Radio-controlled car with your own hands. Detailed instructions How to assemble a machine on the control panel: Many build options, valuable tips and recommendations, practical guide

Each child wants to have a car on radio control. To date, such cars are quite expensive, and their children break them quickly, but do not panic in vain.

Skillful hands, fantasy and fodder materials will allow themselves to make such a car from cardboard that will not give way to power and passability by purchased plastic machines.
For its manufacture we will need:
· Cardboard from boxes,
· Construction knife,
· Pencil, line,
· Glue,
· DC motors,
· Wires,
· Turn on and off button,
· Soldering iron,
· Joystick management,
· Battery,
· Plastic circle, plastic tubes,
· Gum,
· Metal stick,
· Plastic cover for books,
· Plastic covers from plastic bottles of 6 pieces,
· Wooden sticks,
· LEDs and capacitors.

First stage
To begin with, we take a sheet of cardboard 9/28 cm. And cut out in it a few parts.
On the left side at the top, retreat approximately 1.5 cm. From the side edge and cut a 3 / 4.5 cm rectangle, do the same from the bottom, and on the right side, we retreat approximately 4.5 cm. And cut the rectangle 2/4, 5 cm. Identical cut down from below. Menu by these rectangles in the middle cut out the strip 1 / 4.5 cm. This item will serve as the bottom of our car.


Cut down the side.
For this, on cardboard 9/28 cm. It is necessary to draw the type of machine. In the left side, retreat approximately 0.5 cm. From the side edge and 1 cm. From the bottom, feed a line of 4 cm long, but from her line tilting in the middle of 5 cm long. Right until the end of the cardboard. On the right side, swipe from the edge just below the middle of the horizontal line from the edge in the middle, a little up a little up, a length of 7.5 cm, and from her line 5.5 cm., Taking up and tilting in the middle. Inside this piece of cardboard, you can draw windows, doors and wheels. And the wheels and windows also need to be cut, and the doors simply cut to open and closed. There are two such parts, because they will be the side of our car.


Wheels
To make the wheels take 4 covers from plastic bottles and make in the middle of the hole. At the bamboo stick for the barbecue, glue the small plastic circle in the middle, by making it first in it suitable for this hole. Now take a plastic tube like a cotton wand, measure the size on the cardboard that will be the bottom of the machine. On the right side of the lower cut rectangle to the middle strip, cut two of these segments. Then put them on the bamboo stick close to the glued circle on both sides. After putting the caps from the bottle and, retreating from the strips of about 0.5 cm., Stick them, and cut the residue of the bamboo stick so that it does not look out from under the covers.


In the middle, where the plastic circle is glued, put on the gum. Now glue the wheels to the place intended for them on the right side of the cardboard, the gum must be in the middle hole. To the next two lids, you need to insert plastic tubes into the hole, glue them, and then cut off the plastic tube at the height of the lid itself. From the body of the ballpoint handle, we cut a two piece of 2.5 cm. We put them on a metal wand and with the help of pliers we strip this stick. As a result, it should be: a horizontal metal pin with a length of about 3 cm, at an angle of 90 degrees.
Source: zen.yandex.ru.

Crawler Tank on Radio Control DIY

A little disturbing from radio-controlled flying toys and go down to the ground. Today I will tell you how to make a platform for caterpillar technique for a penny for a penny. You can put a tank, excavator, bulldozer, or everything that comes to your mind.
Self-timers on radio control - a very entertaining hobby.

Materials

We will need a 2-channel transmitter, a control panel (joystick), two 9g servo servo, the old cycling chamber, plastic sheet and 8 sticks from ice cream. And yes, do not forget about the Li-Pol 3.7 battery at 150 mAh.
Glue, pieces, knife and scissors take on the shelf.

Preparing motors

Servo drives will be used as engines. It is necessary to disassemble from and cut limiters on gears. Standard wires cut and solder 2 to see each motor (+ and - respectively).

From plastics, we cut the plate 40 to 100 mm and two plates of 20 per 100 mm. In small plates we mount servos. And with the help of glue, we collect the framework.

Rollers are also made from plastics: painstakingly and gently cut out 12 circles with a diameter of 20 mm and 8 circles of 30 mm. We glue 3 small mug, and at the edges of 2 large. So we get 4 rink. Krepim to the frame on the bolts, drill holes in rinks and in the frame.

Caterpiles

From the old bike chamber, we cut two strips with a length of 25mm and 6 mm width. Bear every strip.
Yes, the glue will endure, the load on the joint will not be big.
Strips from ice cream mode on 14 mm strips and glue longitudinally to the made caterpillar.

All the most wise stages are completed. We put the caterpillar on the rollers. We solder the wires from servo drives to the transmitter and connect the battery.


Profit. Homemade is ready.
Patency turned out to be amazing. Further case for your fantasy to give the basis of a certain appearance!


Thank you for your attention and huge thanks to the author of the self-made Creative Chanel..
Source: zen.yandex.ru.

MiG 29 from EPP foam on radio control

Greetings to all lovers large-scale models and models on RC (that is on the control panel). In October 2017, a colleague at work I bought myself a radio-controlled fighter MiG-29. This fighter my colleague made himself from the EPP of the foam (foam that bends) and carbon ridges that hold the form. In addition to the plane, he gave me a gift as a gift with rocking chairs as well as the battery at 500 mAh. I bought it because I am a novice aircraftist and how any novice aircraftist is afraid to break his first aircraft.
I chose this aircraft because of its material, as it is made of EPP foam. And the EPP foam does not break down, thereby begging to reducing the chance of painting my model. Since I had already had a control panel and receiver, I didn't have to buy all this.
(photos were made on the phone therefore the quality of the pictures will not be the best)


On this fighters, however, the model on RC is working:
- High heights,
- Rules directions
- elephant,
- engine
I did not show everything below.




And here is the servors themselves, so they are fixed on the wing, they lead to the movement of Aeron:


Naturally, the plane leads in motion so this is an electric motor in type 2205. On my model, the motor is standing on the nose, although on such models it stands in the middle of the plane. That's what it looks like:


On the way to the motor stands the regulator, it is responsible for the number of revolutions on the motor and therefore for the speed of the model itself. That's how it looks:


All this is powered by batteries, on this aircraft there is a Li-Po battery at 450mAh. Here it is:


It is attached on velcro (like on shoes). Here is what the battery mount looks like on the case of the model:


Since the model is made from the EPP foam, when it will not be able to keep the form (since the EPP flexible foam) and that he kept the shape and did not get into the carboxyl rails and the needles. Here they are black:

Well, about the plane, everything seemed to tell everything and showed, oh yeah did not tell about the screws, well, the screws should still be picked up, although the couple in stock is lying. In addition to the aircraft itself, I still got spare parts for it. Here they are all:


Below I will show them in more detail, by the way, some of them are not yet on the plane I have to still connect and configure them.
1) Screws, you ask why 2 screws, but because this item that is often broken when the aircraft falls and the falls are all. Therefore, they are even sold most often with a set of several pieces.


2) Li-Po batteries. I already talked about the battery, but I also have 2 of them, mostly they always take 2 pieces, as one quickly discharged. One battery is enough for 10-20 minutes of flight. One on my 450 Mah and the second to 500 mAh.


3) servo cereals with rocking chairs. As I already told the servo, the moving parts of the aircraft namely:
Aileron
High heights
Rules directions


4) receiver with a plug. I'll tell you about the plug when I tell about the control panel and tell about the receiver. The receiver's task to catch the signal from the radio control panel and transmit it to all devices. All devices are connected to it Namely: the speed regulator with a motor and all servo. That's how it looks:


Well, about the plane told later I will tell about the control panel, I dedicated a whole post. (If I missed something, I will definitely add). Well, what would learn about the control panel subscribe to me. And you will definitely learn!

And I decided to repeat. With the beginning I ordered the equipment, servo drives, ammortizers that are less on before and big back. The photo is not so



i found the engine from chainsaws in 45 SS and 3 horsepower.
And I started making a frame. The first damn turned out to be a comment because I did it from the metallic profile and the frame turned out to be heavy and the roast that I did not fit.
Here I decided to try to do something easier and stronger. The first hand I got a leaf of aluminum from it, then I decided to make a frame. The first light and durable (in some kind of degree) one of his minus is that it bends, but it does not matter. In order for he, I would not be strengthened it in the center. By installing 2 strips from an aluminum profile. I turned out to be surprisingly durable 32 kg. Gircus stands as a health, and this is necessary for me. The frame turned out 73 cm, the width 25cm thickness is 2.5mm. Here is the actual frame.

Then I thought how to make a running how to install the front wheels from the beginning I wanted to use an aluminum-shaped profile to set the suspension on it but not where it could not find it (I did not think that this is such a deficiency d). It would buy aluminum corner 25 mm but then I learned that Rophile could buy in the Castor, but it was too late, that's what happened

the height of the corner turned out to be 6 cm. I still think how to do it better because the model will be rear-wheel drive and such a scheme is no longer suitable and do without the main parts rear suspension I don't risk a risk because I need to make a prediction. And while I am waiting for the main parcel without which this machine is not when it does not move from the place. It includes a set of drive axes.

the receiver is like native in my stupidity burned

and wheel adapters

To the completion of the first part, I want to show something about how my model will look like I'll tell you immediately, I didn't find them on the Internet. To be continued.

Becoming the happy owner of a powerful and reliable toy controlled at a distance - the dream is not only many children, but also some parents. Today manufacturers are ready to offer a variety of entertainment that can surprise even the most sophisticated young consumers. Technique on radio control can become an excellent gift, and when it is properly operation, it is capable of listening for quite a long time.

Among the large number of models, gasoline cars on radio control deserve separate attention, since the power and reliability indicators are among the highest. About the peculiarities of these popular toys, their specifications And the views then will be discussed.

What is a gasoline machine on remote control?

First of all it is worth saying that such a product is almost complete, but only a reduced copy of the usual vehicle. These machines also go on gasoline, while the maximum speed values \u200b\u200bare really impressive: some models easily accelerate to 80 km / h. However, it will not be noted that such mechanisms periodically require repair, as well as ordinary cars, therefore, to the process of driving, it should be approached with all seriousness.

Of course, it is not recommended to use such toys in the room, since it is possible to estimate all their potential only on open areas, for example, on asphalt tracks.

The main characteristics of gasoline machines on radio control

The varieties of these models there are many: it is cars for highway races, and buggy, and samples intended solely for drift, which will be discussed a little later. This or that typewriter on radio control with a gasoline engine has its own characteristics.

So, a distinctive feature These models are a remote. In samples on the radio control, its maximum interaction radius is usually about 150 m.

Another unique item is gas enginewhose power can be different. From what type of motor is installed in a particular model, the scope of its operation depends.

If we compare gasoline machines on radio control in size, it can be safely distinguished both children's reduced products and large toys that will be more suitable for adult lovers of such equipment.

What should the choice of gasoline radio-controlled machine depend on?

In order for the acquired technique to deliver only joy, it is necessary to pre-carefully examine the entire range of products and stay at the most suitable. Selecting the machine for the child, it is necessary to be guided first of all its age, but it is also worth thinking about how it will use the toy. If the main requirement for the product is the speed, then it is best to choose a high-speed sample, and an off-road model is ideal for overcoming obstacles.

Than younger childThe easier it should be control. It is better to abandon the acquisition of highly sensitive devices so that the master of the typewriter has experienced problems. At the same time, attention should be paid to the size of the product, since some gasoline cars on radio control are quite voluminous, which can be quite uncomfortable for a small child. Large models are the perfect option for adults.

Proper operation of gasoline machine on remote control

In order for such a toy to serve as long as possible, it is required to accommodately approach its content. Do not forget that the child can cope with such technique is very problematic, so it is better if an adult is always near. Of course, all repair and preventive work (replacement of fuel, oil, lubrication of parts, etc.) should also be carried out by parents not only because of the risk of equipment breakdown, but also because the fuel harmful couples are dangerous for the children's body.

Many gasoline cars on radio control are sold unchanged, so in the process of assembling such products it is extremely important to be guided by the attached instructions. In addition, security rules exclude any games near the sources of fire and open reservoirs.

Characteristics and advantages of radio controlled drift machines

As mentioned earlier, the technique on the fuel operating from the remote control may differ depending on its purpose. So, consumers are widely popular with gasoline machines for drift on radio control. These models like both adults and children, and their difference from ordinary high-speed toys is the following technical characteristics:

• such gasoline cars are equipped with special shock absorbers with drift springs;
• the tires of these products do not have a tread pattern and are more rigid compared to conventional models;
• as a rule, the basis of the body of such a toy is shockproof plastic, as well as a durable bumper, protecting equipment from shocks;
• the special design of the suspension allows you to perform various technical elements.

How not to make a mistake with the choice of gasoline machine for drift?

Toy cars on radio control, designed for such purposes, do not buy at all little childSince the minimum age of the owner must be 3 years.

In addition, it should be remembered that there are no fully universal models. This means that by purchasing a toy typewriter for drift, you should not wait for any other properties from it like high speeds or high patency.

Another important point is the type of embedded engine. Used to drift a gasoline machine on a radio control (a photo of various samples can always be found in specialized prints) should have a very powerful motor so that the load rendered to the model did not harm it. Equipment of a new product, as a rule, implies the readiness of the toy to go without the need to purchase additional details.

The main details of the gasoline machine on remote control

Not always the parents have the opportunity to buy your child an expensive toy in the store. But if we talk about gasoline cars, then such products can be made and independently. The device of these toys is largely reminded by the structure standard carSo for many drivers the installation process will be understood.

To deal with how to make a gasoline machine on a radio control, initially need to decide which details for this work will be needed. So, the set of standard toys includes the following structural parts:

• shockproof body;
• gasoline engine of the desired power;
• strong wheels;
• chassis;
• a set of tools in the form of different screwdrivers.

Features assembly

Gasoline cars on radio control do it yourself easy to make. After purchase essential materials Mounting should be done.

Attaching the front wheels to the frame, you need to make sure that they are easily rotated. Tires are best choosing rubber, since it is this material that has the highest possible adhesion with the roadpapers.

The body for the machine can be simply purchased in the store, but many owners want to create a unique toy and come up with their own sketch of the case, which is subsequently manufactured using a specialist.

Selecting the control radio roll, should not save on it, since the quality of this part does not directly affect the convenience of controlling the vehicle.

Of course, one of the most important components of the machine is its engine. Gasoline samples require careful care, but their capacity indicators are the highest.

Thus, it is safe to say that it is possible to collect the machine on the radio control, which is functioning with the help of fuel, it is quite possible, the main thing is to have a desire for this and the entire list of details.

With your own hands - many this phrase is associated primarily with the jigsaw for metal, a soldering iron and other Handmaider tools. Make your own model from an absolute zero - pulling out each item on your own - it is really possible, but it is quite complex, time-consuming and very demanding to our own skills process. So now we will talk about easier and available option: as collect Radio-controlled car at home.

How it works?

Modern models on radio control can be divided into two large groups:

• RTR.Fully ready for use of the machine ,. That is, it took out the model out of the box, put the battery - and forward, on the racing;
• Kit. Supplies for advanced users: Instead of the assembled machine, a set of spare parts comes to which you add your own - custom - spare parts, collecting the model of your dream independently.

Note : A variant in which you buy all parts separately, is not much different from. You just do not use ready-made sets, but, nevertheless, you use factory parts.

Why do you need an RC model with your own hands? Exactly the same as any custom: to stand out in the crowd, make your car unique. Moreover, the assembly of finished parts is less demanding of the skill than "work with a file".

What parts will be needed?

As a rule, if you chose some kind of Kit, then only the chassis and body included in its package. Additionally need ( we consider the option with an electric machine):

• Engine;
• Radio equipment: control panel, receiver, telemetry;
• Wheels;
• Battery;
• Disks, inserts, etc.

Ultimately, it all depends on the specific set for the assembly of the radio-controlled model of the machine with their own hands: in some, for example, there is no body, and it is purchased separately.

Is it difficult to collect Kit?

It is at the stage of assembling Kit'a difficulties usually does not occur: the details are numbered, it includes a detailed instruction to them - do everything neatly, and there will be no problems. Difficulties most often arise at combining the chassis with the rest of the components, so we advise you again: before buying the engine and other spare parts carefully Explore the selected Kit and its characteristics. Excellent choice Will read themed forums: certainly someone worked with this kit - and most likely, this someone willingly share experiences.

Plastic or aluminum?

The answer to this question largely depends on what brand is we talking about, but about it below. If you compare "in vacuum" - and good Plastic S. good Aluminum - the picture looks like this:

• Plastic: Lighter, it is better to shove the blow, restores the form after the collisions. But, at the same time, if the plastic is too strong, plastic cracks and breaks, it will be fixed almost unrealistic - the item is under replacement. In addition, on plastic parts over time, it is cleared planting shafts and bearings, because of what the backlings arise - it is necessary to change the item again;
• Aluminum. It is possible to repair and is practically not deformed over time, but good aluminum costs more than good plastic. Bad aluminum is usually rather fragile and literally scattered at the level of load level, which will not even notice high-quality plastic. And it is about the same.

Spare parts manufacturers

You can highlight the three most interesting brands:

• RPM.The best plastic on the market. Ideal quality, high strength, exceptional durability - what you need to make your own hands with a uninstalled RC model. The deficiencies of the brand are only two: high price and obvious sharpening for American cars like, on the "Chinese" spare parts RPM, most likely not to put;
• Integy. Aluminum details, good balance between price and quality. If you still prefer metal plastic, it is quite possible to think about choosing this brand. Well, yes: Aluminum looks cool!
• Pro-Line. Another excellent one - and quite universal - brand. Optimal choiceIf you are going to work not with American kit. Among the advantages of the brand: 5 years on the market, a bunch of awards, a very wide range and acceptable pricing policy.

​​​​​​​

General conclusions for machines in managing their own hands

If you carefully follow the instructions and do not rush, in self-assembly The RC model is not sophisticated. The main thing is to use high-quality components from famous brandThey fall into their seats trouble-free. Well, we recommend starting with Kit'a simpler, and then, after having received the first experience, lay the Castoma bar.

Some people even having become adults did not lose interest in different games. Someone collects the designer, someone plays in board gamesAnd someone very much like machines on the remote. Of course, this passion has a more adult, compared to the nursery. And many fans machines dream about to get such an exhibit to themselves, which will not have anyone in the world. Nothing is simple! Learn how to make a machine on the remote yourself.

To begin with, you need to decide which details will be necessary to create a machine. So that you missed anything, below is located, the list of necessary components:

• Electromotor or gasoline engine
• Body
• Chassis
• Wheels
• A set of screwdrivers of different sizes.

Making a typewriter with your own hands, you can control the entire process of creating, and then you will get exactly what they conceived. Plus, you will save money, and if you put a case on stream, you can do well on this. First, decide on the amount of money you can spend to purchase parts for the machine. The cost of the same types of components may vary depending on the material and quality of the product. Do you want to make a machine on a control panel with wire or on radio control? Here, when choosing, you need to consider that the parts for the wired console will be somewhat cheaper.

Wheels and chassis

Now you need to provide a chassis typewriter. You can try to make it yourself, but it is better to buy it ready in the store. Moreover, the wheels are sold with the chassis. When buying, pay attention to the quality of the product. The front wheels must turn with ease, and the tires are better to choose from rubber, because they give best clutch With expensive.

Engine

Now you need to choose the engine of the machine, and this is perhaps the most important thing, because the motor is the heart of the car. You can use an electromotor from some technique, and if there is no such, then go to the store again. There can also be purchased and a gasoline engine that is much more powerful. True, it is necessary to care for it, buy gasoline, and it costs an order of magnitude more. So it is worth staying on the electric motor, and it will save you money and time.

Remote Control

Now it's time to take up the control panel. If you decide to make a typewriter with a wired console, do not forget about its main drawback - the car will move only at a distance that will allow, the length of the wire. If your choice fell on a radio control, then for the assembly of the remote you need a radar. Despite the fact that it is not so cheap, it is better to acquire it, as this will allow you to control the machine at a fairly large distance that covers the antenna.

Body

The next point is the body. Here you can show all your creativity, and make it yourself, pre-drawing sketches. Although this item can be purchased in the store.

Assembly

Now we have all the necessary details, and you can start assembling. As a rule, detailed instructions are attached to the components. The whole sequence of actions is described. Then make the adjustment of the motor and the installation of batteries and the antennas, and only then you need to attach the body and chassis.

Now you know how to make a typewriter on the control panel.