How to replace the side mirror with your own hands? How to replace the side glass in the car with your own hand tools and materials for replacement.

How to change mirror element on the mirror rear view Vaz- 2110

Some sources by car VAZ 2110 This is quite difficult, and there is a possibility of damage when it is replaced. The owner of the tensor can prove the opposite

All this garbage. Everything changes in 3 minutes! I scored an hour when I was in a hurry, I waited until the car was warm up and caught up, the mirror completely shot. At the same time, from the inside the triangle under the mirror,

Photo 1. On the left. Explosive item on the right. New for 35 UAH in the nearest auto shop

Photo 2. From the inside to unscrew the handle of the lever of the mirror regulator.

Photo 3. From the inside we see such a picture.

Replacing the side mirror of the rear view VAZ 2110, 2111 and 2112

Video Replacement Example side Outdoor rearview mirrors on VAZ 2110., 2111 and 2112 do it yourself.

Replacing the side mirrors of the rear view on the VAZ 2110

replacement side Mirror on vAZ 2110. , 2111,2112 and so on.

Photo 4. The factory even took care. clung to a piece of noise!

Photo 5. Well, this is a procedure.

Photo 6. This white regulator plate.

Photo 2. (One bolt under the fork), then remove the plastic case (theoretically, it is attached to three "pistons", but after I took off the lever, immediately retired!) And unscrew the three bolts of direct mirror mounting.

Photo 3. glue-noise, pour under the seal of the side window (the holes can be pierced with a screwdriver, "noise does not interfere with the installation")

Photo 5. Scare from the complexity, but everything is simple for pain: We push the finger until you stop the point to the point "1", and then omit the finger at the point "3", pulling slightly, mirror element Easy is removed. Do not pull out mirror. And that's it. Everything is shot without prejudice and chop.

Photo 6. Remove mirror element In the middle of the middle slightly press it with a fist (or something else on the area more than 5x5 cm) until it clicks.

Everything else is collected and screwed up in reverse order. And if you do not reach him, itself mirror It should be very tightened, it will vibrate on blows and will not be able to resist even with the weakest attack of Vandala!
And for quality do not scold. I do not wear my digital with me always.)))
Good luck and even roads!

Read

We change the timing belt on the Chevrolet Cruise on its own power distribution mechanism of the vehicle is a fundamental node in the works of the car. If the passage of the vehicle breakdowns the machine will be impracticable. You should attempt to pay attention to the performance of the mechanism. Such a material will help figure out how the process of changing the timing strap timber ...

At first glance, the replacement would seem simple, but when to see how it was established, it can be understood that you still need to understand the electronics. Let's tell about the variety, the principle of replacement and the cost of the process.

The content of the article:

To date, it is enough to prevent the lack of side mirrors on any car, since most of their drivers use them. Although the early one could only dream about them. The side mirror in a modern car, including in Audi, is not only one of the elements of the machine, but it still performs the role of an "helper" during the vehicle movement. More precisely, it is they who help the driver to see the whole "picture" from behind the car (see).

Variety and a set of lateral mirrors

Modern manufacturers of foreign cars, such as Audi, improve the side mirrors as soon as they please. For example, we can safely say that they are such a complex of instruments, that is, in the side mirrors, the sensors, cameters, turn signals, heating, and more were gradually started to embed into the side mirrors.

The side mirrors on cars "stuff" not only heating or electric adjustment, but also equip the automatic folding function. This device will help to avoid damage to the side mirror at that time, the other car will pass nearby, or when the pedestrian will pass.

Quite often on the streets you can see such a car as AUDI, or any other foreign car in the lateral mirror of which the sensor "Dead zone" is built into. This sensor works and thus gives you to know motorists about the approaching moving vehicles, which is not reflected in the side mirrors. Such signals often remove from sudden steering action. First of all, such devices are needed for long SUVs, which need a certain distance for a particular action.

Most side mirrors in appearance are uniform, but their components inside and different functioning. That is, the composition of one can be built-in heating, and in the other this function and the mechanism may be absent. As a rule, it all depends on the initial configuration of the car (in this case, Audi), during the purchase, or on which mirror it was changed.

When the motorist had a desire to replace the side mirror, then professionals of their business advise to establish something that has a similar package with the previous one. This can be determined by how fasteners are installed because it must match the fastening principle with the previous one.

In replacing side mirrors, it is necessary to concentrate its attention on the connection of parameters, since it is important to connect the wires. If the motorist does not follow the instructions for the correct connection of the wires, instead of the automatic folding of the mirror, it is possible to enable heating, or turn on the adjustment instead of the rotation signal. Then the trouble on the road can not be avoided.

In this situation, with the replacement of lateral mirrors, it is best to ask for help for professionals in a special auto operator or to a service center in which you can order a side mirror with similar fasteners, which wizards can replace without problems.

But here is not everything smoothly, since the right side mirrors are not always in stock. This can be determined by the appearance of the element, which is not the corresponding body painting. That is why it is necessary to order a side mirror and necessarily indicate the labeling of a straight-colorful coating.

With such a replacement of side mirrors with order and installation in a specialized place, it is always worth considering the fact that it will noticeably hit the pocket. And if the mirror has many additional and newest functions, then the sum will, at least, double.

Therefore, because of the cost of the order and installation of side mirrors for some car enthusiasts per service station or in the service center, most drivers are managed to install them at home, since this process is not quite complicated.

To install the side mirror at home, it will be necessary to find a similar to the previous mirror. It is usually possible to be ordered in the service center, on the auto disassembly or search for the Internet. Quite often they are searched for the serial number, which is indicated or on the surface of the mirror, or in the service book to the car. When completing the order, it is recommended to "take" two side mirrors at once. This is primarily necessary for the new one not different from the old one.

Replacing side mirrors Audi

After the side mirror for the Audi car fell into the hands of a motorist, you can begin the replacement process. First, it is necessary to de-energize the entire car with the removal of terminals from the battery. It will help to protect themselves from shocking, as the wiring harnesses are held in new cars, even in the doorway.

First, the lateral mirror on the Audi on the driver's door is replaced, since the driver most often uses it when driving. The first thing to do is to remove the side mirror plug from the inner side of the door. For such manipulation, you will need to pry and disconnect the latches. This action is best carried out in the warm season, or in a warm room, because when the latch is cold, you can burst.

When the protection is removed, then it is possible that you can partially (not completely), unscrew the fastener of the side mirror. It is not completely unscrewed, since it still has to remove the wiring to the mirror in the event that it has been equipped with a functional. To disshinate wiring, you will need to remove the trim on the door. Obstacles for its removal may be additional attachments on the upholstery surface.

Here you need to do, as with the plugs specified above, that is, hide at the bottom of the latch. Sometimes manufacturers are too secured all the mechanisms, so it is necessary to be attentive because under the plugs there may be bolts that fix the entire design.

When the AUDI car's door trim was removed, it will be necessary to disconnect the sideways of the side mirror, and then you can also completely remove it from the machine. Next, without any fixation, you need to connect a new side mirror. To do this, throw the terminals on the battery and test it. Ideally, it should carry out the same features as old.

The chips are simply obliged to coincide in shape, and on wires in genuine side mirrors. In case, if the chip does not dock, then it will be necessary to remove it from the old side mirror and rearranged on a new, turning over the wires. As a rule, the cross section of the wire makes it possible to rearrange everything without loss of functions. But here without additional knowledge in electronics in this case will not cost, since it is necessary not to confuse the power and wires in some places.

Check is completed, and now you can go to the assembly. After disassembly of the mounted installation, it should be safely started directly to the assembly. Next, you should skip the wires through a separate specifically reserved hole, and it is also necessary to fix the side mirror to the door frame.

Then it is necessary to connect chips according to the trial, attachment. It is recommended to combine chips to the frame of the door with two-way scotch. This is necessary so that they do not prevent the normal operation of other parts in the doorway, and so that the friction process is not arose about the windows and other elements. These mannewers will help increase the service life of the wiring, and the assembly process will be much simplified.

After taking all the above, you can start assembling the door of the door. But here you need to be extremely careful and attentive, since all the wires and chips of the side mirror of the Audi car to the control unit. It is in, and on the doors there are many control mechanisms and the buttons of the entire machine. The first thing is that it is recommended to double-check the operation of all buttons and mechanisms, and already begin to assemble the plating by the method of snatching it in a circle. This recheck will help avoid unnecessary covering.

With the replacement of the side mirror on the door of the driver on the Audi car, you can end. In order to change the side mirror on another door from the passenger side, you need to do the same algorithm.

In replacing the side mirror, it is important to choose the correct element of the replacement, as it can be different because of its color marking or the year of the car is out. Maybe for someone from motorists, they are not the desired part of the car during a ride, but their absence on the door can entail a penalty in the door if the traffic police inspectors will notice.

Side Mirror Replacement Price

When the motorist decided to replace the side mirrors at home, he will need to pay only the mirror itself and a little more for additional materials, in case they are missing at home. Purchase one will cost for a driver at least $ 35 per unit. But here it all depends on the year of the car Audi.

But if you do not count on your own strength and opportunities, then the replacement of each side mirror on the Audi car on a specialized service station will start from $ 15. Therefore, before the replacement process, one point should be understood before the replacement process: "Will the wallet" pulls "the wallet, or at the maximum.

Video on the installation of the side mirror:

Change the side mirror simply. It is necessary to squeeze and remove the angular plastic pad from the inside of the door, separating the terminal by pressing the plastic focus along the terminal, unscrew the 3 nuts fixing the mirror bracket. Repeat everything with a new mirror in reverse sequence. From nuances:

1. The plastic corner pad is better to start pressing from above, while leaking a flat screwdriver over the projection of the upper heel. When it is tempered by 3-4 mm, do the same with the bottom. And she will easily go away.

2. Nuts are better to boo in a cylindrical head by 10 mm. On the last turns you need to be careful not to drop the nut inside the door.

3. The gasket on the new mirror before installing, you need to fade along the back side so that the bolts come out on the other side to the same distance.

4. Tighten the nuts in a circle of 1-2-3 sequentially 1-2 turns so that the land laying is uniformly. Landing is visible because tightening tightly screw 1, after a broach 2 and 3 in 1 again there is a free course.

Projection of studs on the reverse side of the lining:

View after lining:

Unscrew the nuts do not carefully, so that the door did not fall.

Through the square hole removed the mirror connector.

The mirror is removed with a large triangle.

That's how I was broken by the mirror:

After installing the mirror:

Thermofilm on the back of the mirror:

Frame of fastening of a mirror element:

If you remove the element itself, then it is necessary to rotate the glass of the mirror so that the gap between the case and the mirror element itself appears. It is better to warm the hair dryer, and then the latches are tight.

Selling view:

Motors electric drive.

Mirror in analysis

Disassembled "on the bones" the old mirror. It became clear how everything works and where the source of the grain ratio at high speed ("clap" the discharge zone on the back of the case). If short, then the situation is as follows. The node from the housing to the mirror canvase is assembled sequentially, and the plastic plate itself with glued glass is riveted at the very end.

At the same time, apparently, back it to decline in general the form is very problematic! It is necessary to put pressure from the grooves, and they are under the glass! If you broke - there are no problems, with a decent effort it will populate, but to disassemble without damaging and then snap back .... unlikely.

And the cause of the beating is simple. There, the plate with a mirror is attached to the moving roller, which on one side is fixed to the side of the ring with a spherical base and is held with a small pin, inserted into the hole in this side, and on the other - to the gear brackets, which, when rotating the axis 2 parallel engines, pushed out the axis Kulisa Kanaba or the opposite is drawn inside.

The scene and the support ring are rigidly connected, and the ring after the scene is freely moving forward-back turning the mirror. And he cuts all this (and in theory should prevent vibrations) Hollow rubber ring (in the photo on the left):

But it is with thin walls and very soft. I think in the cotton air at the rate of its elasticity becomes not enough. The solution is like a simple - to increase the elasticity of the rubber ring (for example, inserting the foam ribbon inside it).

But, I repeat, get there and disseminate from the stops mirror without damaging the glass is unlikely to succeed! So IMHO is easier not to risk and not tortured to disassemble the mirror, but, as the VID offers, adjust the position and pour the edge of the glass with a rubber band inserted in the neck between the glass and the case.

A few more pictures without comment:

To maximize the situation on the road, any car is equipped with mirrors. There are two side mirrors and salon (rear view). As a result, the driver can overlook the road situation for all 360 degrees.

In the process of operation, auto may occur when the integrity of the mirror is broken. For example, they are deformed as a result of an accident or they can simply steal for subsequent sale. Also, the driver during parking or with any other maneuvers can hurt the mirror so that it is necessary to change the side mirrors on the VAZ-2114. Let's find out how to replace these items that they happen to how to install heated and how to make tuning mirrors - it will be useful for novice car owners.

Right choice

Many domestic cars are constantly wondering how to choose side mirrors on VAZ-2114. The fact is that the various manufacturers offer these products, the mirror element itself may be of various quality. As a result, they have different specifications.

Specifications

Manufacturers are constantly trying to produce a car mirror with modern reflecting elements, equip them with a heating system and electrical drives. All this makes it possible to significantly improve the life of the owner of the Lada car brand. A good mirror increases safety many times.

Modern products can be characterized by an increased level of visibility, the presence of special anti-glare coatings, a clear and high-quality image, a convenient and reliable system of adjustment.

A sufficient visibility for automotive mirrors is achieved using a combination of a form, size, as well as the level of curvature of the optical reflecting element. The position of the mirror is also serifted. From the review, much depends on the higher, the more information about the situation will receive the driver.

Young car enthusiasts like to equip their cars with xenon optics. At night, Xenon is very blinded by other drivers through the side mirrors on the VAZ-2114. To prevent even minimal blinding, a special liquid crystal layer is introduced into it, which, when exposed to bright light, reduces the intensity of the reflected light and allows the driver to protect the driver, thereby helps to avoid accidents.

A clearer picture that is visible to electric mirrors is ensured by a special reflective layer. Previously, it was applied only on the inner surface of the reflecting element - even with a strong contamination, the driver saw a distorted image. Modern manufacturers produce mirrors of the side type of VAZ-2114 with a reflective layer on the outside.

on the VAZ-2114 and their shortcomings

The car is completed with products with durable and fairly reliable fastening, but with all this elements have a whole mass of quite serious flaws. The main minus, which is distinguished by the standard side mirror of the VAZ-2114, is a bad review. Also, the disadvantages include a small amount of adjustment options, and it also trembles when driving.

Especially intense trembling can be observed when driving on bad roads or off-road. And everything would be nothing, but constant vibrations lead to the fact that the plastic pad comes into disrepair. And in view of the fact that the side mirrors of VAZ-2114 have not too successful design, most of the road simply is simply visible. By performing maneuvers, the driver must be distracted to make sure that there is no interference through the windows. Customize the position of the mirror The manufacturer offers using a mechanical lever - this is quite convenient, but this method is primitive and does not allow you to get the desired angle of inclination when all or at least most of them are available.

Also on standard models installed the most simple wedge antambolite system, which is not particularly efficient. In the dark, this primitive protection system from glare does not allow the driver to accurately assess the distance to the nearest vehicle and its overall dimensions.

In addition, in the winter period, the mirror and all its components are covered with ice. And to clean them, you need to make a lot of effort. Replacing the side mirrors VAZ-2114 to more modern will help solve all these problems. The market offers a wide selection of alternative models that are ideal for these cars.

Alternative options

In automotive stores, products are often found with cable adjustments or electric mirrors. They implemented the functions of folding. In addition, side mirrors are offered on WAZ-2114 heated. There are modifications protected from blinding and with rotation repeaters.

The most famous and popular manufacturers are the NPK "Polytech", as well as the company "Ergon". Often there are both high-quality models from Japanese brands. Such a replacement of the side mirrors VAZ-2114 will not be difficult - it can be done without refinement. The product, regardless of the manufacturer, has a massive base in fastening places to the car, which significantly reduces, and even prevents vibration and shaking at all.

Cost and equipment

Approximately the price of one such mirror begins from 700 rubles. Cost can vary significantly depending on the configuration. New left electric mirrors appeared on the market with an aspheric reflective element, while the right - ordinary spherical form.

Electrical mirrors of such a plan are in a special protective cover - it allows you to securely protect the glass of the mirror from any damage. Also, these models have anti-grappling reflectors of various shades. Included there are lining. They are from black plastic, and immediately can be painted in the body color. Sell \u200b\u200boptions specifically for tuning lovers - with rotation signal repeaters. Such details will add attractiveness and uniqueness to the appearance of the machine.

Models with electric drive and heating

These solutions are now very popular. You can manage the position using special joysticks.

The heating function adds comfort and convenience. With the help of it, you can cope with frozen mirrors in a heavy frost and with contamination of reflective elements during the snow or rain.

Dismantling mirrors on VAZ-2114

First of all, you need to disassemble the old mirror. This is not a challenging task, and for its execution only a regular screwdriver will be required. To begin with, you must pry a plug that is on the mirror control knob. It is a screw under the Cross screwdriver.

Next, the plug is cleaned - on the VAZ-2114 it holds on the locks. Minus screwdriver to deduct the locks are very simple. Three screws are under the decorative plug - if you unscrew them, the product can be removed.

This task, how to replace the side mirror on the VAZ-2114, is solved simply and elementary. For this, many people love cars of Russian production - repair can be performed using the minimum number of tools and without much experience. To install a new mirror, you need to do all actions on the contrary. It will not be difficult.

How to disassemble lateral mirrors

Sometimes a complete replacement of the sideways mirror VAZ-2114 is required. It is possible that everything will be installing a separate element on the left or right side.

Let's see how you can disassemble the design as little as possible. At first it is necessary to press from the inside to the plastic case. The holders carefully decline with a flat screwdriver. This method is not too reliable - there is a considerable chance that the mirror element or other details will break.

The second option carries more risks - here you need to quickly hit the glass about the surface (but it is better if it is soft). This is a quick option for dismantling and replacing the element. The blow should be light and fast. To replace the plastic case or main fasteners, get adjusting thrust and pin. The assembly is performed exactly to the opposite.

Installation of heated elements

The installation of side mirrors on the VAZ-2114 heated is carried out differently. The installation kit has a marking template on paper. It should be attached to the door and with the help of sewing transfer the markup to the car door. Then the adjusting mechanism is fixed through the puck. Next, three screws are screwed down, while the upper must go through the hole in the adjustment mechanism. Then the adjusting handle is installed.

Heated mirrors

There are options here - you can purchase a ready-made tuning mirror or separately buy an element for heating and install it yourself. At the cost of such tuning will cost several rubles, and in terms of efficiency the project will pay itself in millions of times.

Heating from incandescent bulbs

So, one light bulb at 21 watts of power can literally for a few minutes to defrost even a very frozen mirror.

If one lamp is not enough, then you can apply two to 10 W or one, but with two contacts. One is intended for defrosting, the second will be used to protect against fogging. This feature will not save you in the rain or snow.

Connecting heating

Often the heating element leaves two wires. You can connect them as you like. Since the heating should be heated with the heating of the rear window, then the cords from the mirrors can be attached directly to this item. If you need to warm the mirrors regardless of the rear window, then you will need a relay and the power button, as well as the fuse at 10 A. If the button is calculated for 10 A, you can do without relays.

The heating system from undergraduate materials is made using a light bulb. This is the most universal solution. It is necessary to finalize the case - there are made from foil. Further, the cartridge is placed with a light bulb and attach it there so that the lamp does not touch the housing or the mirror.

Summary

Thus, it can be replaced or modified at the request of a car mirror. Some acquire solutions with electric drive - it is very convenient. You can equip it with heating and with your own hands. In both cases, there will be no problems in winter.

By the way, an ultrasonic purification of glasses was used on the Toyota Crowon cars of the 90s. Thus, the ice, accumulated on the surface, was filming from it in a matter of seconds. However, most manufacturers preferred to install precisely electrical heating, including AvtoVAZ (of course, as an option). However, you can add this feature using a conventional light bulb.

So, we found out how to change the side mirror on the VAZ-2114 with their own hands without much effort.