Remove the spare wheel of Chevrolet Captive. Installing the mount for a spare wheel
Outlet under the bottom
The report was: KZ-2.
The topic of discussion on the forum:
1.5 months ago, I ordered a frame under the splash and components. Triced with the number, allegedly accommodating full-size. But in the end, it came under the spare tack of originally under 16 inch wheels 215/75 / R16. The rooms have a bracket 2, and the option is one, as explained that simply obsolete number was replaced. Obviously, it is possible to put in this frame as such as such, so it is full-size on 16, which now go from the factory.
Immediately, I followed the 18th wheel, it can be seen that height is great. It can be pressed and it seems almost everything is good, but on the car it's hands no longer do. At first I thought to cut and extend, but then I found a plate in the garage with already the necessary sizes (pieces of cars When the doors are twisted with the wire, it can be seen as a spacer) .2mm it seemed thin, so two for each side decided to put it. In general, it came well.
The frame on the car got up of course without problems, but everything is fixed the rest of the vacant sweat. On 18 wheezing is quite heavy, shoved. He began to start a hook, and he does not climb, prevents the tires, 5 mm was lacked. I looked at what I saw that I saw that the tire was a little resting in my podchil plates. He changed the situation. As a result, he took off the hook with a bolt, hooked behind the frame, and then his friend screwed it. However, in general, it was not really hard to put a mud.
But the most important thing is that the reserve is not in the trunk. It is easy to make it, and there, if I got, then you will have to smear and so on.
"Recently, a rather unpleasant story happened to me. I went to the relatives and at night at half the way I had a wheel, I had to make an emergency replacement in place. It's good that I always have tools with me, but it would be so nighting on the track , and there anything happens. I stopped near the service, but the tire unit was not here.
Ride on the dock - that still flour. It is impossible to accelerate the sensitivity and the car woves as a pregnant cow on the ice. As soon as I came home, immediately began to think about that. How to make an attachment for a normal full-size spare wheel. W. official dealer Nothing like that was not available, I had to search on the Internet and at the next forum I finally found what I was looking for - an alternative mount for a full-sized spare wheel. Everything you need ordered on one site, began to wait. On another site, I encountered an equally interesting offer. After a couple of weeks, I took the box from the post office, inside which was bracket.
The installation process is simple to impossible. You need to fasten this most bracket to the body into four nuts, while you do not need to remove the silencer, as I thought before. True, if you, too, decide to do the same, then work better with the assistant, and then one is very uncomfortable. After installing the bracket insert the hook into the technological hole in luggage compartment, I put a spare wheel and planted a hook to the bolt. Especially for this, I did not buy a new wheel, I decided that the winter will serve in winter summer wheelAnd in winter - winter.
It took about half an hour to work, but I am now sure that in case of trouble with the wheel, I can make a replacement without any problems and continue the movement in the previous rhythm. After a while, I noticed that the dirt accumulates in the spare time and it is not surprising, because it is almost on the bottom of the car. In order not to spoil her species, I ordered a rubber case, there splash and wander. The bracket along with delivery cost me 4.5 thousand rubles. Yes, not so cheap, but it is worth it. "
1. To open the plug over the rear bumper, use a slotted screwdriver
2. Using a balloon key Loosen the bolt fixing the spare wheel
3. Disconnect the mounting cable of the spare wheel under the rear bumper
4. Remove the spare wheel
In order to avoid the appearance of an extraneous noise while driving a jack and other tools should be put under the floor of the luggage compartment.
Characteristics of jacks - Limit workload: 900 kg
This jack was designed specifically for this model of support.
Use it for other car models is not recommended.
When working with a jack, it is impossible to exceed its maximum permissible load.
The use of this jack for other cars can lead to its spoilate or vehicle breakdown, and also cause
injuries.
Safety measures when replacing the wheel
1. Turn on the emergency light alarm.
2. Park the car at a sufficient distance from the main movement.
3. Parking should be made on a smooth and solid ground.
4. Turn off the engine and remove the ignition key.
5. Install the parking brake.
6. All passengers must leave the car's salon and move away from it to a safe distance.
7. Under the wheel, located diagonally relative to the replaceable wheel, lay the wedges on both sides, wooden bars or large stones.
The car raised on the jack loses its stability, which can cause damage to the car and cause corporate damage.
You should use only the delivered jack installed in the correct position.
Jack must be installed perpendicular to the soil
It is impossible to be under the car mounted on the jack.
You can not run the engine of the car standing on the jack.
The jack must be used only to replace the wheels.
Do not lift the car by jack on inclined or slippery surfaces.
The jack should be installed directly near the wheel, which must be replaced.
Temporary spare wheel (dance) is intended only for short-term use. At the first opportunity, contact your car service techniques to replace the temporary spare wheel as soon as possible.
Failure to comply with these safety rules can lead to the fact that the car will slip from the jack, and this in turn can
Cause serious injuries.
