Removal and adjustment of headlights on the Lifan Solano, replacement of Middle and Far Lights. Removal and adjustment of headlights on Lifan Solano, replacement of Middle and Far Light lamps Remove the headlight Lifan Solano front left

18.09.2020

Any car needs regular maintenance, including headlight adjustment, as well as their dismantling. Not exception is the Lifan Solano model, which has become quite popular in Russia.

To remove headlight headlights on Lifan Solano, you need to perform several standard actions according to a given algorithm that we now consider. But before we understand, in what situations this work may be required:

First of all, we dismantle the decorative grille of the radiator, which will allow us to get to the fastener. After that, it is necessary to remove the inner part of the front wing panel from the other side with which the headlight should be removed. Next comes the cores of the front bumper, which, also needs dismantling.

Dismantling design elements

Now we proceed to removing the headlight headlamp with a solid block. To do this, you will need to unscrew the three mounting screws, two of which are located on the top, and one on the bottom, from the wing side. Next, we carefully disconnect the bracket, there may be a little effort here. Also do not forget about electrical connectors that feed the lighting appliances. After their neat shutdown, you can proceed to the residual removal of the headlight of the Lifan Solano.

Fastening screws

Although almost all the work has already been made, there are cases when you need to get to the light bulb to replace it. Replacing Middle Lamps and far Light On Lifan Solano, the task is simple. It is necessary to remove the sealing lid from the headlight block, pulling it out throughout the perimeter. After dismantling the spring lock. Now you can reach the light bulb. Its immediate replacement is no different from the replacement of a regular lamp, so that this action does not make sense.

If the task is to replace the standard optics by Biksenon, then study the material :.

Sometimes it is necessary to remove the light bulb that indicates the rotation of the car. Her dismantling is no different from the above-mentioned actions.

Adjust headlight headlamp

Depending on the operating conditions, as well as for natural reasons, it may be necessary to adjust the front headlights of the Lifan Solano. To do this, it is necessary to prepare a car with the help of the appropriate cargo, as well as finding a suitable place with a smooth surface. As a rule, adjust the headlights is best on special stands. But you can perform adjustment at home.

Specialized equipment

Preparation

First of all prepare cars. This includes an inspection of the body and the headlights themselves for the presence of curvature, which could arise after shocks or any other deformation effects. Desirable fuel tank Fully fill the flammable to ensure optimal "waving" Lifan Solano.

Also, the manufacturer advises check the oil level and, if necessary, add it to the full level. The same needs to be done with liquid in the cooling system. After that, check the tires for the subject right level Pressure. The whole set of equipment for service, including jack, spare wheel And the tools that you take with you constantly should be in your place in the trunk. But all other items from the trunk will need to be removed, so as not to create an excessive load that is not characteristic of the normal state of the machine. Still, it will be necessary to ask a person to sit down the driver's seat. If there is no such possibility, then you can replace a person with a suitable weight.

After the actions described, we put the Lifan Solano into a fairly dark place so that the Light Light Light was clearly visible and was at a suitable level, namely on the boundary of the world. It is located in the place where the light is visible under the line, and there is no.

Remember that the car must be in a completely even position. It is about the central axis of the machine to be located 90 degrees in relation to the wall, on which the level of lighting will be performed. The distance to this wall should be exactly three meters. For accurate check The location of the machine will need to shift it up and down so that the suspension does not change its position in the future. Also, prepare a pure white sheet of paper with a size of 2 * 4 meters. It is necessary to create a light screen.

Vertically, in the center of the screen, draw the line exactly in the middle. It is necessary to make this line in the center of the axis of the car. Also, we draw a horizontal line, above which the central part of the light should not rise. In addition, there should be two vertical lines on the screen, which will indicate the central axis of headlight headlights, relative to the left and right edge. The intersection with the horizontal line should occur in the place where the central part of the headlight is located.

Direct adjustment

Adjust the headlights of Lifan Solano is not difficult. But difficulties may occur while simultaneously checking, so it is necessary to do this alternately, simply disconnecting the power, however, you can take a simple rag.

Remember that a special vinyl plastic is used as a material for making headlights on Lifan Solano, which cannot withstand high temperatures longer than a few minutes. And since the lamps can produce quite a lot of heat, then you can keep them with covert no more than three minutes in a row.

Next, for adjusting headlamps, you need the launch of the motor with maintaining the number of revolutions at the level of one and a half thousand per minute. After that, you can turn on the light on the machine to check the boundaries that should be accurately included in the sheet specified on the sheet. If you have noticed small deviations from the desired level, then you need to adjust the headlights. Its essence lies in a simple turn of the adjusting screws. One of them is responsible for the vertical axis, and the other is behind the horizontal. In case of rotation of the first clockwise, the light will be raised a little, counterclockwise - a little omitted. If you need to adjust the horizontal axis, then for this you will need to scroll the screw clockwise, which will lead to the displacement of the light beam left. After scrolling counterclockwise, the ray will be shifted to the right. For all these operations, an ordinary screwdriver is used.

Thus, adjustment of headlights for Lifan Solano may be quite an easy task for most owners of this car.

Removing and adjusting headlights, substitution of a lamp of close and distant light

In fact, at least some car needs permanent maintenance. It concerns this and headlight adjustments, also disassemble them. This approval is fair for all cars, including Lifan Solano. which has become popular with us in our country.

Removal of fleece head lighting

In order to remove Lights head lighting Lifan Solano, you need to perform several standard actions on this method, which we currently see. Situations in which it may be necessary to remove the headlights for the purpose of its disassembly or detecting a malfunction:

To begin with, it is necessary to dismantle the decorative grille of the radiator, which will allow us to get to the fastener mechanism. After which you need remove the inner part of the front wing panel from the other side with which it should be removed headlight. Next comes the cores of the front bumper, which, also needs dismantling.

We carry out dismantling of design elements

Now you can proceed to the direct removal of the entire headlight headlamp with a solid block. In order to do this, you will need to unscrew the three mounting screws, two of which are located on the top of the headlight, and one on the bottom, from the wing side. Next, we carefully disconnect the bracket, for which a small effort may be needed. Also, you do not need to forget about electrical connectors that feed on the lighting appliances. After their neat shutdown, you can proceed to the residual dismantling of the headlights.

After dismantling the elements of the body, you can proceed to the dismantling of the headlight itself

Despite the fact that, almost everything, work has already been made, there are cases that it is necessary to get to the label to replace it. Replace the Lifan Solan's Middle Lights Lights is a fairly simple task. To do this, it will be necessary to remove the sealing cover from the headlight block by defining it throughout the perimeter. Next, there comes the queue of the spring retainer, after dismantling which it will be possible to reach the very light bulb of the near light. Its immediate replacement is no different from the replacement of a regular lamp, so that this action does not make sense.

If you are faced with the task of replacing the standard optics by Biksenon, then study the material: we install Bixenon in the headlight with your own hands.

If you are faced with the task of replacing a long-lit lamp, then it will be necessary, after pre-removing the sealing cover, the same remove Spring locking mechanism, which will allow us to get to the lamp. Its replacement occurs on the same principle.

Also, sometimes it is necessary to remove the light bulb that indicates the rotation of the car. Her dismantling is no different from the above-mentioned actions to replace the rest of the lamps. After that, it will be necessary to collect the entire design back and install the headlight block into place.

Adjust headlight headlamp

Depending on the operating conditions, as well as for natural reasons, it may be necessary to adjust the front headlights. For this, it will be necessary to prepare a car with the help of appropriate cargo, as well as finding a suitable place for this with a smooth surface. As a rule, adjustment is best on special stands that allow you to easily implement this difficult task. However, you can perform adjustment at home.

Lifan Solan's headlights

We restore the transparency of the head Lifan Solana.

Replacing Middle Lights on Lifan X60

Description.

only specialized equipment will allow adjustment in the best possible way.

Preparation

The first point can be considered the direct preparation of the car. This set of actions includes an inspection of the body and headlights themselves for the presence of curvature, which could arise after shocks or any other deformation effects. It is desirable that the fuel tank be fully filled with flammable, in order to ensure optimal "waving" cars.

Also, the manufacturer advises check the oil level and, if necessary, add it to the full level. The same, you will need to do with liquid in the cooling system. After that, check the tires for the correct pressure level. The whole set of equipment for car service, including a jack, a spare wheel and tools that you take with you constantly, should be in your place in the trunk. But all other items from the trunk will need to be removed, so as not to create an excessive load that is not characteristic of the normal state of the car. Also, you will need to ask a person to sit on the driver's seat. If there is no such possibility, then you can replace a person with a suitable weight.

Now it has come to the cerebral preparation to all further actions. They include the supply of cars in a sufficiently dark place so that the Light Light Light is clearly visible, and was at a suitable level, namely on the boundary of the world. It is located in the place where the light is visible under the line, and there is no.

you can use the garage door or the house wall

Remember that the car must be in a completely equal position. It is about the central axis of the machine to be located 90 degrees in relation to the wall, on which the level of lighting will be performed. The distance to this wall should be exactly three meters. To accurately check the correctness of the machine, it will be necessary to shift it up and down so that the suspension does not change its position in the future. Also, prepare a pure white sheet of paper with a size of 2 * 4 meters. It is necessary to create a light screen.

Vertically, in the center of the screen, draw the line exactly in the middle. It is necessary to make this line in the center of the axis of the car. Also, we draw a horizontal line, above which the central part of the light should not rise. In addition, there should be two vertical lines on the screen, which will indicate on the central axis of headlight headlights, relative to the left and right edge. The intersection with the horizontal line should occur in the place where the central part of the headlight is located.

Direct adjustment

Adjust Lifan Solano headlights are not difficult. To begin with, you need to know that checking the headlights can be very difficult at the same time. Therefore, it is necessary to do this alternately, simply disconnecting the power of the headlight, which is currently not checked. However, it is possible to use this and a simple cloth, which is covered inactive headlight. Nevertheless, it must be remembered that a special vinyl plastic is used as a material for the manufacture of headlights, which does not withstand high temperatures longer than a few minutes. And since the headlight lamps can produce quite a lot of heat, then you can keep them with no more than three minutes in a row. After a few minutes of cooling when the light is turned off, the operation can be repeated.

The second point in the list of our actions on adjustment will be the launch of the motor with maintaining the number of revolutions at the level of one and a half thousand per minute. Now you can turn off the headlights of the headlight to check the boundaries of light, which should surely go into the boundary specified on the sheet. If you have noticed small deviations from the desired level, then you need to adjust. Its essence lies in a simple turn of the adjusting screws. One of them responds to the vertical axis, and the other is behind the horizontal. In the case of turning the first of them clockwise, the light will be raised a little, counterclockwise - a little lowered. If you need to adjust the horizontal axis, then for this you will need to scroll the screw clockwise, which will lead to the removal of the light beam to the left. After scrolling counterclockwise, the ray will be shifted to the right. For all these operations, an ordinary screwdriver is used.

Thus, adjusting the headlight light Lifan Solano. It may be quite an easy task for most owners of this car.

POST Views: 5

Usually new car serve u official dealer, hoping not to lose guarantees. And only after its end, the owners are taken for the tool or seek the master with adequate rates - the desire to pay less for uncomplicated, in general, work is quite justified. But it seems that the newly new owner "Solano" will refuse the services of the officials much earlier.

It is enough to carefully examine the warranty contract: it does not apply to many parts, it does not apply at all, and a year later, a more extensive list is added to this list - not fit for a reversal of the service book. Moreover, the grooves, dustners, gaskets, brushes of electric motors and other trifles, which constitute an integral part of complex nodes and aggregates. Who like, and we do not need such a guarantee! To serve the editorial "Solano" will be on their own.

Faculty of Hydraulics

Raising the focus of the hood, hold the plastic holder, appearing from above the finger on the console part. Otherwise, the sloping item will easily burst, especially in the frost. The same when installing back: hold the holder from the bottom. To replace oil in the engine weakening the key "on 13" two front and completely unscrew the two rear bolts of protection motor compartmentAfter that, pulling back, remove it.

Although to access drain plug (turnkey "on 15") is provided with a plug, to oil filterwithout removing the protection, you can't pick it up anyway. If the filter does not go from hand, we call for the help of the puller cup. A three-pailed "crab" is suitable, but there is nothing to do with a chain puller - there is no place for maneuver.

The oil has to be poured with a thin flower: a huge look at the neck at the bottom becomes a needle ear, under the pressure of the excessable air, a wide jet is sprinkled. Here, perhaps, the most significant remark about this operation.

To drain the antifreeze in the left tank of the radiator, a plug is provided, and it is great. Just do not twist it completely, otherwise the flow will go into two jets and catch it will not be easy. Mix better hot liquid (so that the thermostat is open) - do not wonder!

The gur of the rules is changed after 80 thousand km, but most likely will have to do it before. On our car, for example, a pipeline was bursting a pipeline ( SP, 2011, № 10), And now we found flowing in the subframe area - because of poorly tightened clamps on a short hose connecting two tubes. We strongly recommend that you check this connection.

In general, the hydraulic strollers are laid here carefully: the head branch of the Gur is clearly lacking length, therefore it is quite likely that it will burst again. With brake pipes, the situation is no better: completely and relate to each other (especially in the ABS block zone), which is unacceptable - over time they will probably respond.

The hoses on the rear wheelchairs were twisted, because of this, it was not possible to raise the bracket to replace the pads. Fuel filter It is connected to highways not with threaded couplings or quick-consuming tips, but by conventional hoses, compressed ancient clamps - such a connection is perhaps no longer used on any machine. Of course, we corrected that we were able to: brake tubes Went, the hoses straightened and installed a pair of powerful clamps for each fitting or tube. Is it just to do this to the buyer?

Theormrats.

To replace the front pads, you will need two keys "on 14", one of them with narrow sponges to hold the fingers of the guides. The bracket-firing of the marginal wear should be on the inner block on top. The rear mechanisms are located in the same way, but the bolts of the turnkey guides "at 17". Tightening torque of wheel nuts 120 N. m. If the handbrake cable deteriorates, suffer: to sew the adjusting nut will have to, removing the floor tunnel overlay. And for this it is necessary to take over the Police: Remove the plank under the tree on the instrument panel, the heater control unit, the ashtray, finally, the tunnel lining itself with the armrest.

At each stage, surprises are waiting for you: then you need a very short cross screwdriver, then there is not enough full-time pistons, then we will challenge fasteners from the tool into a narrow place (therefore in advance of a powerful magnet). Of course, you can simply turn out two bolts on the bottom of the armrest box and, by shifting it to the right, bend the gum with a screwdriver at the base of the lever. So much faster you can bring to nuts - adjusting and touching, but this is still a barbaric method - scratches on the plastic will be for sure.

With the replacement of spark plugs (they are turnkey "on 16") and air filter We managed without special problems. By the way, the filter is suitable from Toyota-Corolla model E12 (previous generation).

The belts of mounted units on the LF481Q3 motor as many as three! And for each eye and the eye, since the actuator scheme, gently say, confused. The work of the Gira pump depends on the reliability of two belts at once - its own, connected to the pump pulley, and the generator, the very pump of torque. In addition, there is no automatic tensioners anywhere, and without them (and without due experience) is easy to make a mistake with the belt setting. If you are not shifted, they will slip, but you will pull it - you will kill bearings.

Replacing the timing of the timing better to trust the specialists, because it is more difficult to change the belt with a roller on the "Lifan". It is more difficult to remove the valve lid, right support power aggregate And, hanging the engine, unscrew the crankshaft central bolt, usually tightened.

Electrical engineering

About the replacement of light bulbs in the manual for no word. Perhaps the manufacturer believes that they are eternal? As if not like this: on our car, the Middle Light in the right spotlight went out 10 thousand km after purchase. Remove the fire (H1) It turned out to be easy: picing up the slotted screwdriver of the casing of the section of the section and withdrawing it out of the groove at the bottom of the headlight, removed and postponed the lid aside.

Well in moderation is wide, but as deep. However, it was possible to remove the spring bracket with the lamp. But put in place new is not so easy. First, there is no clear key in the nest to orient the lamp in the only correct position (the plus connector vertically, the mock on the base up-left, if you look at the front head). Secondly, hold the lamp and fix the bracket at the same time it is not easy - the lamp comes out of the nest, then the bracket is flushed. In general, I had to tinker.

Removal and adjustment of headlights, replacement of the Middle and Far Light lamps

Almost any car needs regular maintenance. It concerns this and adjusting headlights, in addition to their dismantling. This approval is fair for all cars, including Lifan Solano.which has become quite popular with us in the country.

Removal of fleece head lighting

If you put a goal remove Lights lifan Solano HeadlightIt is necessary to perform several standard actions according to a given algorithm that we now and consider. Situations in which the headlight will be removed pursuing the purpose of its disassembly or detecting a malfunction:

First of all, you need to dismantle the decorative grille of the radiator, which will allow us to get to the fixing mechanism. As a result, it is necessary remove The inner part of the front wing panel is from the other side, with what) (the headlight can be removed. Next comes the cores of the front bumper, which also needs dismantling.

We carry out dismantling of design elements

Now proceed to the immediate removal of the entire headlight headlamp with a solid block. To be able to do this, you will need to unscrew the three mounting screws, two where they are located on the top of the headlights, and one - on either the top, not familiar wings. Next, we carefully disconnect the bracket, for what purpose it takes a slight effort. Also, you do not need to forget about electrical connectors that feed on lighting devices. After their accurate shutdown, proceed to the residual dismantling of the headlights.

Read the same way

After dismantling the elements of the body, proceed to the dismantling of the headlight itself

Contrary to the fact that everything, the work has already been made, there are cases that you need to get to the light bulb to replace it. Replace the Lifan Solan's Middle Lights Lights is a fairly simple task. For this purpose it will be necessary remove From block head lighting Sealing lid, pulling it around it throughout the perimeter. Next, the queue of the spring retainer comes, after the dismantling of which can already reach the very light bulb. Its immediate replacement is no different from the replacement of the ordinary lamp, so it is not advisable to describe this action.

On the contrary, it is worth a task to replace standard optics by Biksenon, then study the material: I install Bixenon in far Alone.

On the contrary, you have the task of replacing the lamp of the far light, it will be necessary, after pre-removing the sealing cover, it is also possible to remove the spring locking mechanism, which will allow us to get to the lamp. Its replacement occurs on the same principle.

Also, when you need to remove the light bulb indicating the car rotation. Her dismantling is no different from the above-mentioned actions to replace the rest of the lamps. Subsequently, you need to assemble the entire design back and install the headlight block into the area.

Adjust headlight headlamp

Stripping from the operating conditions, and besides the state of health, the front headlight adjustment will be required. For this purpose, you need to prepare a car in the presence of appropriate cargo, additionally finds you a suitable place for this purpose with a smooth surface. You, carry out the adjustment much better at special stands, allowing without much effort to implement this difficult task. Those of the two, perform the adjustment there is an option and at home.

Disassembled headlights Lifan Solana!

We restore the transparency of the head Lifan Solana.

only specialized equipment will allow adjustment in the best possible way.

Preparation

Read the same way

you can use the garage door or the house wall

Remember that the car must be in a completely equal position. It is about the central axis of the machine to be located 90 degrees in relation to the wall, on which the level of lighting will be performed. The distance to this wall should be exactly three meters. To accurately check the correctness of the machine, it will be necessary to shift it up and down so that the suspension does not change its position in the future. Also, prepare a clean white sheet of paper with a size of 24 meters. It is necessary to create a light screen.

Vertically, in the center of the screen, draw the line exactly in the middle. It is necessary to make this line in the center of the axis of the car. Also, we draw a horizontal line, above which the central part of the light should not rise. In addition, there should be two vertical lines on the screen, which will indicate on the central axis of headlight headlights, relative to the left and right edge. The intersection with the horizontal line should occur in the place where the central part of the headlight is located.

Direct adjustment

Adjust headlights Lifan Solano. not difficult. To begin with, you need to know that checking the headlights can be very difficult at the same time. Therefore, it is necessary to do this alternately, simply disconnecting the power of the headlight, which is currently not checked. However, it is possible to use this and a simple cloth, which is covered inactive headlight. Nevertheless, it must be remembered that a special vinyl plastic is used as a material for the manufacture of headlights, which does not withstand high temperatures longer than a few minutes. And since the headlight lamps can produce quite a lot of heat, then you can keep them with no more than three minutes in a row. After a few minutes of cooling when the light is turned off, the operation can be repeated.

POST Views: 6

Similar articles: