclined after some mileage to swell, and this is a loss of pressure in the system.

Such a state of the element can provoke a rush, which is a prerequisite for emergency. Here the driver needs to have a spare hose with you. It is not a problem to purchase it, the main thing is to know the article - "3163-00-3408150-01". This product option has enlisted support from many owners. After replacement, the system will be pumped. It will remove air residues in the circuit.
The hose "3163-00-3408150-01" is presented in the photo.

Car Filter UAZ Patriot

Patriot designers applied in the hydraulic gain system the filter element. It is necessary for cleaning a constantly circulating oil. The replacement of this consumable component is recommended to produce together with the fill of the new fluid. Before buying, we strongly advise you to check the quality of the product, and it is better to determine the option in advance.

The plant puts on his UAZ patriot high-quality filters, so when you change, do not hurry to throw out the consumility, and try to read it "details" on it. The number and data of the manufacturer of the element will help to choose the desired option. Specialists advise you to draw a look at the product "Livna 4310-3407359-10".

This filter is shown here in the photo.

Let's go to the UAZ Patriot pump

This is the main component of the system. The unit is designed to create pressure in the circuit, which allows the mechanism as a whole to ensure the effect of amplification when the steering wheel is rotated. The task of car control for the driver is simplified significantly. To modify the UAZ Patriot "3163", the developers applied a separate pump, which can be found if inquiry in its catalog number. Here he is "3163-3407010". It is this product that the owner should be installed on his car.

Pump faults There are several. If damage to the body of the product occurred, then it is subject to unconditional replacement. Here, the owners can be recommended to consider the option from the company "Delhpi". The catalog of the unit is identical just to the one - "3163-3407010".

Is it time to replace the oil?

Lubricating fluid is a fundamental component of the hydraulic gain system. It is with its help that the required amount of pressure is created, on which the efficiency of the mechanism is depends. Over time, lubricant loses its condition and requires shift. Handbook of UAZ Patriot speaks of such a need to every 100 thousand km. Some owners apply for this purpose transmission fluids from famous manufacturers. These fluids have proven themselves quite well in the markets of many countries.

Let's look at the volume.

UAZ Patriot needs a little more than 1 liter. We advise you to purchase 2 liters.

Replacing the oil in GUR.

1. First of all, we hang the wheel of the front and remove the motor protection.
2. We look at the oil tank under the hood. It weakens the moment of tightening the clamp.
3. This tank will be required to tilt. So we solve the liquid from it. Eliminates the task of the corresponding syringe.
4. It's time to disconnect the liquid removal hose from the tank. It is also called a "return". His edge is lowered in drain capacityAt the same time, the steering wheel is full in front of both sides. We do it for three full-fledged turns.
5. Empty tank remove (recommend) and wash inside. It has a filter. We replace it with a new analog.
6. We take into the hands of a new oil and pour it into the washed and installed on the place of the tank. We ask the assistant during this process to rotate the steering wheel in both directions until it stops. The stronger and more agile assistant, the less air will be in the system. Watch the level in the tank - constantly replenish.
7. We draw attention to the drain hose. At the beginning of the process, dark butter appears from it. With the course of the procedure it brightens. This means that the new liquid "kicks out" the old oil in the GUR. This happens to the bay of about 700-800 ml. Now the system can be collected back.
8. I am convinced of the correctness of the assembly and launch the "engine". Turn the steering wheel and plunge the liquid to the required level.

Important! Motor at the same time do not let!

Replacing fluid in gur completed.

Consider the nuances

1. When pumping the mechanism of the wheel, the front is in possession. So we minimize the load on the steering knot.
2. The required volume of lubricant is 1.2 liters.
3. When the replacement of fluid in the GUR, omit the front of UAZ patriot, and let the motor work on "idle" about 15 minutes. We look at the level and on the compounds in the highway.

Let's summarize

The power steering is useful, especially in such a bulky SUV as a UAZ patriot. Mechanism maintenance is extremely important because it allows you to protect the owner from large waste to repair expensive components. Change the oil in the GUR on time, especially since the replacement of oil in the GUR is not a complex procedure, do not save on it. In the "loss" will not be left. This also applies to the pump GUR, who will have to seek replace over time.