Not a shkhodka, but close.
It so happened that at the end of last year it took another car, inexpensively, for a short, new and profitable. So that you can dispose of an existing Izh ODU and in general - new car, it is always nice. Even budget. Therefore, all representatives of the class B - Solaris / Rio, Logan, Polo and even Vesta were viewed. Initially, Polo was not in favorites, but the appearance of a new CWVA engine immediately made it such. Logan was indecent roads for that kidness that he represents, Vesta upset French checkpoints, and Koreans ... Koreans are Koreans. Well, of course, there is still a divine shkhodka - Rapid, and CWVA began to put on her since summer, but she did not get into the category "Budget".
In short, People's Wagen is a new polo. Just polo, because someone decided that in Russia they need sedans. Well, at least we have normal sedans, and not in India:

So, we have normal normal. In the summer they made a small facelifting, and in November finally set new engine. With the old CFNA polo to purchase was not even considered. Not due to the fact that he would have breakdown - and simply because I do not like flawed solutions. Cold, noisy and rattling engine is not interesting. Quickly phoned all dealers, and one has already found four suitable cars in stock. True, while I thought one evening, three already bought. Silver remained. It was issued. With a discount of 110 thousand - this is taking into account disposal. Disposal of his Iza quickly, and the Polo came from Moscow for the week.
Comforting Comfortline - Magnitol is able to communicate with the teleuxo telephone, heated seats and mirrors, but the absence of pulses. It is not enough, but you have to put alarm. Savings are kept, and inconveniences mass. Moreover, Volkswagen puts different blocks of comfort, and some can pick up the key from AliExpress. I am not lucky :) Well, I did not buy another block - the signaling was cheaper. The folkswagen jumper manifests itself with the mudguards - there are no front or rear from the factory, and the original are indecent money, although 700 rubles are sold at Skodelka. The steering wheel now became "leather", three-spoke. True without control of the radio. But with terrible glossy inserts - however, it is better than painted plastic from the Koreans.
In the cabin took another original mats for 4000 - plastic troughs with a pile coating.
After two days of operation on summer rubber (Cordiant Sport 2 from the factory stood) I realized that with the prickly wheels going crazy from noise. There are practically no shumkov on the arches. Therefore, I bought a European non-hat, Pirelli Snowcontrol 190 Serie 3. At the same time and test, as in St. Petersburg in the winter without spikes, although I am a cheap winter rubber In our climate. But it turned out - you can ride. Although you can ride on the summer, if it happens.
Well, and for 4 months I rolled 10 thousand. It should have been greater, but for various reasons it did not work. It and for the better.

What conclusions can be done?
The car is very budget. It feels in everything. Volkswagen she looks only outside. And for other indicators - approximately at the level of viburnum. The engine is heard perfectly - I can not imagine how it was with the old chain. Burchit exhaust system. From the unshamed tires, the noise is the same as in Octavia from Gislaved Nordfrost 100. Handling ... I do not know, for which it was so praised by half an edge into the autores. Nothing remarkable. Although, I agree - this is against the rest of the rest. The rest is worse. Upset glass - scrapets from the scraper is the norm, but for so much a short period, the right janitor began to rub the frontal one. Despite the fact that I rarely use janitors :)
They say the headlight light has become very better - maybe. Shines not bad.
The engine is heated very quickly. But this is a sense of this little: the salon warms up only after half an hour. The design of the stove has not changed, as a result, the car is cold. Although octavia with the same engine there are no problems with heating. But here everything is subject to everything, I just love rags, and for someone and 18 degrees on the climate - already Tashkent.
There are no speakers at all. Although the passport numbers are the same as Oktavia with 1,2TSI - but Skoda is just a plane in comparison with this atmospheric miracle. When trying to go quickly, it also eats a lot of gasoline, however, when driving a ride - only a little more than TSI. Although up to 160 accelerates. The average consumption is holding about 6.5. On the Skoda was the same, but I did not go to an example faster. She allowed :)
The trunk is not bad, the burnt under the spool is great. I threw the spare tire, and there folded a bunch of useful things. But the floor is made of thin fiberboard - as in Kalina. Alas. Rear is crowded, but and threesome can be ravaged. The tunnel is too big - one of the advantages of Solaris / Rio in its absence.
In general, for half a million - more than a decent option, especially with the current absence of choice. And this is the lack of choice very depressing ...

Tags: How air conditioning works on Volkswagen Polo Sedan

The following situation: When you click on the button, it is ignited, but there is no appropriate inclusion sound. Air respectively blows not cool. Checked fuses in the cabin, number 22 and 25, both are well.

Has wrote off to the officer. Who is thinking about this? And yet, the week put the alarm, the installers could have something like that?

Volkswagen Polo. Sedan 2012, 105 liters. from. - Electrician and electronics

25

Guys and on me on the go, when I was driving with kondeem in the salon, the sharp smell of the type of wiring and condo is finished working. What is thinking?

Hello. And at the moment I have the same thing, the smell of something burnt and after found that the climate does not see. You have something bad luck. Temperature on Street 7. It was necessary to turn on.

Confressor Konduyuk Daughter. Notpor did not clean the radiator, he clogged, ultimately overheating the system is excessive pressure and here's the result! Now, under the replacement, the radiator and compressor. Although there may be a radiator!

Have a good time day. He will not be flown with you, the temperature of the condushka does not affect the temperature.

but on the sink, when the car was fingering, I heard how the condo and the air is a cool bleach.

The air conditioner compressor coupling is not included. There is no mass on the air conditioner compressor

Not The compressor coupling is driving air conditioner. On compressor air conditioner No mass. VW Golf 4, Passat, Polo, Bora.

VW Polo Sedan ( air conditioning Bad cooling) hot air flow damper!

Try to turn on once again. The handle is all on the glass (up) Press the A / S.Oll button will determine the characteristic click. Glue the compressor, the pulley should be spinning, the engine speed will slightly fall, the evaporator fan will turn on. (depending on temperature) if you have all the rules. There will be a question on cold, write

Hi, tell me the same story The indicator is fastened but not turn on and there is no characteristic click, where to climb what to watch, maybe there is a relay?

Infa was confirmed, I checked on the car. Condes turn on I. works))

Check the pressure of freon in contours. More details describe a malfunction.

i think on lethah I figure out 100% works he or not)

I had it in the spring, but the degree was 10 somewhere, rain, slush. In the morning I started everything worked, I drove to the mother-in-law, went to her for half an hour, then came out, started, drove and feel straight stiffishly terribly and the windows sweat. I come on to poke the Condeye button (I have a sleeper-control), but nothing happened! In the evening, it climbed into the Internet, and a hundred there just did not read, I decided to also sign up for the service! BUT! In the morning, the machine was pleasantly surprised, condo works🙂

well, right now, it shows, tomorrow if I also go to the garage and check there.

below 4 will not turn on.

Where does this information come from?

on the street how many degrees? After 0 degrees, it will not turn on.

Similar news

The new Volkswagen Polo is very popular vehicle In the world, including on the territory of Russia. Our client remains that there is that the famous German manufacturer managed to cooperate several important features in this machine: usually the highest German quality and the price that makes this car very easier ...

1.1.4. Gearbox control. 1.1.5. Outdoor lighting switches, headlights light beam control regulators, steering wheel switches, switches block on the instrument panel. 1.1.6. The control unit of heating, ventilation and air conditioning, rearview mirrors, salon lighting. 1.2. Safety in repair. Forum Volkswagen.

1.1.6. Volkswagen Polo.. The control unit of heating, ventilation and air conditioning, rearview mirrors, salon lighting.

Heating, ventilation and air conditioning

The car, depending on the configuration, can be equipped with a system of heating, ventilation and air conditioning with manual control and automatic climate adjustment in the cabin - climate control system. The air into the car's salon can act through the central and side deflectors located on the instrument panels, as well as through the air ducts - to the feet of the driver and passengers.
The cabin air purification filter prevents dust and harmful particles in the air in the air.
It turns out the air from the salon to the trunk through the ventilation grids located in the shelf under rear glass. From the trunk, the air comes out through the grilles under the rear bumper.

Side deflector of heating, ventilation and air conditioning system: 1 - lever changes in the direction of air flow direction; 2 - the intensity regulator of air intake.

Central heating, ventilation and air conditioning system deflectors.
The control unit of the heating system, ventilation and air conditioning is located on the center console of the instrument panel.

The control unit of the heating system, ventilation and air conditioning (on car controlled vehicles): 1 - air temperature controller; 2 - switch mode of the heater fan operation; 3 - air flow distribution regulator; 4 - the air conditioner switch button; 5 - Air Recycle Recycling Switch.
By turning the handle of the air temperature controller 1, change the temperature of the air entering the interior. To increase the air temperature, you must rotate the knob of the regulator to the right, in the red sector of the scale, and to reduce the air temperature - to the left, in the blue sector. The intensity of air supply to the salon is regulated by turning the handle of the fan operation mode switch 2. In this case, one of the four fan rotation rates are turned on. Turning the knob of the switch clockwise, increase the speed of rotation of the fan. Air flows entering the salon can be adjusted. The flow distribution regulator 3 sets the following direction of air multiple air in the cabin:
- Air flow through deflectors in the instrument panel enters the top of the car's interior;
- The air flow comes only to the driver's location zone and passengers;
- the air flow enters the location zone, as well as to the lattices of blowing windshield;
- The air flow comes only to the lattices of windshield blowing.
To enable air recycling mode, press the switch button 5. In this case, the indicator lights up the button. To turn off, press the button again. Air recirculation mode (termination of the outdoor air supply to the cabin) It is recommended to use if necessary to quickly reduce or increasing the air temperature in the cabin, as well as when driving on dusty terrain or in a dense traffic flow to avoid dust, exhausted gases and unpleasant odors.
It is not recommended to use recycling mode for a long time, as this may lead to an increase in air humidity in the cabin and fogging glass.
To turn on the air conditioner, press the 4 switch button with the engine running and the heater fan turned on. In this case, the indicator lights up the button.
Re-pressing the button turn off the air conditioner. The air conditioner is also turned off when the heater fan is turned off. On the protracted lines or in the conditions of intensive urban motion, the operation of the air conditioner can lead to overheating of the engine. Therefore, if the cooling fluid temperature exceeds the allowed value, the air conditioner should be turned off. If the car is put on the parking lot in the right rays of the sun, before turning on the air conditioner, you must open the windows and ventilate the interior. To avoid fogging in rainy weather, you need to set the maximum fan speed, turn on the air conditioner and transfer the air flow distribution regulator to the position, while the air temperature controller is recommended to be installed on the border of blue and red zones.
After a long parking lot in hot weather in the sun When the air conditioner is turned on, do not direct the flow of cold air to the windshield in order to avoid cracking.
If there is no need to use the air conditioner, it must be included every month for several minutes, and even in the winter period of operation (during thaws).
This contributes to the preservation of lubrication on the parts of the compressor and seals, which extends the service life of the air conditioning system.
The car can be equipped with climate control system, which automatically controls the temperature, quantity and distribution of air flow and regulates them depending on the conditions specified by the driver, as well as weather conditions. This saves the ability to manually control the system.
The climate control control unit is located on the center console of the instrument panel.

Climate control control unit: 1 - fan rotation speed regulator; 2 - information display; 3 - air temperature regulator; 4 - air conditioning power button; 5 - the air recirculation mode button; 6 - buttons distribution of air flows in the cabin; 7 - Inea / moisture removal mode button on windshield; 8 - System Enable Button automatic control microclimate.

Pressing button AUTO. Includes automatic mode at which the set temperature in the cabin will be maintained automatically. When you press any of the climate control buttons, the automatic mode changes - the button is on, the function will be managed manually, the remaining functions are automatically. Turning on and off the air conditioner is carried out by pressing the button 4. When the air conditioner is turned on, the inscription will appear on the display. AC. The fan rotation speed is adjusted by the rotation of the regulator 1. The fan settings are displayed on the display in the form of strokes. The direction of air flows in the cabin are set by buttons 6. Button 5 is used to select the feed mode to the car of the outdoor air and recycling, when the feed in the outdoor air interior is stopped. To remove an inlet / moisture from the windshield, a button 7 is intended. When you press this button, the air conditioner will be automatically turned on, and the air recirculation is disabled. In this case, automatic control of the frequency of rotation of the fan and air temperature in the cabin occurs.

REAR VIEW MIRRORS

Depending on the configuration on the car, outer rear view mirrors can be installed with manual or electrical drive and heated. The position of the outer rear view mirror with manual drive is adjustable from the car's interior with a turn of the mirror handle. To adjust the position of the rear-view mirrors ...

... The driver's door armrest is located.
To adjust the position of the left or right outer mirrors, we translate (with the ignition turned on) the knob of the regulator, respectively, to the position L. or R.. Then, tilting the handle to the right and left and back and forth, change the position of the mirror. To turn on the heating of the mirrors, we translate the knob of the regulator to position 1.
When the electric drive fails, the mirror position can be adjusted manually by pressing the edges of the mirror element. The position of the inner mirror of the rear view can be adjusted in horizontal and vertical planes, turning the mirror body on the hinge. There are two modes of the position of the inner mirror: "Day" and "Night". To reduce the blinding action of the headlights of moving from behind, we translate the mirror to the "Night" position ...

... moving back the lever located at the bottom of the housing.
In this case, the angle of reflection of the mirror and the blinding effect decreases.
It is not recommended to place items on the shelf in front of the rear glass that can reduce the viewing zone through the mirror.

Salon lighting plander

In the upholstery of the ceiling of the car, the plane is installed, in which the interior lighting lamp and two directional light bulbs are located.

Salon Lighting Plafof: 1 - Fixture Lamp Switch Button; 2 - key switch lamp lighting of the cabin and directional light; 3 - section of the direction of directional light; 4 - section of the interior lighting lamp.
When you press the 1 button in the ceiling, the corresponding directional light lamp lights up. When you press the lamp button again goes out.
When not pressed (average position), the key 2 lamps of the interior lighting and directional light are automatically lighting up when the car is unlocked, opening one of the doors or removing the key from the ignition lock.
The lighting turns off after a few seconds after all the doors are closed or immediately after turning on the ignition. When you click on the right edge of the 2 keys, all the lamps of the ceiling light up. To turn off the plaffone lamps, press the left edge of the key 2. In this case, the directional light lamp can be turned on by pressing the corresponding button 1.

Circuit diagram of the movement of air flows in the heating system Polo sedan, air conditioning and ventilation: 1 - flexibility blowing deflectors; 2 - airflow distribution valves to windshield deflectors and device panel deflectors; 3 - Deflectors of the instrument panel; 4 - air ducts heating the zone of the driver and passengers; 5 - Airflow distribution valve to device panel deflectors and heating ducts of the driver and passengers; b - heater radiator; 7 - saloon air filter; 8 - air recycling system damper; 9 - airprokery box; 10 - air intake in the car cabin; And - the impeller of the fan; 12 - fan electric motor; 13 - air conditioner evaporator; 14 - drainage hole for condensate drain; 15 - temperature controller damper; 16 - Housing of the system of heating and air conditioning

The heating, air conditioning and ventilation system is a single complex that provides the most comfortable conditions in the car's cabin, regardless of the weather conditions and motion mode. The system includes a heater (increases the air temperature at any modes of operation of the system), air conditioning (reduces the temperature and humidity of the air), the air pressure (fan) and filter air ducts (provide air exchange in the cabin, clean the air from dust), as well as the control unit ( Manages all the elements of the system to obtain specified comfort parameters).

A liquid type salon heater is installed on the car.
The heater radiator is combined with the engine cooling system with two hoses passing in motor compartment.

The radiator is placed in a plastic climatic block cover, mounted under the central part of the instrument panel. Basic heater nodes:

Heat exchanger (radiator) 6 heater designed to heat the air coolant entering the air to the air salon;

fan (air supercharger) 11;

For clarity, it is shown when the blows of the air of the inflow and the air intake are shown.

Electric motor 12 fan with excitation from permanent magnets, providing an adjustable outdoor air supply to the heater and air conditioning valves. To obtain different values \u200b\u200bof the fan speed in the power supply circuit, an additional resistor unit is installed;

The valve 15 of the air temperature regulator coming from the heater to the salon. The amount of air passing through the heat exchanger of the heater and the outer air passing through the heat exchanger;

The valve 2 of the air distribution coming from the heater through the air ducts into the salon or to blow the windshield.

Features of the device of the air conditioning system

On the vOLKSWAGEN cars Polo Sedan Installed compressor air conditioning system. The heater nodes and the air conditioner heat exchanger heat exchanger are connounted in one block. The air conditioning system controls are located on the panel, common with the heater controls.

The compressor is installed on the engine cylinder block and is driven by a polyclinite belt. The compressor provides the circulation of refrigerant in the system. The compressor shaft is installed in the aluminum front cover of the housing on the bearings and is sealed from the drive side of the drive with the gland. The compressor drive pulley is mounted on a two-row ball bearing and when the engine running is constantly rotating. The torque is transmitted from pulley to the compressor shaft through the slave disk.

Circuit diagram of refrigerant movement in air conditioning system: 1 - combined pressure sensor; 2 - a plot of high pressure pipeline; 3 - Receiver-desiccant; 4 - High pressure line service valve; 5 - condenser (air conditioner radiator); b - condenser fan and cooling system radiator; 7 - air conditioning compressor; 8 - Low Pressure Pipeline section; 9 - service valve lines of low pressure; 10 - heater fan; And - evaporator; 12 - thermostatic valve

If the system is properly, while the air conditioner is turned on, the clutch is a clamping clutch disc under the action of an electromagnet comes into engagement with the pulley of the drive, and the compressor rotor begins to rotate.

But during the operation of the air conditioner, the following compressor faults may occur.

1. If when the air conditioner is turned off, the coupling is published during rotation outsided soundsThe smell of Gary is heated or appears, it probably began to collapse her bearing. In this case, it is necessary to replace the bearing. In some launched cases, it may be necessary to replace the compressor coupling assembly or components of its parts.

2. If after switching on the air conditioner, it is not audible, then the following problems are possible:

Refrigerant leakage occurred, and the control system blocks the inclusion of the compressor;

The pressure sensor in the system has failed;

Malfunctions in electrical circuits of the control system;

The winding of the coil of the coupling electromagnet burned;

Engine control unit for any reason ( heat Engine coolant, high revs Engine) blocked the inclusion of the compressor.

3. If the coupling rotates easily and freely, but when you turn on the air conditioner, extraneous noises are clearly audible or even stalls the engine, then most likely sworn

Compressor. The inner pumping part of the compressor is not subject to repair. In this case, the compressor will have to be replaced.

4. And the last, the most unpleasant option. Click is distributed, the coupling easily rotates the compressor shaft, and the cooling of the air in the cabin does not occur. In this case, the compressor works in a frightened, nothing pumping. Only an experienced specialist in the presence of special control and diagnostic equipment can determine this malfunction.

You can most accurately determine the cause of the malfunction after complete diagnosis in a specialized service center for the repair of automotive air conditioners.

At the bottom of the rear compressor cover, an emergency pressure reset valve is set. In the case of pressure growth in the system in the failure of a pressure sensor or other abnormal situations, when the installed maximum pressure of the valve membrane is destroyed and part of the refrigerant is ejected to the street. As a rule, after this, the emergency valve does not have sufficient tightness. Therefore, after eliminating the causes that caused pressure and reset the refrigerant, the valve is subject to a mandatory replacement.

When the valve is triggered, the refrigerant is unexpectedly ejected by strong jets in all directions. To prevent injury, people were closed by a cap.
Conductor (air conditioner radiator) multithreaded type is located in front of the engine cooling system radiator. It is attached using brackets to the cooling system radiator. Condensor cells are made of flat thin-walled aluminum tubes with internal longitudinal partitions for rigidity and outer fins to improve heat exchange. Aluminum tanks, with flanges for connecting pipelines and receiver. In height, the tank is divided into sections, therefore, passing through the condenser, the refrigerant flow changes several times the direction. In condensor, the steam condensation of the refrigerant compressed by the refrigerant compressor and the heat of heat released into the surrounding air occurs.

When the air conditioner is turned on, the engine control unit turns on the power supply circuit of the electric fan of the engine cooling radiator, which improves heat exchange in the condensor and reduces the pressure in the air conditioner system.

At least once a year, it is better before the start of the summer exploitation, wash the fins of the cells of the condenser from the nanice dirt, dust and antifungal reagents B. This will improve heat exchange, reduce the pressure in the system and increase the service life of the system elements.

Do not use condensor for washing with water jet under high pressure. This may damage in thin-walled feet of fins. Even with a regular car wash, the need to replace the condensor arises much more often than I would like. The fact is that he first assumes the flow of antifungal reagents, dirt and pebbles from the road. It is thin with the walls of the tubes ... In most cases, the condenser is damaged by corrosion to the third-fourth year of operation.

If the corrosion is disturbed by the tightness of the condensor, then repair it is more expensive. Even if the argon welding welker succeeds in patching the hole, there is soon the appearance of leaks elsewhere. By the way, the pressure in the system on hot days can reach up to 25-28 bar.

In addition, the complex structure of the condensor tube should be taken into account: along it is divided by partitions to the channels, so the likelihood is great that after welding, part of the channels will be blocked. Accordingly, the power will fall and the work of the air conditioner will deteriorate, especially in traffic jams and in hot weather.

After each experiment with the latch of the condensor, it will be necessary to pay for the removal of the installation, welding of the condensor and refueling the refrigerant system. So it is better to immediately install a new condenser. Instead of an expensive original, it is quite possible to buy a cheaper condenser from authorized spare parts manufacturers.

The evaporator is located in the heating system and air conditioning system. The evaporator is made of aluminum tubes with outdoor fins to improve heat exchange. Passing through the tubes of the evaporator, the boiling refrigerant actively absorbs heat

From the air that blows out the outer fins of the tubes. The air is cooled and the fan is supplied to the interior of the car.

When cooled through the air evaporator, the water vapors contained in it are condensed.

Condensate through a drainage tube connected to the body of the heating unit block ...
... and extended through the plastic adapter at the bottom of the right side of the engine shield, merges under the bottom of the car. With high humidity of the surrounding air under the car, water can be formed, which is an indirect feature of the condition of air conditioning.

During the operation of the car on a moist of condensate the outer surface of the evaporator, particles of road dust and dirt are sedired.
This layer becomes an excellent living environment and rapid reproduction of rotten bacteria and fungal crops. Over time, an unpleasant smell appears in the car. It is especially felt at the time of turning off the air conditioner and in wet weather. In order to minimize the risk of this problem as much as possible, when buying a new car, it is necessary to conduct preventive processing of the evaporator with special chemicals, replace regularly salon filter and clean the drainage tube. If, despite the measures taken, the smell still appeared, contact specialized service Repair of automotive air conditioners for disinfection or washing of the evaporator. With very strong pollution, the evaporator will have to be replaced.

On the side surface of the evaporator there is a flange for mounting the thermal control valve.

The block-type thermostatic valve is located in the evaporator case. The valve is attached to the pipelines and evaporator using flange connections. Having passed through the throttling hole in the valve body, the liquid refrigerant sharply reduces its pressure and begins to boil. In the valve body, an adjusting element is installed changing the flowing section of the throttle opening depending on the pressure and temperature of the refrigerant. The adjusting element is configured at the factory and during operation the adjustment is not subject to.

Receiver-desiccant is installed on the condense on the left side and is a collapsible block. Inside the case there is a filter element (cartridge) filled with desiccant granules (silica gel). A liquefied refrigerant passing through the receiver is cleaned from possible impurities, dirt and moisture. At the top of the receiver case, a hole is located to replace the filter element.

In the case of repair or replacing the elements of the air-conditioning system, if it was in the open state (any nodes were removed, pipelines were destroyed, etc.), the cartridge of the receiver-desiccant is to be replaced. Otherwise, after refueling the refrigerant system, the acids can be formed inside the system, which destroy the parts of the air conditioner from the inside.

Flexible insert hose design: 1 - outer protective sheath; 2 - fabric cord power frame; 3 - plastic sealing layer; 4 - internal oil resistant layer

Pipelines connect all the elements of the air conditioning system into a single hermetic circuit. Pipelines and fastening flanges are made of aluminum alloys.
Wrap metal parts of pipelines from dents and beggars. Any narrowing of the pipeline cross section leads to a decrease in system performance.

To connect the intercommunicative elements of the pipeline system in some areas are supplied with flexible inserts from synthetic materials.

In places of compounds of individual elements of the system, sealing rings of a round cross section of neoprene are installed. During the repair of the system, when separating pipelines, sealing rings are subject to mandatory replacement. Threaded pipelines tighten the recommended point. Weak or excessively severe tightening leads to deformation of the sealing surfaces and refrigerant leakage.

Service valves for connecting diagnostic and filling equipment are located on pipelines.

So arranged on pipelines, service valves of high a and low-d lines of pressure.
Valves are closed with threaded caps to protect them from dirt.
Sloves are installed in the valves, similar in design with spools of tires of wheels, but differ from them.

Special key is used for turning and screwing the spools.

Check the presence of refrigerant in the system by pressing the spools of the service valves are prohibited, since after such an inspection, the valve spool can not fully close and refrigerant leakage will occur from the system!

The pressure sensor is installed in the motor compartment on the high pressure line pipeline.

According to the sensor signals the electronic unit The motor control disables the air conditioner compressor when the system is deployed or an emergency increase in pressure in it in order to protect the compressor from overloads.
The control unit of the ventilation system, air conditioning and heating and car heating is installed on the instrument panel consoles.

Air temperature sensor in the cabin

Located in the front panel of the control unit, if the climate control system is installed on the car. To exclude incorrect readings of temperature values \u200b\u200bdue to the effect of heated elements of the panel, the sensor is equipped with a compulsory blowing system. The system provides a uniform air duct from the front of the car's interior through the sensor housing. For normal air movement, protect the input hole of the sensor housing from any solid particles or fluid. This is especially true of cases of chemical cleaning of the cabin. During the cleaning of the salon, the vacuum cleaner is strictly forbidden to bring the suction tip of the vacuum cleaner pipe to the sensor inlet. With a difficult airbone through the sensor housing, the normal functioning of the automatic climate control system is broken.

Sensor outdoor temperatureAlthough it is located in the front of the car behind the rubber cladding in a protected from solar radiation and ventilated location, exposed to such factors as warm air from the engine and radiation from the heated asphalt. Therefore, its testimony can sometimes be somewhat overestimated, especially after a long idleness in traffic jams. The appearance of the outdoor air can be considered correct when driving at a rate of at least 40 km / h for at least 10 minutes.
To improve the efficiency of the climate management system and a more comfortable distribution of air flows in the cabin, a solar illumination sensor is installed. Depending on the degree of heating the cabin with the rays of the sun along the sensor signals, the air flows are sent to the head or foot of the driver and the front passenger. The sensor is located on the instrument panel near the windows glass.

Refrigerant. The system is refilled by the HFC134A refrigerant (R134A). Added to refrigerant special oil For lubrication compressor. It is strictly forbidden to use refrigerants and oils of other types in the system.

During the operation of the automotive air conditioner, situations occur periodically when maintenance of the air conditioning system or its repair is required. This uses modern diagnostic and repair equipment. The most common situation is the deployment of the system and the exit of the refrigerant.

To detect leakage places, highly sensitive halogen leaks-swelkers are used with sound indication.

In some difficult cases, the so-called method is used. Ultraviolet diagnostics of the tightness of the autoconditioner system.

The method is that a special dye is introduced into the microDosis system.

In places of microtheps, the dye together with the refrigerant gradually goes to the outer surface of the system elements.
During the inspection of the system, the dye begins to glow (fluoresce) under the action of ultraviolet rays of a special lamp ...
... and refrigerant leakage places are visible.

It should be noted that the dye does not have any negative impact on the system. It can be in a refrigerant and circulate on the system how long and serve his service only when the leakage occurs.

After repairing the autoconditioner, it is necessary to evaporate and refuel the system with a corresponding refrigerant (R134A). The volume of refueling the auto air conditioner for each car model is individual.

To carry out high quality refueling of the automotive air conditioner are necessary:

Precision manometer blocks with special connecting tips:

Two-stage vacuum pump To completely remove air and water vapor from the system;
- High-precision (division price no more than 5 g) scales for dosing the refilled refrigerant.
Due to the specific features of repairing the air-conditioning system, this section describes only the work on the removal and installation of individual elements and the system control unit. Works associated with refueling the refrigerant system should be carried out in specialized service centers.

The air conditioning system is refilled by a high-pressure refrigerant. The liquid refrigerant hitting the human skin causes a strong frostbite, so all the work related to the service, repair or dismantling of the elements of the air conditioning system, spend whenever possible in specialized service centers equipped with professional technological equipment. When carrying out work on your own, take precautions.

Features of the device of the ventilation system

The vehicle ventilation system is applied by car. The outer air can enter the interior through the windows of the doors when the glasses are lowered ...

And through the air box grille, located in front of the windshield in the air intake. The air from the air intake is fed through the air ducts to the car's salon through the winding winding nozzles, side and central nozzles, through the lower nozzles of the heater housing.

The air from the street entering the car is purified from dirt particles and pollen in the cabin air filter, placed in the body of the climatic unit.
Filtering element air filter It is necessary to replace in accordance with the deadlines for preventive work, exhaust ventilation is carried out through the grids, which are made in the rear cladding of the trunk.

When the goods are placed in the trunk, if possible, try not to illuminate the ventilation grids, leave a small gap between the luggage and the facing panel. Effective exhaust ventilation work improves temperature mode In the cabin and reduces the formation of condensate on windows windows.

From the side of the exhaust ventilation holes, closed with deflectors with petal valves, which are installed in the back of the body, in the cavity of the rear bumper (view with the removed rear bumper).

Security Rules for the repair and maintenance of the air conditioning system

1. The refrigerant is a chemical composition requiring careful appeal to avoid harm to health.

2. It is necessary to work in a well-ventilated room and avoid inhaling the chest of refrigerant.

3. When performing work related to the depressurization of the air conditioning system, you must always wear safety glasses and wrapping fittings, valves and connections with clean cloth.

4. It is forbidden to carry out welding work by car near the units and pipelines of the air conditioning system.

5. It is forbidden to curb flexible inserts of pipelines (hoses) by a radius, less than four diameters of flexible insert.

6. There should be regularly inspecting the hoses for the appearance of cracks and scuffs.

7. Before disconnected of the air conditioning pipelines, it is necessary to remove the entire refrigerant from it.

8. Turning the threaded connections of the system elements should be slowly. Do not bring the face and hands to the place of separation to avoid injury when there is a liquid refrigerant residue in the system.

9. When detecting the pressure pipelines during disconnection in the system, refrigerant must be removed from it.

10. After separating any area, it is necessary to immediately close the holes with caps or ribbon. This will prevent the moisture and dirt entering the system, which the ILO cause the failure of the pumping part of the compressor.

how turn on air conditioning on the volkswagen Polo.

Heater and Air Conduct

With the right use of the abilities of the heating and ventilation system of your car in the cabin, comfortable habitats are provided and the fogging of glass is eliminated.

If your car, when buying, was not equipped with air conditioning system. You can at least what time to install this system on own car. To do this, contact 100 Honda to equip the vehicle with air conditioning system made at Honda plants and meets all the requirements of our company.

Heating control panel, ventilation and air conditioning

Fan regulator knob

Moving the handle to the right leads to an increase in the frequency of rotation of the fan and supply the air into the car interior.

Air temperature controller knob

Move the handle to the right leads to an increase in air temperature entering vehicle interior.

Air conditioner switching button (separate models)

The A / C button is designed to turn the air conditioner on and off. When the air conditioner is turned on, the indicator built into the button lights up.

Read the same:

Air Recycling Mode Button

The button is designed to turn the air recycling mode.

When the recirculation mode is enabled (as evidenced by a burning indicator, built into the button), the car interior is isolated from the atmosphere and entering the fresh air interior stops. The fan provides air circulation over a closed contour. If you re-press the button and turn off the recirculation mode (at the same time the indicator built into the button will go out), fresh outdoor air from the atmosphere will begin to the cabin.

Turns on air distribution modes

Buttons are designed to select the air distribution mode.

The outer air enters the salon through the central and side ventilation deflectors located in the control panel.

Read the same:

Pens air conditioner Volkswagen Polo

Low price sets presented on video details Easy installation \u003d new view of your Polo ! -~-~~-~~~-~~-~-.

VW Polo Sedan (air conditioning is badly cooled) damper of hot air flow!

Cars with 5-door Hatchback

You can adjust the direction of air flows entering the interior of the deflectors using the regulators. Send the air in the desired direction by moving the levers of the deflectors left-right and up-down.

Air supply through side ventilation deflectors, located on the left and right on the control panel, can be completely discontinued. In order to close or open the side ventilation deflector, turn the knob that is located on the side of the deflector.

The deflector, located on the top shelf of the control panel, can be opened or closed using a lever, which is between central ventilation deflectors.

If one of the air distribution modes is turned on or, then in the upper position, the air lever will enter the car interior simultaneously through the central and upper ventilation deflectors. To stop the air intake through the upper deflector, completely lower the lever down.

Read the same:

For the functioning of the heating systems of the cabin and air conditioning, the car engine worked. The heater uses the hot coolant of the engine for heating the air entering the interior. If the engine does not warm to normal operating temperatureIt will take a few minutes before in the salon will begin to come warm air.

In the absolute majority of cases best results Works of systems that provide a comfortable microclimate are achieved in the receipt mode into the outdoor air salon. Long inclusion of the mode recycle airEspecially with non-working air conditioner, leads to fogging glass. Therefore, it is recommended to include air recirculation mode only if necessary and for short time, for example, when driving around the terrain with a smoke or contaminated atmosphere. Once the need to insulate the interior of the car from the atmosphere disappeared, turn off the air recirculation mode.

Outer atmospheric air Enters the heating and air conditioning systems through the receiving grille, located in front of the windshield. Periodically clean the openings of the receiving lattice from the leaves and other garbage that makes it difficult to pass the air.

Car salon ventilation

2. Turn on the mode air distribution By pressing the appropriate button. Mode recycle air Must be turned off.

3. Using the fan regulator handle, set the desired level of air supply to the cabin.

POST Views: 27