How the generator belt is stretched on the Gazelle Business. How to solve problems with an expansion tank

Insufficient belt tension worsens blowing the cooling system radiator and leads to overheating of the engine and elevated belt wear.

With too strong belt tension can fail the fan drive bearings and tensioner roller.

With a properly adjusted tension, the belt should be fed at 8-10 mm with an application of 40 H (4.0 kgf) in the middle between the fan pulley and the tension roller.

The belt tension is adjusted by moving the tension roller.

Replacement and adjustment of the tension of the drive belts of the aggregates with the engine ZMZ-402

1. The head "on 13" weakened the nut of the upper mount of the stretch pulley bracket (cooling system hoses for clarity removed).

2. We will weaken the key "on 14" by the lower fastening of the tension pulley bracket, holding the bolt "at 12"

3. Sweep the stretch pulley bracket to the block and remove the belt from the pulleys

4. Having a belt between the fan impeller and the radiator, remove it

Weakening the upper and lower fastening of the generator

Sweep the generator to the cylinder block.

Remove the belt from the pulleys, to produce it through the impeller of the fan, similar to the removal of the fan drive belt.

We put on new belts on the pulley.

We stretch the fan drive belt, pushing the stretch pulley from the cylinder block, and tighten the top and lower fastening of the tension pulley.

The drive belt is tensioning similarly by moving the generator from the cylinder block, after which we tighten the upper and lower fastening of the generator.

We check the adjustment of belt tension, applying the force of 4 kgf to the middle branches.

The generator drive belt is 8-10 mm, and the fan drive is 7-9 mm.

If necessary, repeat the adjustment.

Replacement and adjustment of the tension of the belt of the actuator with the engine ZMZ-406

1. We relax the key of the tension roller fastening tightening tightening (for clarity, the engine radiator is removed).

2. Weaken the belt tension rotating the key "on 10", counterclockwise tensioner bolt

3. Remove the belt from the pulleys.

Install a new belt.

Rotating a tensioning roller bolt, we achieve a 15 mm belt deflection under load 8 kgf, attached in the middle of the horizontal drive branch (between the pulleys of the generator and the pump)

Tighten the tension roller fastening bolt.

Loosen the tightening of the bolt 1 for two or three turns.

Opening the adjusting bolt 2, weaken the belt tension and remove it.

Inspect the belt.

If there are cracks, bundle rubber, dummy, deposition of contaminants between ribs, etc., replace the belt.

Inspect the pulleys.

In the presence of pollution or pulley damage to clean or replace.

If you need to remove the tensioning device, unscrew the three bolts 3, while it is more convenient to turn the bolt under the roller, moving the roller up.

Installation

1. Wear a belt on the crankshaft pulley.

2. Wear a belt on the pulleys of the water pump and the generator.

3. After that, put the belt on the tensioning roller.

After installing the belt, adjust its tension.

Tension adjustment

With a properly adjusted tension, the belt should be fed up 15 mm when annexed an 8 kgf force is in the middle between the pulleys of the generator and the water pump.

The belt tension is adjusted by moving the tensioning roller.

1. Loosen the tightening of the bolt 1.

Watching or turning over bolt 2, adjust the belt tension. Tighten the bolt 1.

2. Check the belt deflection.

In detail in pictures:

The key "On 12" weakened the tightening of the tension roller mounting bolt (for clarity, the engine radiator is removed).

Weakening the belt tension rotating the key "on 10", counterclockwise tensioner bolt

Remove the belt from pulleys

Install a new belt.

Rotating the tensioning roller bolt, we achieve a 15-mm belt deflection under the load of 8 kgf, applied in the middle of the horizontal drive branch (between the pullees of the generator and the pump).

Tighten the tension roller fastening bolt.

Replacing the tension pulley and the tension of the drive belt of auxiliary aggregates

Weakening the tension of the drive belt.

Fully turning the tension pulley fastening bolt

Remove the pulley from the tensioner axis.

If necessary, the end key or head "on 12" turn the three tensioner attachment bolts

Remove the tensioner mount from the engine

Install the tensioner and pulley on the engine in the reverse order, after which we stretch the belt.

Car generator belt Gazelle Business is responsible for the transfer of engine rotation to the auxiliary to its units. Some devices are capable of moving several mechanisms at once.

The drive belt can affect the pump, the hydraulic power steering pump, various compressors and even the generator. In order for all the above mechanisms to work simply and smoothly, it is necessary to replace the parts in a timely manner, and if necessary, adjust its tension. In today's article we will look at: where the belt is the belt of the Gazelle Business generator, signs of its wear, dimensions, diagram and step-by-step installation instructions. Well, what to proceed.

Location of the belt Generator Gazelle Business

The generator belt on the Gazelle business is located under the hood in the front of the car! As shown in the screenshot

It's easy enough to find it, so at this moment I will not sharpen my attention and your attention.

Gazelle Business - Signs of Generator Belt Wear

In order to find out how much the generator belt on Gazelle business is enough to have its visual inspection. If you notice:

1. Oversight
2. Surface detachment
3. Mechanical damage, etc.

Then do not postpone the replacement drive belt In a long box, and immediately replace this consumor.

Belt Size Generator Gazelle Business

Gazelle Business, as well as any other domestic production car has a lot of inconvenience, for example, the generator belt is set from the manufacturer's plant under the labeling: 8pk 2155 or 8pk 2166 has a small size, so when replacing it, it is almost impossible to put it in place!

Video Replacing the Generator Belt on Gazelle

Installing a belt of the generator on the Gazelle Business Step-by-step instruction

In order to replace the generator belt on the Gazelle Business to need to perform the following step by step instructions:

1. Ratchet grind the drive belt through the pulley of the generator
   
2. We use the belt on the pump pulley from the engine and rotate the ratchet pulley of the generator clockwise:
   
3. Intercepting after a small belt gathering, we continue to gradually rotate the pulley of the generator:
   
4. We seek and throw off the old belt of the generator
   
5. Take the belt in all the rollers, wear all the streams on the pulleys! We only leave the pump pulley not dressed. The tensioner does not touch at all, and the meaning, the move is small and does not allow you to freely wear a belt.
   
6. We take everything out the score and feed her belt on the pulley pump in the tension! And gradually rotate the ratchet clockwise! It is important that the lower edge of the belt rearranged through the Pump Pump Center:
   
7. The main thing is to keep scolding and not to let her go until the belt wrap the pulley!
   
8. You can not remove the radiator and remove and remove the belt normally. The only thing that is exactly the replacement of the belt, it is more difficult to block it through the impeller and everything.

Another important moment to which I would like to draw your attention - tension belt generator ! In order to accomplish this job we will need:

How to weaken the generator belt on the Gazelle Business

In order to weaken the generator belt on the car Gazelle business, follow the procedure that I described above in the part of the tension of the drive belt. One difference, weakened, and not stretch the screw belt tensioner

Replacing the belt Generator Gazelle Business DIY - Video

Loosen the tightening of the bolt 1 for two or three turns.

Opening the adjusting bolt 2, weaken the belt tension and remove it.

Inspect the belt.

If there are cracks, bundle rubber, dummy, deposition of contaminants between ribs, etc., replace the belt.

Inspect the pulleys.

In the presence of pollution or pulley damage to clean or replace.

If you need to remove the tensioning device, unscrew the three bolts 3, while it is more convenient to turn the bolt under the roller, moving the roller up.

Installation

1. Wear a belt on the crankshaft pulley.

2. Wear a belt on the pulleys of the water pump and the generator.

3. After that, put the belt on the tensioning roller.

After installing the belt, adjust its tension.

Tension adjustment

With a properly adjusted tension, the belt should be fed up 15 mm when annexed an 8 kgf force is in the middle between the pulleys of the generator and the water pump.

The belt tension is adjusted by moving the tensioning roller.

1. Loosen the tightening of the bolt 1.

Watching or turning over bolt 2, adjust the belt tension. Tighten the bolt 1.

2. Check the belt deflection.

In detail in pictures:

The key "On 12" weakened the tightening of the tension roller mounting bolt (for clarity, the engine radiator is removed).

Weakening the belt tension rotating the key "on 10", counterclockwise tensioner bolt

Remove the belt from pulleys

Install a new belt.

Rotating the tensioning roller bolt, we achieve a 15-mm belt deflection under the load of 8 kgf, applied in the middle of the horizontal drive branch (between the pullees of the generator and the pump).

Tighten the tension roller fastening bolt.

Replacing the tension pulley and the tension of the drive belt of auxiliary aggregates

Weakening the tension of the drive belt.

Fully turning the tension pulley fastening bolt

Remove the pulley from the tensioner axis.

If necessary, the end key or head "on 12" turn the three tensioner attachment bolts

Remove the tensioner mount from the engine

Install the tensioner and pulley on the engine in the reverse order, after which we stretch the belt.

Replace the generator belt on the Gazelle.

The generator belt rupture is often a challenge problem. If this happens on your Gazelle It is measured, since you pay attention to this question not earlier try replacing the belt to learn that it actually causes stones.

If you do not need to change the belt after 150-200 thousand miles or when planned maintenance, the situation when it fails is abnormal. how to tighten the generator belt to generator belt Hyundai like work. If this often happens on your gazelle (not every 50,000 km), pay attention to this problem before trying to replace it to find out what actually causes frequent breakdowns. BUSINESS GAZELLE EURO-3 MANAGERNIENCE RELATE RECORDER NORMARY OR BET is not stretched after installation.

Meanwhile, the belt Gazelle was still broken. Be sure to start with the purchase of a new one. Some motorists prefer to take packets with cheap, non-original spare parts, stating that "In any case, they are constantly torn, let me always have a stock in the car." Detailed information on how to correctly replace the generator belt on the 16-valve VAZ-2112 engine. You have a very quick belt belt always for two reasons. Only one of them is constructive (for example, shift offset, as it is called lubricant). Next reason - just their bad quality. (Wedge belt) on 4216 Gazelle Business Generator GAZ 3302 Gazelle-Business. Greedy, as you know, pays twice. To check the tension of the generator drive belt, press the line to the belt in the middle between the pulleys of the generator and the coolant pump. This is not quite expensive, as spare parts themselves are cheap, so we recommend buying belts, nettle in the online store. In other words, gas spare parts from the official SPEI spare parts supplier. I bought so strap definitely suitable for your modification only for your pulleys, and not in the center.

You may Also Like

Replacement of tension roller on Gazelle 4216 business

replacement generator belt, Fan support rollers gas 3302 Gazelle—business two. As on 8, that's all the alternator belts on a tweln 1.5 2112 Replacing the steering power engine at EUR VAZ 2112 Z. on the Cummins website ISF 2.8.

replacement generator belt, support roller and fan gas 3302 Gazelle-Business DV. The Gazelle Business EURO-3 belt requires the Gazelle Business EURO-3 belt size under a wide pulley. Cummins ISF 2.8.

masters have not translated yet, throwing puzzles as they call these non-standard solutions.
What you need is a bought belt, we turn to the operation of its installation. I did everything in Louisiana. And yesterday broke the belt Generator Gazelle Business. How further. how to remove the bottom grid for gazelle Renault Logan. Tuning how to remove the grid. Please note that it is better to work with gloves, because there are many sharp turns in the area of \u200b\u200binterest to us if we make changes directly to the track, then some units under the hood, of course, have no time to cool
It is better to immediately disassemble the front panel - this is not a radiator cover. The space under the hood is not much better to facilitate working conditions. Using 12 keys, unscrew the pair of bolts on both sides of the panel, using 10 keys, one bolt is specifically under the hood lock. The decorative lattice is screwed up with another 2 bolts from below. We do not place the grille next to the panel (as far as the cable lock allows).
Now, using a 12-digit key, loosen the belt tensioner screw on the generator armed with the corresponding handle, translate the generator to the engine. So we have weakened belt (If he did not break before) Replacing the generator belt on the VAZ 2110, VAZ 2111, VAZ 2112 when the belt is fastened. Now you need to loosen the nut pulley tensioner; not nut pulley tensioner; Do not move the pulley towards the engine; Do not remove the belt.

You may Also Like

If with a belt generator We do not change the rest, then remove the belt of the fan from the pulley on the crankshaft, carefully twist it between the fan blades. Later we also dismantle the water pump belt. How to change your belt gazelle | Then just install new, do not pull them. After all, we return to the place, the front panel is not a grille of the radiator - the changes are made, naturally go on the road.