Alteration ZIL 131 on diesel. Re-equipment ZIL on diesel
Our company has extensive experience in converting cars ZIL on diesel fuel. Re-equipment trucks ZIL allows you to increase the permeability, efficiency and environmental friendliness of trucks. The company makes the installation of more modern diesel engines D-245.9, MMZ D-245.12C and other engines from this family to various modifications of Cars ZIL-130 and ZIL-131.
Specificity re-equipment of cars ZIL on diesel Our company is as follows.
Our experts will take you and install the engine to your car for two or three days at the location of your enterprise;
The modern engine D-245 is very economical in terms of specific fuel consumption. Thanks to modern design improvements, it was possible to achieve a smaller consumption than the usual, standard gasoline engine. For operation on the Big Claus, which is characteristic of Russia, a special engine and fuel heating system is used.
If you order re-equipment of cars ZIL on diesel Here, here it also includes the cost of all necessary documents to legalize the engine replacement.
The gearbox will remain the same as it was before replacing the engine on your car.
You get a guarantee in our center. By registering, you get the right to warranty repair and scheduled maintenance. At the end of the guarantee, you will benefit to us if you need post-warranty engine repair in Yaroslavl, since the map of your engine will be kept on our company, which will help in the future to prevent emergency situations and make it possible to replace the parts in time. Additionally you get the opportunity overhaul Engine.
We always have a sufficient range of spare parts for diesel engines type D-245.
If you order, our specialists will help you in the process of registration in the traffic police;
D-245 diesel engine has a greater power compared to gasoline engine normal configuration, which allows you to take any lift in difficult weather conditions in winter. It has greater reliability and service life.
Dr. D-245 engine is estimated as not difficult for maintenance and repair;
Contact our company, re-equipment of trucks ZIL - Our specialization.
Engine for re-equipment of cars ZIL-130 and ZIL-131 on diesel fuel
For re-equipment ZIL-130 and ZIL-131 on diesel enginesThe engines of the D245 family are used. For example, the engine is often used D245.9E2-216, designed for this. This engine is the development of the Minsk Motor Plant. Diesel engine d245.9e2-216 is four-stroke engine liquid coolingCertified according to Euro-2 standards. The engine can be operated normally at air temperature from -45 to 40 degrees Celsius.
Result re-equipment of cars ZIL-130 ZIL-131 on diesel engines is the savings of the motorist. Fuel consumption plus diesel fuel is cheaper.
Saving from converting cars ZIL-130 ZIL-131 on a diesel engine with gasoline, provided that the car passes 100 km a day per year is more than 150 thousand rubles.
Re-equipment of zila and gas on the engine D245 on diesel fuel
Specialization of our company -. Compared with regular gasoline engines, type D-245 engines has a smaller specific fuel consumption. For refitting ZIL, the diesel gas is used by the D245 family engines, which was developed on the Minsk Motor Plant. Designers managed to improve the engine in such a way that the fuel consumption fell twice as compared with the usual gasoline engine. It is possible to operate the engine at air temperature from -45 to 40 degrees Celsius. For operation on the Big Claus, which is characteristic of Russia, a special engine and fuel heating system is used.
If you want to re-equipment ZIL at d 245 Engine, contact our company. Our specialists will hold a qualitative re-equipment of ZIL on the D245 in a very short time at the place of your car. For re-equipment, kits made in factory conditions are used, in accordance with the technical documentation. Only components of excellent quality are used. We have a large range of spare parts for diesel engines type D-245.
If you decide to order re-equipment ZIL gas for diesel fuelYou also get a set of all necessary documents to legalize the engine replacement that is included in the cost of work.
Moreover, re-equipment ZIL at d 245 The engine is considered not difficult for repair and maintenance.
After re-equipment of your car, you get a guarantee in our company, the right to scheduled maintenance of the car. When the warranty is over, we will have the map of your engine and you can contact us for post-war repair.
In accordance with technical Regulations "On the requirements for automotive gasoline" approved by the Government Decree Russian Federation No. 118 of February 27, 2008 Since 2011, the production of 76th gasoline ceases in Russia. Re-equipment ZIL on diesel is one of the solutions to the further operation of cars using 76th gasoline. .12С-231 and its modifications are specifically designed for re-equipment motor vehicles on the basis of ZIL-130 and ZIL-131, with gasoline DVS - Diesel. This unit was developed by the designers of the Minsk Motor Plant for installation on Cars ZIL instead of a regular gasoline engine.
Specifications of diesel engine D-245.12S-231:
The location and number of cylinders ........................ 4l;
Power kW (hp) .......................................... .... 80 (108.8);
Maximum torque N / M (kgC / m) ......... 353 (36).
The purpose of re-equipment for diesel is a significant cash saving of the owner vehicle Associated with operational costs of the car. Savings is as follows:
- a significant reduction in fuel consumption by the engine (twice);
- The cost of spare parts for d-245 is lower than for the standard ZIL-130 motor.
Examples of cost reduction:
Petrol:
Cost (rubles):
new engine - 360,000;
cylinder head heads - 2 to 30 000;
crankshaft shaft - 47,000;
Fuel consumption (l / 100km) - 38.
Diesel engine D-245.12C:
Cost (rubles):
new engine - 280,000;
cylinder heads - 25,000;
crankshaft shaft - 25,000;
Fuel consumption (l / 100km) - 18.
(Prices are relevant for the first quarter of 2016)
The cost of working on the conversion of the vehicle by our car service - 50,000 rubles. At the end of the work we give the owner all required documents For registration in the gibdd, passport and warranty documents on new engine. For improvement sound characteristics Car ZIL can be replaced by a standard shifting gearbox. The cost of the replacement of the PPC ZIL in our car service within 6000 rubles, and depends on the modification of the vehicle.
A wide range of services provided by our auto service allows you to make the necessary regulations with the modernization, as well as the current repair work. New diesel engine - New life of your car.
Re-equipment ZIL on diesel today is saving your money tomorrow, start saving today, the benefit from re-equipment is obvious.
2 stove transient zil bull
3 Clutch hull
5 Transmission
6 release bearing
7 clutch disc
8 clutch thrust
10 steering mechanism
11 Power system
12 ZIL-130 per 24 volt
14 Gas thrust
15 Systemcooling
To install the engine on the ZIL-130 car, you will need the engine itself. It can be bought in the store agricultural machinery. The most important thing is that the document is on this engine, a certificate of an account with a car installation, and not on the tractor, otherwise you do not form it in the traffic police. Help account with installation on the car is coming Green, and on the red tractor, so do not confuse.
Engine D-245 MMZ is designed to re-equip the ZIL-130 cars, ZIL-131. This model The engine is equipped; generator, oil filter, gear pump, tractor production turbocharger, exhaust pipe, air filter assembly with rubber pipes, cooling fan with drive belts, Production compressor Belarusian. Engine equipped fuel pump high pressure Production »MotorPal. There is also a starter. Carter clutch and adhesion itself. Petal, basket of STK. Intercooler for cooled air supply to cylinders for greater compression.
2 stove transient zil- bull
The engine mounting plate is placed at the factory, also sold in the store. Such a stove is placed on the car ZIL bull, and not to the tractor, they do not confuse different. If you want you can make it yourself. To do this, you need a sheet of thick metal 10-12mm and a sample of the factory plate. By sample, the main thing to drill all the holes accurately and cut down the contour and the stove is ready.
3 Clutch hull
The clutch case will remain native from your car. It will need to make holes for the mounting bolts to the engine. Cut under the starter under the big if you put, and if you put a little Czech, then it is not necessary, the Czech starter does not prevent anything a good option And the casing will be the whole and the starter will stand easy and will not break the stove adapter.
The front mounting of the engine will have to do. On the Internet there are many options how to make a mount. I cut the fastening from thick metal and put it on the rubber lining to the car's frame on the bolts. Picked up two tubes and substituted for native mounting through the bolts as shown in the photo. You can do it at your discretion.
After you install the engine on the car, you need to make the following changes.
5 Transmission
In the gearbox you need to make a change in the primary shaft. The primary shaft will need to give to the current so that it rooted the spout of the primary to 2 cm in the machine or your gearbox will not enter the clutch.
6 release bearing
The release bearing is best to put from the tractor T - 40 as I did. Such a bearing goes very long been tested by time. Next, you need to come to it be sure to lubricate the bearing with lithol, as I have done from me. You can leave your bearing at your discretion. You can lubricat at any time released Bearing And he will serve for a long time.
WATCH THE VIDEO
7 clutch disc
The clutch disc is from the car KAMAZ. On this disk I have already departured for many years and to this day I do not change. The KAMAZ disc clutch is made on a lot of stronger Zilovsky. The engagement of the primary and the disk slots are enough for full-fledged work, although he gears in the floor of the primary shaft tooth. Watch the video there everything is shown.
WATCH THE VIDEO
8 clutch thrust
Clutch thrust will not work as it lacks the disk outlet. To do this, do the following. To the clutch lever you need to weld the extension cord with holes for larger move Traction as shown in the photo. After this operation, you will try the holes in the holes of the clutch how to work by rearring the craving. I have a clutch basket from the tractor native. If you have a basket of ZIL, it may not be necessary to lengthen the craving.
WATCH THE VIDEO
If you want to leave the compressor native D-245, but it has a minus, it is very noise and knocks on the brains, shakes slowly since it is single-cylinder. I suggest you best put the compressor from the car ZIL. It is not heard as it works, and shakes 2 times faster. For reworking the compressor, you will need to make a stove for fastening the compressor and pull the pulley for the drive from the engine. All these materials are on this site, as well as watch the video, as I redo.
WATCH THE VIDEO
10 steering mechanism
WATCH THE VIDEO
On the engine D-245 there is a NSH pump for this, this is already good, here you will need talek from the steering mechanism ZIL, hydraulic hoses, hose fittings. There is a video footage You can see how everything is done. Watch the video.
11 Power system
I made small changes to the system. From the fence there is a fuel supply to a coarse filter, then the pump pump, with a pump on a fine cleaning filter and a high pressure pump. Changed here the fuel return is made on the KAMAZ car. A tee is delivered and from the pump TNVD there is a return to the tank. See the photo.
12 ZIL-130 per 24 volt
Electrical system. By car ZIL-130 diesel is best done for 24 volts. For one important reason that in winter it will be easier for you to make a car. 12 volts will be weak. To do this, you will need new generator on 24 volts, all 24 volts light bulbs. Starter for 24 volts (better put Czech gear), temperature sensor, ammeter leave the same.
WATCH THE VIDEO
Air filter Need to be transferred to the cab. By connecting it with a corrugated hose. Because under the hood from him there is a lot of noise in the cockpit and ride hard with noise, when there is nothing to hear. He was postponed for the cabin, I calmly talk on the phone, everything heard. There are not much remakes here but it costs it.
WATCH THE VIDEO
14 Gas thrust.
You will have to make a gas pedal thrust yourself that you have enough fantasy. It is done in me as shown in the photo. You can make it at your discretion. There is also an option you can make a craving through a cable with a shirt, as is done on the Zhiguli. In this embodiment, there is a plus that when the engine shifts the turnover, it will not change it, since the engine in front of braking in front and back, you will not notice, and the engine turns will change.
WATCH THE VIDEO
15 cooling system
In the cooling system there will be some changes in the connections of the nozzles with the radiator. The nozzles of the radiator and the engine of different diameters should you need to choose them in the store. Now there are nozzles with different diameters on the tips, so that you can pick up and all join the photo as I did.
WATCH THE VIDEO
