What oil in Gur Chevrolet Aveo T250. Replacing the oil in the power steering hydraulicel and pumping the steering system of Chevrolet Aveo

19.04.2020

Hydraulic liquid performs one of the most important control functions vehicle. However, like any other oil, requires timely replacement. How to replace the oil in the steering hydraulicel on Chevrolet Aveo Alone, consider in detail the urgent article.

The process of replacing the oil

The power steering is the main node in the control system of any transport. In order for the GUR to be working, it is necessary to monitor the state of its parts, mechanisms, and also timely change the working mixture in the system.

Liquid Gur is an oil with which resistance is transmitted in the design from the pump to the hydraulic cylinder. In addition, the oily solution lubricates all the details, protecting them from excessive wear and friction. The circulation of oil in the GUR occurs according to the binding nodes and hoses, including the expansion plastic tank Gur.

On Chevrolet Aveo and many other TS oil hydraulic steering wheel is the main consumable materialwhose state determines all the operation of the node. However, the operating instructions do not indicate the exact timing of oil replacement.

Some car enthusiasts mistakenly believe that the hydraulic mixture, the plant in the plant does not require replacement throughout the entire period of operation of the Chevrolet Aveo car. In turn, experts recommend changing the solution after 150 thousand km of run. In some cases, the oily solution requires emergency replacement.

Signs of oil replacement GUR in Chevrolet Aveo car:

color change, sediment appearance;
the appearance of a specific smell (Gary);
efforts are required to rotate the steering wheel;
the appearance of noise, vibration, jolts when working with the wheel of the car

The appearance of such signs indicate a malfunction of the work of the GUR. In order to eliminate malfunctions, the first thing to be done is to replace the solution.

Initially, Dextrone II liquid or Dextrone III is poured at the vehicles in the vehicles. Accordingly, when replacing, you must select the same class or its analog.

Prevention of health GUR:

oil control control in an expansion tank (up to Max)
checking the color and smell of the mixture;
checking the tension of the drive belts;
verification of the camshaft GUR for leakage.

Timely preventive measures will be avoided by a car from excessive wear and save the driver's budget.

The process of replacing the oil consists of several stages:

Repaid the old mixture;
Filter washing;
Pouring new oil.

Also allocate complete or partial replacement Oils in the GUR system.

First stage

In order to replace the GUR liquid on their own driver, the following tools will be required:

cross screwdriver;
standard set of end keys;
jack;
medical syringe for 20 ml;
rubber tube;
blank packaging for draining liquid, with a capacity of 2 liters;
watering can;
new mixture.

Important: Works are performed only with a plugged engine.

Second phase

Initially, it is necessary to lift in front of the car with the help of a jack, in this position on the GUR system will not be given no pressure.

Instruction on the plum of the old liquid:

you must unscrew the plug expansion tank;
remove the filter and clean it using ordinary water or cleaning agent;
with a syringe and tube pump out the liquid;
disconnect the hoses and pour the solution into the container;
scroll wheels several times until it stops so to merge the fluid that remains in the system.

After the GUR is cleaned, you can start the bay of the new liquid.

Third stage

At the time of buying hydraulic fluid It is necessary to be guided by the rules:

Red solution is designed for cars with automatic box gears;
Green - for mechanics;
Yellow liquid is neutral and most often used in Chevrolet Aveo cars.

Pour the liquid into the expansion tank is necessary to the maximum mark. After that, you need to scroll the steering wheel several times until you stop. So the solution is distributed throughout the perimeter of the GUR. Perhaps after that, the fluid will need to add.

In the replacement of Oil GUR on Chevrolet Aveo, there is nothing complicated - everything can be done with your own hands. To change the working fluid of the power steering, it is necessary to need a syringe, an empty container for the old liquid, and, of course,.

How to change oil gur chevrolet aleo

The syringe should pump out the old liquid from the expansion tank. Then unscrew the attachments of the expansion tank and remove it to access the hoses. Disconnecting the hoses, you can drain the residues of the tank liquid.

Further, you should lower the hose into the container and twist the steering wheel - some more fluid will go. After that, you should install the tank, connect the bottom hose and plug the top hole in the tank. Pour new oil into the tank and twist the steering wheel, until the hose starts running clean liquid. Then connect the top hose, pour a new liquid into the tank to the maximum mark, start the engine and twist the steering wheel. If the liquid leaves the tank - to attach.

When to change the liquid of the GUR on Aveo

The regulation on Chevrolet Aveo does not indicate the frequency of replacement of the liquid GUR. Prescribed to check the liquid at the next maintenance Every 15,000 km and change if it becomes dark and muddy.

In the operating manual, Chevrolet Aveo it is written that the oil in the power steering is not changed at all. However, I noticed that the liquid in the system was very darkened, so it is still worth changing it. But why did the darkening occurred? The reason may be the malfunction in the steering or in the hydraulicel itself. But the diagnosis has shown that everything is fine there, so I will change only oil.

We prepare all the necessary tools, and you will need 1 liter of oil. Required tools These are: screwdriver with a crusade, pliers, a wrench at 10, a medical syringe of 20 milliliters, a segment of a small diameter tube, a compressor or a pump, and another empty vessel for the drain of old oil.

We turn to the replacement. Before starting work, make sure that the engine is cold, on hot motor We will not work. We turn off the tank cover and the syringe pump out the oil part so that the pressure in the system is reduced. You can roll out all the oil, in this case you will not need to pull the reverse highway hose. If you went to another way, then we remove the pliers and pull the backbone hose.

We turn around the tank mounting screwdriver with a power steering, remove it. The reverse highway hose is placed in a blank vessel, then we attach the pump to the fitting and let the air. Through the hose flows all the oil that is in the highway. After all the oil is removed, we make a pair of revolutions with a steering wheel in different directions, thus the residue of the oil is solved. Motor does not start. We put the tank to your regular place, pour new oil to the maximum level.

We start the car and as needed to fill the oil. Attention! The oil in the tank should always be, do not allow its complete disappearance. We make a couple of revolutions in different directions by the steering wheel already under the engine center. The wasting unit and after 15 minutes we repeat the procedure, so several times. So we remove all air from the system.

To replace the liquid, the following things will be required:

cross screwdriver;
key on 10;
syringe with a capacity of 20 ml;
short and small diameter tube;
pump;
some jar or bowl for the drain of the old liquid;
additive for gur;
new dextro 3, the volume of which is 1 liter;
additive for hydraulic steering;
passed, the tool is very similar to pliers, but there are some differences.

Gur, differently, the power steering is used in most modern cars. It makes it easier to control the car, and therefore, to enter a steep turn does not need to apply maximum effort. Part of the word "hydro" means one - the amplifier itself works with a certain fluid, or rather, on a specially intended oil. Control relief is created by tightness and pressure in the GUR system. In the case of exiting the fluid system, it simply ceases to fully function, which will make control complex and inconvenient.

In theory, replacing this fluid follows every few years if the mileage of your car is about 12-20 thousand kilometers per year. Definitely, to predict when the fluid should be replaced, because it all depends on the operation of a separate car. It is best to sometimes check the condition of fluid and control problems will not arise.
As the chevrolet manufacturer indicates, the need to replace the liquid in this car No, at the same time it becomes darker after a while, this is directly forced to produce a replacement process. Another cause of dark color can be different breakdowns in the car control system.

In fact, a lot of different tools and devices will be required, but believe me, comfortable control is worth it.

Step-by-step guide to replace liquid GUR Chevrolet Aveo

Let's start the replacement process itself. You should start with the fully chilled state of your car.

First of all, to reduce the pressure of the GUR, you need to pump out part, and even the entire liquid from the tank with the help of a syringe.
If you wish, you can speed up the process as follows: Purge some oil, and the rest is drained through the return highway hose. To disconnect the hose, it is necessary to stretch the claw claw a little.
Now it will be necessary to previously prepared a container for draining liquid and a little expectations before its complete drainage.
During the plot, you can find out in what condition is the filter if you find out of foreign objects, then try to get rid of them properly.
Next, we remove the tank before unscrewing the cross-screwing bolts that perform the target of the tank retainer. After that, effectively launder it and drain the residues of the liquid.
Pour old liquid into the container through the end of the return highway. By the fittings of the most highway we connect the pump or with the possibility of the compressor, thereby the air will allow you to push the remaining liquid. When the pump ceases to effectively act the car's steering side, but necessarily without starting the car.
Clean and dry tank put in his place, and pour into it a fresh liquid of the steering wheel in it, and it is worth pouring above the marks on the tank.
At this stage, the car engine should be launched and adding dextro to the tank, adhering to its level optimality.
When you work the engine, screw steering wheel Left and right, which contributes to a good distribution of fluid on the GUR system.
For 15 minutes, start the engine and repeat the previous step.
Subsequently, the proper distribution of fluid on the system its number in the tank will decrease, it means that we fill before the mark.
Having done all the stages correctly, you can safely consider the procedure for replacing the fluid GUR complete, which will make the management of your car much better.

Video instruction

If you have become noticing problems (a hum of or noise appeared when turning the steering wheel, etc.) in the work of the power steering (GUR) - it is worth thinking about replace oil in gur. Typically, such signs mean that hydraulic oil polluted and its replacement is required.

In Chevrolet Aveo, the oil change in GUR is not regulated, i.e. The driver should only monitor the level and attach the missing number. However, experienced ave products are recommended to replace the GUR liquid at least every 100 thousand km.

Help:

Volume working fluid The steering power steering is 1.1 liters.
The manufacturer recommends using DEXRON-III hydraulic oil in GUR.

Before you take on the replacement of the hydraulic fluid, we suggest familiarize yourself with the chapel control mechanisms of Chevrolet Aveo T-250.

Replacing Oil in Gur Aveo

To replace the liquid gur, you will need the following materials:

Medical syringe for 20 dm (it will be fine if you select 10-15 cm long tube for it).
The end key is 10.
Domkarat (needed in case of hanging the front of the car).
Pliers.
Capacity for the drain of the old liquid.
Watering can.
Rag.
Assistant (two to do the entire procedure, as well as pump from the air the system will be much easier).

Procedure for the replacement of oil in GUR

Open the BACK cover of the GUR system and the syringe to pump the liquid.
Pump the tank liquid
Unscrew the tank mount nuts.
Unscrew the tank

Also unscrew these two tank mount nuts
Pliers push the pressure hose clamp and disconnect it from the tank.
Disconnect the return hose
Install the drain container in the free space and direct the disconnected hose. If the container is installed below the fluid level, then part of it will be drained from the system independently.
Set the container to drain the residue of the liquid

To accelerate the pumping process of the liquid, the front of the car is highlighted (facilitates steering wheel rotation with an unbalable engine) and turn the steering wheel in different directions.

As it is an option for completely pumping fluid, you can connect a pump or compressor to the tank and blow the system, squeezing the remaining oil.
Disconnect the second hose from the tank and remove the tank.
Disconnect the second hose
Thoroughly wash the tank, gasoline can be used for this purpose.
A non-removable filter is in the tank, the contamination of which also negatively affects the operation of the hydraulic steering system. Therefore, if the filter is not cleaned, you should replace the tank to the new one.
The time has come to use the assistant (if you show a smelter, the assistant is not needed). Insert the funnel into the hose, which goes forward flow to the hydraulic plug (disconnected by the last place) fill the liquid and rotate the steering wheel from the side to the side. Take this procedure while the "return" will not go pure liquid.
Connect the hoses to the tank and install it.
Tear tank mount nuts
Different hydraulic oil to level.
Pour fresh oil in the GUR
Now you need to pump the system and get rid of the air, for this rotate the steering wheel and pour oil if the level is lowered.
Oil level in Bach Gur

Similar articles: