The secrets on the wheels do it yourself drawings. How to make a secret for a car from handles with your own hands? On the hood of cars

One of the most popular goods on it. Because of this popularity of stolen used wheels, a whole course has appeared - thieves that specialize exclusively on the stealing of the wheels. To combat such an unpleasant phenomenon, companies appeared that tried to solve this problem by creating special protective mechanisms that could prevent theft of automotive wheels. The most popular today are the so-called "secrets".

Many car owners after the loss of the key from the secret fell into a dead end, breaking their heads over how without a key. However, despite all the difficulty, there is still a way out of this situation. It is about this today and will be discussed in my next article, I will try to help those who caught my own fishing rod.

For this, truth you will have to be for some time to become a night throat, which removes the wheels from cars. The difference will be only that you, in contrast to the thief, you do not need to be afraid of the host of the alarm, and it will be possible to operate when light. Of course, the task is not the easiest, however, fully fulfilled, all that is required of you is accuracy, patience, time and good physical training.

If your secret is inexpensive, and the problem consists only of how to unscrew without special key - The process will most likely not require any special skills and will end pretty quickly. But if the secret has been installed for a long time, and you do not remember yourself when the last time it was unscrewed - most likely, it will have to be tinted, since it could be bought from long-term operation.

First method It is to break the secret by tightening and release the rest of the bolts. To do this, it is necessary to stronger tighten the remaining nuts on the wheel, thereby removing the excess load from the secret. Then raise a little a wheel with a jack, then catching up in a secret from all sides and lower the wheel.

Next, you need to completely unscrew the bolts so that only the accurate secret remains tightened, after which it is a little subdominating the wheel. After that, try to gently shake it on the hub, having previously going through the entire area of \u200b\u200bthe secret (WD-40).

Last step. After all the braced again, turn off all bolts and nuts as hard as possible - this will allow you to remove the load on the secret itself. Tightening should be symmetrically, gradually every one, it will eliminate the possibility of sowing the disk. The tighten must be maximum! If everything is done according to the instructions, the secret must unscrew without much effort.

Second way. If you have only lost the key from the secret, but the secret itself is unscrewed normally, then you can try to unscrew it with another method. It consists in the selection of a suitable head to the diameter, which, with the help of a sledgehammer, it is necessary to gently fill on the secret. After that, try to break it with a gorot. In most cases, it is possible to unscrew the secret.

If you have nothing happened, I recommend contacting the service, there are most likely to help you, but it will be worth a lot of money, and besides, it is not a fact that it will be possible to save the disk. Be that as it may, you shouldn't panic, try and you will definitely work out.

Video how to unscrew the "secret" without a key

It is hardly worth questioning the benefits of the so-called, the secrets, honestly perform their role on protecting the wheels of your car from attempts to theft. Unfortunately, it is often quite common to situations when due to the loss of a special key with a configuration secret, the owners of vehicles are forced to go to mechanical damage wheel Discor contact the costly service of car service.

Meanwhile, there is quite simple demonstration methodwhich, what kind of sin is sometimes enjoyed by attackers. However, it is not enough useful experience to adopt, especially since in case of this problem, you will not have to wait for darkness and work, fearing not only alarm system, but also raised passers-by.

Removing the secretion by the method of having adjacent bolts

Immediately make a reservation, that despite the seeming simplicity, this method will require you to considerable time and time and considerable physical effortsBut as a result, you will have a costly alloy wheels intact Lomaster from a miracle service.

1. Getting Started to work, first of all, it is required to twist all standard bolts and nuts on the wheel, excluding the secret itself. Thus, the load from the secret will be removed.
2. Next, it is necessary to raise the wheel by jack and unlocking blows from all sides to catch a secret. This can be done by shaking the wheel in different directions. After performing this preliminary procedure, the wheel is lowered.
3. At the next stage, all available bolts and nuts are twisted - while the wheel remains fixed by one secret.
4. Raising the wheel on the jack, we perform with easy efforts to perform several loosening movements on the hub (to increase the effect, it is pre-seen a secret to the WD-40 tool or similar to the drug).
5. After that, standard bolts and nuts are installed in place, and they are again tightened with maximum effort. An important condition - the tightening should be performed symmetrically to avoid the disk skew.
6. As a rule, after the specified procedure, the secret is so weakened that it can be easily unscrewed by hand.
7. If the secret is very accurate, and it did not work out the first time - nothing is terrible, not in a hurry, repeat the procedure and the required result will not make yourself wait.

Removing the secrets extractor for nuts

In order to remove a secret with the wheel with an extractor, you need a set of this tool, hammer and balloon key

Extractor- Redented end head with high strength. The inner part has a characteristic vintage cut on the left side (opposite to standard thread)

How used?

The extractor is clogged with a hammer right on top of the secret nut, then twisted with a standard balloon key

Removing Gator Grip or Gross

Unfortunately [or schucha], it is impossible to remove all the secrets of the universal gator grip or gross nozzles. Only a secret fastener with an outdoor pattern, such as in the photo below.

Such or similar secchats are easily removed by a unifail GROSS or Gator Grip nozzle

Remove the McGard and Farad secrets using Gator Grip

Remove sequente Farad.and McGard This nozzle does not work, because Pins nozzles do not fit inside the secret drawing

Take in hand welding

In addition to the method, about which we told, there is always the opportunity to call in the car service and, welding steel bolts to the wheeled nuts, carefully unscrew the spoiled secret. Do not forget to protect the cast aluminum disk during welding. It must be closed with refractory cloth.

How to take a secret. Video

Key recovery on secret code

If you, by a happy chance, did not throw off the packaging from the secret, then you are very lucky. You can order a duplicate key official dealer McGard, for example, this or that. The cost of such a service from 1500 rubles

Car hijacking for Russia, unfortunately, is a frequent phenomenon. However, even the presence of the most modern and reliable means against the hijacking, not capable of 100% to protect the car from the hacker by the decision, is undoubtedly the installation of the secret, which makes it much more complicating your hijacking vehicle. This mechanism and methods for its installation are described in detail in this article.

Secretakes on the car and its types

The secret is an auxiliary mechanism or button. This device is installed in the selected location and blocks, when you try to hijack, start the engine units or gearbox. Not always in the role of the secret is the button or toggle switch, it can be bolts and nuts installed on wheels or numbers. However, this remedy will allow the car with the greatest probability to be untouched. The secret can also block the hood lock and the operation of the fuel pump, in order to avoid draining fuel and theft of spare parts. If you compare the alarm and the secret, then the second option is the most profitable primarily due to the size and cost.

Modern secret devices are installed in various places, for example, on the hood, engine, wheels, license plates. You can make a secret and do it yourself.

On the wheels of the car.

This device on the wheels was distributed in scarce times. Prevented from encroachment to vehicles. We are separated by profile - with a figured profile, an asymmetrical polygon or holey. The bolt with a non-standard shape of the head significantly complicates the dismantling with priests. Metched in the form of a polygon, differ in the number of faces, and the multifaceted such a secret, the more expensive it is.

If you choose cheap secret mechanisms, then experienced attackers will not make much difficulty to dismantle the wheels from your vehicle. All because the number of combinations of keys is very little. At the same time because of poor-quality material Slots can be spoiled. The wheels, of course, will remain in place, but it will now be a problem for the owner now.

It is necessary to choose a secret famous brand For several criteria:

1. Quality of manufacturing material. The metal of the product must be as hard as possible to avoid the core drilling to a regular key or other fixture. Check metal hardness can be used in the usual file.
2. Surface. It is better to choose the product with a galvanized surface to avoid bipigation. Chrome secrets look better, but it is not insured.

The best secret devices on the wheel wheels produce brands such as McGard and Farad.

On the hood car

This type of mechanism is designed to protect the parts of the car under the hood. The main task is to block the intruder penetration under the hood of your car. The most common secret is installed on this part of the car, is to install another cable for its discovery. The cable that opens the hood from the inside is equipped with a lock that prevents penetration into motor compartment. You can still install an electromechanical lock, which will also be prevented by hacking the hood. The same systems can be installed in the car trunk to protect its contents.

On the car engine

Significantly complicates the hijacking of the car, because a considerable time will need to remove the protection of the hijacker. According to the principle of action, it resembles an immobilizer, but no key and items that need to always have with you, it is enough just to turn on the toggle switch where you put it.

The principle of action of the secret is pretty simple. Installation of an additional chain, which bursts power, for example, with ignition. Without this system, naturally, the start of the engine will be impossible. The location where the button or toggle switch is located individually stipulated with the car owner. Such secrets may be of varying degrees of difficulty - from the simple button to the object being moved to the desired place. Most models have a "service" mode, which allows you not to issue a place toggle when performing maintenance. The most difficulty secret in the engine is an injector type for motor-type motors due to the presence of a large number of chains, when the launch is unable to run.

The advantages of this type of mechanisms are a relatively small cost (about $ 50), secrecy, the presence of an autonomous mode of operation (when removing the battery), ease of operation. The secret will be even more efficient if it is professionally installed. The most reliable devices were products of Meguna, Escont, Validator.

On license plates.

For quite a long time, the resale of twisted license plates is flourished by the legal owner. The attacker, as a rule, says that he found them and asks for a fee for his services, and the owner simply does not want to mess around with new numbers, spending nerves, time and money. Therefore, car owners redeem their license plates at thieves.

But license plates can remove and follow the alarm of the car. How to protect the car from the twist of this important part? There are no paid parking lots everywhere, so it is necessary to deterre in any conditions. The secrets on license plates make it possible to reduce the probability of 90%. How do they act?

The numbers put special bolts with an unusual hat, to which it is difficult to pick up the key. Protection of license plates also happens in the form of a special frame from a stainless steel covering the entire number. To the frame of the canvas, the number is screwed by bolts that have a cap spilt. If the thief hurts to assign this part of the car, it will be very difficult to stop it, but if you put a lock nut and not tighten it tight, the scrolling of the bolts will deliver certain problems.

Making a secret with your own hands

If you combine fantasy, technical mind and various types of auto protection, you can make a unique tool that is not under the hijacker. And you can use the ready-made tips of the masters, if your method is not inventy.

• install in various places of the salon Sacks in the rupture of the chains, which were held to the ends of the starter or carburetor;
• overlapping valve exhaust pipe using remote control;
• installation of a magnetic latch for locking the steering wheel and gearbox;
• immobilizer is installed on electrocups leading to the starter;
• fastening the radio transmitter causing a circuit leading to the starter or carburetor.

The simplest options include blocking the steering wheel using a special-to-kocher device closing on the lock, you can make it and with your own hands at home in the presence of appropriate skills.

Types of secrets made by their own hands are divided into active and passive. For example, for passive devices, it is necessary to submit voltage, only after that the engine starts. At the same time, the attacker loses precious time and leaves the car.

It is possible to build a mechanical protection tool, for example, on wheels using old bolts from the classics, but it will require short-sighted skills and skill.

However, many owners stop in the mechanical method, motivating this by the fact that the mechanic fails less frequently than the electrical chain. Each car host, when creating such a device, should have a set of tools, knowledge of electricians and mechanics, the skill competently carry out the installation of the device.

There are many nuances when choosing a way to protect the car from the hijacking. It is not necessary to put a cheap secret on the wheels - it is fraught with a breakdown or deformation of bolts and further difficulties in the installation of the wheels themselves. It should be remembered that the installation process with your own hands without certain knowledge is impossible or associated with many problems. Well combines the secret in interaction with the security alarm. Even the usual, screaming "anti-rode" will scare the thief. Individual alarm will deliver a lot of works as a hacker. Installing the secret occurs quickly and easily, if produced by professionals. A relatively cheap and simple device is capable of 90% reduce the likelihood of hijacking or damage to the vehicle. It is also necessary to take into account the risks in the manufacture of homemade electrical secrets, because the illiterate installation threatens not only your car, but also the property of other people in the event of a closure.

It is best to put such means of protection on specialized stations to eliminate all possible breakdowns with incorrect assembly and installation. But it is worth remembering that some car services can be in collusion with hijackers, which allows them to easily bypass all systems of protecting your car. In order to avoid this, you can consider the option with the installation of the secret in the neighboring region. It is also necessary to insure your car, because the installation even the most perfect secret does not give guarantees the safety of your car.

Below is a video about installing a secret button on your car

Anti-theft secrets are electric that do not give the engine, and mechanical that do not allow you to unscrew and steal the wheel. As the simplest secret, a regular toggle switch, located in some secret place, can act as the easiest secret. He can smear the power supply chain fuel pump, ignition relay chain or starter. Special nuts or wheel bolts are simple. But very reliable protection from their theft.

Unique electronic secret - the most effective protective equipmentwarning car hijacking. Even if some thief pulls your keys with a key chain, he does not start the car, as it will not know which a touch button is located blocking the start of the motor. It is important to make that car alarm use other blocking methods.

Secret as an alarm addition

The secret is an important and necessary addition to any alarm. Today you can easily buy scanners that turn out to 95% of existing signaling systems. For this reason, it began to steal things from cars often, because the thieves can now easily turn off the alarm. For this reason, there should be no valuable things in the car, since sometimes instead of the scanner, robbers use simple bricks. Theft is performed in a matter of seconds, and you can hardly catch up the thief.

Types of electronic secrets

Nowadays, there are secrets working on different management algorithms or having different security and service functions:

• sequential press of the button;
• secretakes with the control of the hood lock;
• secrets with limited code input code;
• serial entry of a specific code using standard or additional buttons;
• secretakes with motion sensors;
• secretakes with sirens connect.

Advantages and Additional Features

The most important benefits of using anti-theft systems include the following:

1. Electronic secrets are not read by means of software devices that have long started using hijackers.
2. By installing under the hood, the secret and supplying the auto mechanical protection, you will not allow an attacker to output or detect it.
3. Create a deactivator from the motorist, as a key chain from alarm, no one can.

Additional functions

Modern models of electronic secrets have a number of possible additional features:

1. Motion Sensor. This feature allows you to start the machine, but you will not be able to move on it. The option is great for use in winter when driving a car.
2. Anti-Hi-Jack function - modern addition anti-theft system. It works at the expense of automatic locking of the motor in the case when the owner opened the door without performing special actions that only he knows about.

You can break the starter or carburetor chain by connecting the toggle switch to the minus wire installed in some secret place. Load the wires applying to the usual keys in the cabin (headlight corrector, the heater is turned on). Thus, by connecting several similar togglers, you can win a little time.

Another options of the self-made secret is to overlap the exhaust pipe valve, which is controlled remotely. When you start the motor after some time it will stall. The exhaust gases will not go anywhere, so the car will create the impression from the hijacker that it is faulty, so the attacker will try to leave the crime scene as soon as possible.

Try installing an additional lock that blocks the gearbox or steering wheel. Special magnetic latches are especially convenient and effective in this case.

In each store of radio components, you can find a radio transmitter, whose principle is that the chain will close when approaching it. It should be connected to the wires leading to the starter or carburetor, as well as thoroughly hide them. Chief flaw The system is that you will need to wear a transmitter with you.

You can find various immobilizers in the form of factory secrets. Recently, there is a fact that such fixtures are increasingly installed on all modern cars. If you have nothing like that, you can install such a device yourself by connecting it to one of the electrical circuits of the machine, which is responsible for the normal operation of the motor.

If you have experience in installing such devices, try the system in action that allows you to extend the unlock time of the device with a hijacker. To do this, you need to make a system with a complex algorithm of influence on the armores and several blocking chains that activate the relay. If you do not have sufficient experience, trust the installation of the secret to a professional in the workshop.

Installation or creation of a secret for cars with your own hands will allow you to improve the safety of your car for a little money.