A guide to self-changing engine oil in a Ford Fusion car engine. How to change the oil in a Ford Fusion engine with your own hands? Ford fusion oil change intervals

27.09.2019

This video shows how an engine oil change is done. Ford Fusion 1.4. In addition, do-it-yourself oil and air filter replacement is shown - everything is included in the framework of the simplest car maintenance.

When to change, how much and what kind of oil to fill in Fusion

The oil change interval and Ford Fusion is 20,000 km or once a year, according to the manual. The air filter is also changed at the same interval. However, many drivers prefer to replace already at 10-15 thousand, citing severe operating conditions. Reducing the replacement frequency only harms the wallet.

Ford Fusion engine oil filling volumes:

Duratec 1.3 needs 4.35 liters of new oil;

Duratec 1.4 needs 3.8 liters of new oil;

Duratec 1.6 needs 4.25 liters of new oil;

Duratec-HE 2.0 needs 4.3 liters of new oil.

The number of the original oil filter for a gasoline engine is 1.4 - 1455760. Analogs: MANN W7008, FILTRON P629, MAHLE C1051, BOSCH F026407078, FRAM PH10044, ALCO SP1072, PURFLUX LS934 and some others.

Before buying an oil filter, you should clarify its applicability.

For diesel 1.6, the number of the original oil filter is 1359941. Analogues: MANN HU7162X, FILTRON E6671, MAHLE X1712D, BOSCH 1457429238, FRAM CH9657BEC0 and the like.

How to change the oil and oil filter Fusion

It will take: new engine oil, oil filter, rag, empty container for old oil (5 liters), funnel, 13 wrench and oil filter remover.

The oil is changed on a warm engine so that it drains better. If you unscrew the filler cap and lift the dipstick, the oil will flow out faster.

The car must be driven onto a ramp, overpass, pit, lift or put on a flat surface and jack up the front part, taking all precautions. If there is a crankcase protection, remove the protection. Then substitute a container under the drain hole on the crankcase, unscrew the drain bolt and drain the oil.

When doing this, be careful not to burn yourself with oil!

When the oil stops flowing out, tighten the drain bolt back. It's time to change the oil filter. If it's about gasoline engine, you can try to unscrew the filter by hand. If it does not come out, then you need to use a Crab-type puller. This will also spill some oil.

A new oil filter should be filled with new oil, about a third. The same oil is needed grease the rubber seal. The filter is twisted tightly, but by hand, about 3/4 of a turn, after the rubber band touches the seat.

Before filling oil, check whether the drain bolt and oil filter are securely tightened.

By installing a funnel, you can pour fresh oil into the engine. It is better not to fill everything at once - if you do not add about 300-400 grams of the required amount, you should tighten the lid and start the engine. After 5 minutes, turn off the engine and wait 10 minutes for the oil to drain back into the sump. After that, you can check the oil level on the dipstick and add as much as you need according to the marks. The level should be between the minimum and maximum marks, closer to the top.

Ford Fusion Air Filter Replacement

In addition to the fact that the Ford Fusion oil will be changed, the video instruction shows how to change the oil filter and air filter of the Ford Fusion engine. Since the easiest way, you can start with it, for this you will need to remove the engine protective cover (head on "10" and several latches) and disconnect the air pipes.

Original number air filter Ford - 1140778. Analogues: MANN C2244, FILTRON AP192, MAHLE LX1268, GOODWILL AG537 and others.

The Ford Fusion engine air filter is located in that plastic box above the engine, so after removing it you will need to disassemble it (10 Torx T25 turnkey bolts). Thus, the Ford Fusion air filter is replaced.

Changing the oil in a Ford Fusion engine is one of the most important and mandatory procedures when carrying out Maintenance car. The fluid in the system has a direct effect on maintaining the driving characteristics of the vehicle. Timely replacement significantly improves the operation of the mechanisms inside the power unit.

When is it necessary to change the oil?

The oil change schedule according to the manufacturer's service book is once every 15 thousand kilometers. The frequency of replacement in Russian conditions is 4-10 thousand kilometers. However, when replacing, not only driving performance and the terms declared by the manufacturer, but also the following factors:

Intensity of exploitation vehicle;
Seasonality (is the car idle in the garage during winter time of the year);
The technical condition of the power unit ( new engine or already supported);
Oil quality (recommended by the manufacturer or not).

What kind of oil to fill?

Many people wonder how to choose the right oil. Optimal choice and composition - recommended by the manufacturer.

14E8BA Ford Formula F 5W-30;
14E8B9 FORD Formula F5W30.

In the form of similar brands, there may be the following lubricating fluid: Total Quartz 9000 Future NFC 5W-30.

Oil change steps in a Ford Fusion 1.4 and 1.6 engine

Changing the oil in a Ford Fusion 1.4 and 1.6 engine is no different from each other. The only difference is the amount of lubricant being poured.

Before starting the fluid change procedure in power unit need to get ready for work.

Need to buy:

Oil (original or popular brand). Recommended viscosity 5W30.
Oil filter.
A plug with a gasket on the crankcase.

Required tools:

A 13 mm key to unscrew the drain bolt;
Oil filter puller;
A set of keys for removing the crankcase protection;
Screwdriver and pliers (if necessary);
Trough or bucket for draining waste fluid.

Step-by-step instructions for changing the oil in a Ford Fusion engine:

The Ford Fusion engine oil change process is complete.

Consequences of late replacement

Untimely oil change in the power unit negatively affects its resource. Operating a vehicle with low-quality fluid in the system will entail serious consequences.

The main ones are:

Deteriorated vehicle dynamics;
Increased fuel consumption;
extraneous noise;
Rotation of connecting rod bearings;
Deterioration of the internal mechanisms of the engine.

In addition to poor-quality lubrication, wear of parts occurs due to oil starvation. For this reason, there is a sharp increase in the temperature of the internal elements, which further leads to their destruction. From time to time it is necessary to check the oil level in the engine. Top up if necessary and check condition.

For the normal operation of FORD fusion, changing the oil in the automatic transmission or engine is of paramount importance.

Carrying out these operations in accordance with the manufacturer's MOT allows you to avoid many problems and extend the period of trouble-free operation of the car.

Ford engine oil change

Ford Fusion engine oil is replaced in the following sequence:

unscrew the neck plug;
clean the drain plug of the crankcase;
drain the used oil into a prepared container;
pour "fresh" oil;
wrap the cork.

Features of the service "Oil change in automatic transmission FORD"

When creating the FORD fusion gearbox, the manufacturer did not provide for the possibility of changing the oil, since when operating in European countries, factory filling is sufficient for the entire life of the car.

However, on Russian roads over time, the oil foams and loses its properties. As a result.

Perform waste disposal transmission fluid it will be easier if you carry out such a procedure 20 minutes after the trip. In this case, the oil will not have time to cool down and will flow out of the automatic transmission more easily. In total, it will take 15 minutes to drain.

To whom to entrust maintenance (oil change in automatic transmission, in the engine, etc.)

2BRO-SERVICE is a company specialized in maintenance and repair car FORD. We have modern diagnostic equipment, which allows us to identify any problems with cars of this brand, and we use high-quality Consumables and original accessories.

we carry out an oil change in automatic transmission and in the engine quickly and inexpensively;
we give the opportunity to personally observe the work of the masters on the monitor or in a reasonable way, for example, when they change the oil in the engine;
we have a staff of auto mechanics with extensive experience in repairing Ford cars of any models;
We provide cumulative discounts to regular customers.

Please note that during repairs at 2BRO-SERVICE, the factory warranty is preserved.

Contact 2BRO-SERVICE to entrust us with the MOT of your iron horse. We will do everything to ensure that your FORD FUSION is always on the move, and the need for repairs is reduced to zero.

The Ford Fusion is a cross between a station wagon and a compact van. This is a popular car from the American automaker, which is great for the role of a small family car. Fusion itself is inexpensive, which allows you to purchase it on secondary market at a favorable price. Wherein specifications and the level of reliability of power units are beyond doubt, allowing without serious problems and large financial investments to operate Ford for a long time. In order to maintain the optimal condition of the engine, the owner is obliged to timely visit the Ford Fusion, selecting high-quality and appropriate formulations.

Replacement frequency

The engines of the Ford Fusion car cause respect and admiration because they are assembled with high quality and provide long-term operation. Serious breakdowns occur only in the absence of competent maintenance. If you handle the engine carefully enough, change all consumables in time and use oils that meet the requirements, then it will pass the declared interval of 20,000 km without any problems. until the next shift motor fluid. There are several criteria that affect the amount of time or mileage between Ford Fusions.

Car manufacturer's recommendation. The official manual for "Fusion" states that the interval between changing the lubricant in the power unit is 15 - 20 thousand kilometers or 1 time per year. Given the build quality of the motors, their adaptation to Russian conditions operation, this figure is close to the real one. Engine oil is usually changed more frequently.
Terms of Use. In ideal conditions, it is almost impossible to use the car. Normal operation is aggravated by the quality of the road surface, driving style, poor fuel quality and other factors. The more difficult the conditions in which the Ford Fusion is located, the shorter the interval between mandatory. If the car is used regularly, driving more than 200 - 300 km. per day, then the declared interval between maintenance is reduced by 2 times.
Life time. Ford Fusion has been in production for a relatively long time. Older machines require more careful and regular maintenance, since the motor resource is running out, and the car needs close attention. Fresh specimens are not so demanding, therefore it is enough to change consumables for them according to the regulations.

The practice and experience of Ford Fusion owners clearly show that the average duration of a car's operation between oil changes is about 8-12 thousand kilometers. But it is better to do this at least once every 12 months.

Engine oil selection

It is better for the owner of Ford Fusion to build on what the manufacturer recommends for his car. In terms of official recommendations from the manufacturer, 2 oils are offered:

Ford Castrol Magnatec Professional E;
Ford Formula F.

But the choice for motorists is not limited to this. good and correct oil must meet the requirements for viscosity and quality. Therefore, focus on the most popular and well-established brands. They should include:

shell;
Castrol;
Mobil;
Valvoline;
ZIC etc.

Can be flooded in winter and summer seasonal oils, or manage with all-weather trains. Here choice is directly related to climatic conditions in each specific region.

Most often, Ford Fusion is filled with engine oils with the following viscosity indicators:

5W30;
5W40;
5W20;
10W40.

If you live in a region where winters are cold and temperatures regularly drop below -25 degrees Celsius, then these oils are suitable for you:

All-weather fluids in their marking provide for the presence of a winter and summer series. That is, all oils recommended for viscosity for Ford Fusion are all-weather (10W30, 5W30, etc.). If you fill in good engine oil, your Ford Fusion will ensure long and trouble-free operation of the power unit. Timely replacement of consumables and the use of high-quality components have a positive effect on any car. But you yourself have the right to choose which oil to use.

This car is filled with synthetic oils, as they guarantee optimal operation of all internal components and elevated level protection against premature wear. The use of semi-synthetics can lead to serious consequences for the engine. Variant with mineral oils not even discussed.

Filled volumes

Since the Ford Fusion is quite compact car family type, the manufacturer did not install large and powerful power units on it. There is no serious shortage of power here, since such cars are bought not for speed, but for comfort and safety. When choosing engine oil owners are also interested in its quantity. That, in the engine of a Ford Fusion car, directly depends on the power unit installed under the hood. The range of engines, taking into account all the modifications, is extensive on the Fusion. Although in fact the car is available with 4 engines (2 petrol and 2 diesel engines). Ford does not officially supply diesel versions to the CIS countries, therefore they can only be found in case of self-importation.

The main attention in Russia is paid to 2 gasoline engines:

A 1.4 liter Duratec engine with 80 horsepower requires 3.8 liters of lubricant.
If Duratec is under the hood, with a volume of 1.6 liters (101 Horsepower), then you will need to purchase approximately 4.1 liters of engine oil.

In addition to the engine oil itself, scheduled maintenance Ford should change the oil filter. If on original spare part if you don't want or can't spend money because it's quite expensive, then use a quality alternative. For Fusion, it is better to take Purflux or Bosch filters. Analogues are cheaper than the original, but are not inferior in terms of quality, efficiency or service life. So overpaying is not always wise.

Tools and materials

For and filter, you will need to pre-prepare some materials and take a standard set of tools. This list includes:

fresh motor lubricant;
new oil filter;
special key puller for the filter;
a new gasket for the drain plug (or a new plug assembly with a seal);
a set of keys;
capacity for 5 - 6 liters;
rags, etc.

If you have prepared everything, you can get to work.

Step-by-step instruction

In practice, even for a beginner, work on self replacement motor working fluid won't seem complicated. The process includes several steps. On each of them, try to act carefully, do not deviate from the instructions provided and follow the safety rules.

When working with Ford Fusion, it is better to change the oil on a flyover or inspection hole. In their absence, you can get by with an ordinary jack, but this is less safe.
Start the engine if the car has been in the garage for a long time. You need a warmed up power unit, because this way the engine lubricant will come out of the sump faster and in a larger volume when draining.
Under the hood, unscrew the filler cap. This will relieve the system of the resulting vacuum, due to which the oil will flow out quickly enough.
Move under the car. Usually the drain plug is closed by a metal crankcase protection. Some protections are initially provided with a window for easy access to the drain cover. Here, take a look at the situation. If it is impossible to get to the drain without dismantling the protection (and if it is present), dismantle the element with the appropriate suitable key.
Under drain hole place any empty container of suitable volume so that mining merges there. Unscrew the drain plug to the end. Be careful here, because the oil is quite hot and can cause burns if it comes into contact with the skin. Use thick gloves and put on a robe before work.
At first, the oil will begin to merge intensively, and then drain drop by drop. Be patient so that the maximum amount of old mining comes out of the system. When the engine is warm, experienced craftsmen advise leaving the grease to drain for 25 to 30 minutes.
While the engine fluid is draining, you can do the old oil filter. If you are not going to flush the Ford power unit, then change the element. Leave while rinsing old filter. It will take on residual contaminants, after which put in a fresh filter component.
To remove the filter, you will need a special puller key. The filter itself on a Ford Fusion car is located slightly above the oil pan. Therefore, do not rush to get out from under the car. Pry off the filter housing with a wrench, after which it can be completely unscrewed manually. Drain the remaining old oil. Please note that grease will also flow out of the filter seat, so be sure to substitute some kind of empty container there.
After removing the old element, clean seat from pollution. If necessary, use a metal brush. This will prevent dirt from getting into new filter.
Pour about 200 ml inside the filter. fresh motor fluid. Lubricate the sealing gasket with the same grease. This will soak the filter elements and firmly install the housing in place. First tighten the filter by hand as far as possible. Then, with a little effort, tighten with a tool. It is not necessary to overtighten, as excessive force will break the new filter.
On the drain plug, it is recommended to change the gasket if the plug itself has not yet worn out and is not deformed. If the quality of the cork is in doubt, it is better to change it completely. Otherwise, it will cause fresh engine oil to leak out of your Ford Fusion.
After installing the filter, get out from under the car and move to engine compartment. Pour through the already open filler neck right amount lubricants. Do not pour the entire regulated volume at once, as it differs from the actual one. Due to old oil residues in the system, in practice, less liquid is placed in the crankcase than required by the vehicle's technical specifications.
The bay is about 300 - 500 ml. less than the specified amount, let the oil drain for a few minutes. When cold, check the current oil level in the system with a dipstick. If it is not enough, add a portion of another 100 ml.
When checking on a cold power unit, the dipstick should show the level exactly between the “Min” and “Max” marks.
Close the filler hole, replace the negative terminal battery if you previously removed it for security reasons. Start the engine on idling and let it run for 4-5 minutes.
When the engine has idled for the desired time, turn it off. Now check the lubricant level on a hot engine. Usually it drops a little, so you have to add the missing amount of lubricant.
Repeat the topping up procedure as in the case of a cold engine. After each small addition, the engine must again be started and idling. Then wait for the grease to drain back into the crankcase and check the level with the dipstick.

If, with a hot power unit, the dipstick shows the required amount of engine working fluid in the system, then the work can be considered successfully completed. Additionally, look under the bottom of the car. It should be checked whether there are traces of leaking oil under the filter or drain hole. If drops appear, tighten the connections. When you have successfully completed the oil change, replace the protection and make a control run of 10 to 20 kilometers. Or re-check the level after a few days of operation. If the level of lubrication in the crankcase has not dropped, oil stains do not form under the machine, you have not made any mistakes in the process.

The oil change procedure on Ford Fusion engines can be performed even by a novice who does not have special skills and experience. Requires a minimum set of tools to work. The most important thing here is the selection of quality consumables.

Ford Fusion - refers to a number of subcompact vans produced by Ford Motor Company. The car received a base from Ford Fiesta, produced at the plant in Cologne, Germany. Not overpriced, good ground clearance, spacious interior and increased safety, all this is about Ford Fusion. Restyling of 2005 gave new moldings, modern lighting equipment, other front and rear bumpers and of course new design torpedo.

Car maintenance is a necessary task not only for the Fusion, but for any other car. By service we mean complete replacement engine oil along with a cleaning filter. To do this, you do not need to go to the service of a specialist and pay him money for work that every average car enthusiast can do. After all, almost every person can drain the old oil, change the filter to a new one and fill in the new one within an hour, a maximum of two.

What kind of oil to pour and how much?

Fusion car owners often pour synthetic product with a viscosity of 5W-30.

Official dealers fill in the original Ford Castrol Magnatec Professional E 5W-20. The choice of a company is not fundamental, it means that it is not necessary to buy an original product and use only it. You can buy any more or less normal company on the market, Castrol, Lux Molly, Shell and others.

A complete oil change for Ford Fusion vehicles should be performed every 15,000 km or once a year. However, many motorists do this procedure a couple of thousand kilometers earlier, thereby saving the engine from black oil.

In addition to the fluid, do not forget to change the filter elements as well.

The amount of oil required depends on the configuration of the engine and its power. Thus, for a 1.4 engine, up to four liters are required, and for a 1.6 engine, more than 4 liters of new oil.

1.4 Duratec (FXJB, FXJC, FXJA) - 3.8 L
1.6 (FYJB, FYJA) - 4.1 L

Instruction

Warm up the engine to operating temperature. Cold oil has a low viscosity (fluidity). The warmer the liquid, the faster it drains. Our task is to grind off as much dirty, waste liquid as possible.
For easy access to the drain plug (and in some models the oil filter is also attached from the bottom) and the bottom of the car as a whole, you need to jack up or drive on viewing hole (the best option). Also, in some models, "protection" of the engine crankcase can be installed.
We open air access to the crankcase by unscrewing the filler cap and dipstick.
Substitutes a large container (equal to the amount of oil being poured).
We unscrew the drain plug with a key. Sometimes drain plug made as usual "bolt" under the open-end wrench, and sometimes you can unscrew it with a four or hexagon. Do not forget to wear protective gloves, the oil will most likely wake up warm, but you need to be careful.
We wait about 10-15 minutes until the mining drains into a basin or a cut plastic canister.
An optional item but very effective! Engine flush special fluid not included in the service regulations and is not mandatory - but. A little confused, you will much better flush the engine from the old, black oil. At the same time, flushing with the old oil filter is carried out for 5-10 minutes. You will be surprised what black oil will pour out with this liquid. It is very easy to use this liquid. A detailed description must be included on the flush fluid label.
We replace the old filter with a new one. In some models, it is not the filter itself and the filter element that changes (usually yellow color). Impregnation of the filter with new oil before installation is a mandatory procedure. Lack of oil in a new filter before starting the engine can cause oil starvation, which in turn can cause filter deformation. In general, this is not a good thing. Remember to also lubricate the rubber o-ring before installation.
Fill in new oil. After making sure that the drain plug is screwed on and a new oil filter is installed, we can start filling in new oil, guided by the dipstick. The level must be between the minimum and maximum marks. Also, you need to remember that after the first start of the engine, a little oil will go away and the level will drop.
In the future, when the engine is running, the oil level will probably change, be careful the first few days of operation. Recheck the oil level on the dipstick after the first start.

Video materials

Similar articles: