Oil for Skoda Yeti 1.2. Automal and all you need to know about motor oils

A small Family SUV of Yeti from Skoda was presented at the exhibition in Geneva in 2009 and became the first representative of this class in model row Autocontrace. The new product built by the Volkswagen A5 platform (PQ35) received a large spacious interior, high-quality finish and a comfortable high fit. On the domestic market Dorestayling Yeti (2009-2014) was supplied in a complete set with gasoline and diesel power plantsWorking in a pair with a carton-machine or mechanics. Working volumes of the first: 1.2, 1.4 and 1.8 liters (105, 122 and 152 hp), and a all-wheel drive diesel engine - 2.0 liters from 140 hp In the asset. What the economy is swinging, then the winner was 2.0 TDI with its 6.5 liters per 100 km in a mixed cycle, but according to the dynamics, the championship belonged to a 1.8-liter motor on full drive - 8.7-9.0 seconds before the first hundred. Information about the types of oilfilled oil and how much to pour it, then in the article.

In 2013, an updated Yeti appeared in the Frankfurt Motor Show before the public. Among the differences from the predecessor, an improved interior, converted design established by electronic assistant Parking, new radiator grille and bumper, as well as the best technical equipment. The SUV retained the PQ35 basic platform and the same dimensions. Motor gamma varied depending on the target market. If we consider Russia, then here Skoda Yeti. Sucked with three engines. The first is 1.6-liter gasoline with distributed injection (110 horses, about 7 liters of mixed consumption per 100 km and acceleration to 172-175 km / h), the second - 1.4-liter gasoline TSI (125 horses, 6 liters of consumption and speed 186- 187 km / h), the third is also TSI, but with a volume of 1.8 liters (152 horses, consumption of 8 liters and a limiting speed of 192 km / h). Motors are aggregated robotic box, machine or mechanic.

Generation I (2009 - N.V.)

Engine CBZB 1.2.

• How many litters of oil in the engine (total volume): 3.6-3.8 liters.
• When changing the oil: 15000

Engine CAXA 1.4.

• What engine oil is poured from the plant (original): Synthetic 5W30
• Types of oil (by viscosity): 5W-30, 0W-30, 0W-40
• How many litters of oil in the engine (total volume): 3.6 liters.
• Oil consumption per 1000 km.: Up to 300 ml.
• When changing the oil: 15000

The engine on the Skoda car over time is subjected to wear and deformation. To prevent this process, it is necessary to competently select engine lubricant according to tolerances and specifications from the manufacturer. High-quality oil will not only provide the functional performance of the system, but also protects it from damage.

What tolerances on Skoda different models

Skoda Rapid

Czech manufacturer Indicates a lubricant VW Long Life III lubrication with a viscosity of 5W30 for models Skoda Rapid With power and volumes of engines:

• 122 hp TSI - 1.4 l;
• 86, 105 hp TSI - 1.2 l;
• 105 hp TDI - 1.6 liters.

For more powerful power units, the manufacturer recommends the VW Special Plus 5W40 oil. His poured B. atmospheric enginesmounted on rapid.

At factory B. new carThe conveyor released from the pipeline lubricant Volkswagen with tolerances 502 and 504. When performing, experts can offer auto-oil with other specifications and tolerances. For example, in Skoda service centers can offer oils from brands Shell, Mobile or Castrol.

Skoda Octavia

IN power units Octavia A5 The manufacturer recommends floating products on a synthetic basis. As for tolerances, they must comply with the standards of VW 502/504/505/507. Viscosity - 5W40, 5W30. However, when performing, the 0W30 lubricant is poured. Car enthusiasts prefer:

• Motul 8100;
• Castrol EJ;
• Shell Helix ultra;
• We are sitting about;
• X-wedge;
• Liquida moth.

• TDI 2.0 - 3.8 l;
• TDI 1.9 - 4.3 l;
• TSI 1.8 - 4.6 liters;
• TDI 1.6 - 3.8 l;
• MPI 1.6 - 4.5 liters;
• TSI 1.4 - 3.6 l;
• TSI 1.2 - 3.6 liters.

According to technical regulation, the oil change is carried out after 15 thousand km of mileage or earlier, depending on operational conditions.

Octavia 7.

In the instruction manual, it is indicated that for cars with a flexible replacement interval, it is necessary to pour oils with VW 504 tolerances if the engine has a volume of 1.2-1.4-1.8 liters and is equipped with a turbine.

In turbocharged engines with volumes of 1.6 and 2.0 per diesel fuel It is recommended to fill VW 507. If a limited interval is installed on the car, then for gasoline DVS Suitable lubricants with tolerances 502.

Czech manufacturer fills in cars by default Skoda Octavia. 7 Castrol EDGE 5W30 oil. It corresponds to the tolerances of Long Life III, which may be indicated on the canister together with specifications from Volkswagen.

After passing, the car enthusiasts prefer to change the branded lubricant on alternative analogs from manufacturers:

• Mobil;
• Shell;
• Motul.

The viscosity index is selected based on the operational conditions and temperature indicators of one or another region.

Speaking of replacement periodicity, it is necessary to proceed from the tolerances used. It is best to replace the car to achieve 10-15 thousand km of mileage.

Volumes of filling fluid in motors:

• TSI 1.2-1.4 - 4.2 l;
• TSI 1.8 - 5.2 liters;
• TDI 1.6-2.0 - 4.6 liters.

Oktavia tour

The replacement interval for OTC systems Octavia TUR is from 10 to 15 thousand km, depending on the operating conditions. The manufacturer recommends a synthetic-based lubricant with an index 5W30 or 5W40 depending on the parameters and volume of the engine.

The amount of oil poured is up to 5 liters. As for tolerances, the product must correspond to the VW 503-504. More than old versions of VW 501-502 may also be suitable.

Skoda Superb

Volkswagen Automotive Concern uses factory oil on a synthetic-based 5W30 for ICE systems Skoda Superb.. It corresponds to the tolerances of Long Life III VW. This almost the same lubricant as Castrol SLX. In the service centers in the motors pour lubricant on the synthetic database from the producer of the shell.

You can pour the car and from other manufacturers. The main indicator is the compliance of the tolerances of 502-504 and the viscosity classes of 5W40, 5W30. Also, do not forget about the periodicity of the oil replacement recommended for the engine systems equipped with turbocharging. If the superb model has 2.0 TDI engine, then it is better to use the 5W30 crawler with a tolerance of 507.

Lubrication with VW 504 tolerances must be used when running 15 thousand km. Some car enthusiasts prefer to replace the replacement after 10 thousand km. The regulation allows an earlier replacement if the car is operated in harsh climatic conditions.

Tolerance Skoda Yeti

For the power units set on Skoda Yeti, the original grease GM DEXOS 2. It corresponds to the tolerances VW and LL. The packaging indicates the following tolerances:

• VW 504;
• VW 501;
• VW 502.

In service centers for atmospheric systems internal engineering 1,6 MPIs operating on petrol fuelUse Shell Helix or EJ Castrol with 5W30 viscosity indices. Such power units correspond to the tolerances VW 502/504/505/507. Experts also offer to fill motor lubricants From manufacturers:

• Motul 8100 5W40;
• Total 9000;
• Liquida moth.

Staying on the selection, special attention should be paid to specifications and viscosity. Usually for skoda engines Yeti uses 4 liters. Replacement is performed based on climatic conditions. Recommended frequency - 10-15 thousand km run.

Oil in the engine system Skoda Fabia

Motor liquid on the model Skoda Fabia. Must be to admit the VW 502-505 and the degree of viscosity of 5W40 or 5W30. Recommended Castrol EDGE.

You can also pour the compositions on a synthetic basis with the viscosity index of 0W30. In service centers, Skoda, specialists use such oil for Fabia with an engine capacity of 1.4.

It makes no sense to overpay the station workers maintenance For the planned replacement of engine oil and related filters. It is enough to do this not a tricky work once and next time you will already be a specialist. And we will certainly help you in small nuances of this non-intricate problem.

How much pouring (filling volumes)

• Engines 1.2 and 1.4 L - 3.6 l
• Engine 1.8 l - 4.6 liters
• 2.0 l - 4.3 liters (only 507 tolerance)

Before starting work, make sure that you all bought and have at hand:

• New oil;
• Oil filter;
• Rags;
• Tazik on ~ 5 l;
• Key for removing protection and drain plug;

Work stages

1. Warming up cold Engine 3-4 minutes. Cold oil wakes badly to flow from the engine, as a result there can be a lot of dirty oil that in the end you mix new. Thus deteriorate the characteristics of the new oil.
2. Put the car on the jacks either on watching pit (perfect option) for convenient access to the bottom. In some models, the "protection" of the engine crankcase can be installed. It needs to be removed to access the drain plug.
3. We unscrew the plug of the fuzzy neck, take out the oil probe. Oil faster merges if there is a through hole.
4. We substitute a basin or any other dishes that can accommodate 5 liters of work.
   
5. Unscrewed drain plug The key (better if the ratchet wakes). It is best to immediately expect that the oil wakes up hot. At this stage of work, you need to be most attentive.
6. After a complete drain of old dirty oil that has a black color, we remove the basin aside.
7. Optional item is the washing of the engine special washing fluid. You will be surprised at which black oil will fall out with this liquid. Use this liquid is very simple. Pour into the engine, pre-tighten the drain plug of course. We start the car for 3-5 minutes. At the same time, we chase and warm our liquid on the old oil filter. After, wasting and merge into a free container.
8. We change the oil filter to a new one. Before put new filter, pour about 100 g of fresh oil into it and also lubricate the rubber sealing ring on it.
   
9. Pour new oil. Making sure that the drain plug is spinning, and the new oil cleaning filter is installed. We can start the fill of the new oil focusing on the pouch. The level should be between the minimum and maximum mark. Also, you need to remember that after the first start of the engine, some oil leaves and the level goes down.
   
10. Re-check the oil level on the PCU after the first start. Let the engine work for about 10 minutes at idle.

What oil pouring

• Oil type - synthetics
• Summer - 20W-40, 25W-50
• All-season - 10W-50, 15W-40
• Winter - 0W-40, 5W-50
• Recommended Brands - Shell, Mobile, Castrol, Lukoil, Xado, Valvoline, Zic, GT-Oil

Video materials

What oil to use to replace and when?

Oil for these motors use only with tolerances VW 504 00; 507 00., as well as viscosity 5W-30.. By regulations, oil replacement is made every 15,000 km or every 12 months . Under our operating conditions, we recommend replacing the oil every 8 000-10 000 km or every 12 months in .

Spare parts necessary to replace oil:

Original spare parts:

Analogs of spare parts:

* - Miscellaneous oil packing is indicated, both items should not be purchased.
The cost is approximate and indicated for 2017.

Replacement procedure on Skoda Yeti 1.2 TSI CBZB:

1. Under the hood we open the lid of the oil refining neck.

2. pull out the oil probe, not completely, in order to get air.

3. Weaken the oil filter, but do not remove, we give the remaining oil in the filter.

4. Remove the protection of the engine crankcase, unscrew the screws of the mounting of the hides, and then the fastening bolts of the protection itself.

6. Let us drain the oil. We drag up to the moment slow drop drops of oil.

7. Spinning new Drain plug and tighten with a point of 30 nm.

8. We are cluttered from the oil drain plug and the adjacent part of the pallet.

9. We install the Carter protection.

10. Remove the oil filter.
Pay attention to the bracket oil filterIt may remain a seal from the filter, as in our case, it must be removed.

11. Remove the oil filter seal.

12. Wipe from old oil planting place Oil filter.

13. Install a new oil filter and tighten the point of 20 nm.

15. Pour new engine oil into the engine.
Approximate volume of oil with a 3.6 liter oil filter replacement.

16. We wipe the planting place of the oil-tapping neck cover.

17. Close the oil refining neck. We climb the valve cover if the oil was shed.

18. We start the engine, give him to work 2-3 minutes, then wasting and give to stand 3 minutes in order to glass oil. We look at the oil level, if the oil level is slightly higher than the middle, then the oil does not fill, if not, it is necessary to add oil.
From the MIN mark to MAX mark, approximately 0.7-0.8 liters of oil.