Renault symbol driver seat does not move. Renault Symbol

Before starting movement, adjust the seat position. In order to adjust the longitudinal position of the seat, lift the lever of the lock, located in front of the seat cushion. Holding the lever, slide the seat forward or backward at a convenient position for you. Then let go of the retainer lever. To check the reliability of the seats fixing, try to move it back and forth.

To change the sliding angle of the seat back, lift the lock lever, located on the side based on the seat cushion (from the door side). Holding the lever, bring the back at a convenient position, then release the retainer lever.

In this case, the back will be fixed in a new position.

To ensure the convenience of planting passengers to the back seat and their exit from the car backrest of the front seats can be tilted forward. Clamping handles are located on the side of the backs of the seats (from the doorways).

Adjusting the backlock front seats It is carried out using a rotating handle (rear), which is located on the side based on the seat cushion.

Driver seat cushion height adjustment (separate models)

Driver seat cushion can be adjusted in height. The adjustment is made by rotating the regulator, which is located on the left on the base of the seat cushion.

Electric driver seat adjustment (separate models)

Your car can be equipped with a driver's seat with electrical adjustment drives. The two electrical adjustment switches are located on the left on the base of the seat cushion. The combined switch with a long horizontal handle is designed to adjust the longitudinal and vertical position of the seat, and the switch with a short vertical handle for adjusting the backing tilt.

The seat can be adjusted at any key position in the ignition lock. Before starting movement, adjust the seat position.

Press the knob of the combined switch forward or back to move or remove the seat from the steering wheel and the control pedals.
Press up or down to the front end of the combined switch handle to lift or lower the front edge of the seat cushion. Similarly, press up or down to the rear end of the combined switch handle to lift or lower rear part Seat pillows.
To lift or lower the seat cushion, press up or down to the central part of the circuit breaker handle.
Adjust the tilt of the seat back, rejecting the vertical handle of the switch to the appropriate side, which is located behind the combined switch.

Headrests

Headrests are installed on the front seats. On some modifications of the car head restraints are also installed in the rear seat. Headrests help prevent neck and head injuries. In order for the head restraints to perform their protective functions, they must be properly adjusted. The upper part of the head restraint cushion should be on the same level with the upper edge of the ear shell.

On some modifications, the car provides the ability to adjust the head restraints in height. Adjusting the head restraint is made by two hands at the same time, so you should not try to adjust the headrest during the movement of the car. In order to raise the head restraint, just pull it up. Unlike this, to lower the head restraint, you must first press the button of the retainer.

Disassembling the headrest for cleaning or replacement is made as follows. Raise headrests to the end. Then click on the lock button and remove the headrest with the seat back.

Folding back rear seat (separate models)

The back of the rear seat is made separate, and consists of two parts that can be folded forward, opening direct access to the trunk. Rear seat backrest fixtors, locking it in a normal position, can be released both from the car and from the trunk.

Each of the two sections of the rear back can be folded forward regardless of another.

Turn the clamping knob clockwise to fold the left section, or counterclockwise to fold the right selection of the back.
In order to fold the back of the rear seat from the trunk, pull the locks that are located under the rear shelf.

After returning the rear seat back sections to a normal position, highly press them towards the rear shelf to fix on the spot. Check out the reliability of the rear backrest lock, pulling the top edge of the back of yourself. After returning the back of the rear seat to the vertical position, check that the straps of both diagonal belt belt be over the back.

Make sure that all things that are in the trunk or protrude from the trunk to the car's salon are securely tied. Locked baggage can break from the place and injure the driver and passengers in case emergency braking car.

Cars with 3-door Body Hatchback

In order to fold the rear seat back sections (simultaneously or separately), lift the lock button, which is located on top on each section.

Cars with 5-door Hatchback

Before pressing the backs sections, turn the rear seat cushion into a vertical position so that it gets up behind the front seats. To do this, use the loop attached to the rear seat of the seat cushion. Remove headrests from the back and insert them with pins into the holes, made at the base of the seat cushion. Then fold the rear seat back sections.

You should not move with an open lid of the trunk and a folded back of the rear seat, while there is the possibility of carbon monoxide poisoning (CO).

Headrests

Related position

If you have a passenger in the back seat, you should not leave the head restraint in a completely omitted position.

Adjustment in height

Click on the lock 1 and simultaneously slide the headrest.

Removing the head restraint

Installation

Insert the headrest rods into the holes of the guide sleeves so that the grooves on the rods are facing the front of the car, and install the head restraint to the desired height.

Since the head restraint is one of the elements of safety, follow its presence and proper installation: The top edge of the head restraint must be as close as possible to the top of the head.

Moving seats back or back

To unlock the seat, lift the bracket 1 or lever 3.

After installing the seat in the desired position, release the lever or bracket and check the reliability of the selection fixation.

Driver seat height adjustment

Use the lever 2.

For security reasons, make all adjustments on the car.

Adjusting the tilt seat back

Rotating a handle 5, set the seat back to the desired position.

Seat with heated

(Depending on the vehicle modification)

When the engine is running, press the switch 4. In this case, the warning lamp lights up in the switch.

The system stabilizing the temperature determines whether heating is needed or not

In order not to reduce the effectiveness of seat belts, it is recommended not to tilted the backrest of the seats too back.

On the floor (before the driver) should not be any objects, t. In case of sharp braking, they can get under the pedals and prevent them from moving.

in order to ensure safety at the time of movement, always fasten the safety belts. In addition, comply with the requirements of the rules road The country in which you are.

Before running the engine, adjust the driver's seat, then places for all passengers, adjusting seat belts to ensure the best protection.

Incorrectly adjusted or twisted seat belts can cause injuries at an accident.

Use safety belt Only for one person, baby or adult.

Even pregnant women should be fastened with a seat belt. In this case, it is necessary to ensure that the pelvic branch does not give a lot to the bottom of the abdomen, but did not save.

Adjusting the driver's seat

Sit deep into the seat (removing the coat, the jacket, etc.). This is important for the right back position.

Adjust the seat position relative to the pedals. The seat must be pulled in as long as possible, but so that it is possible to click on the clutch pedal until it stops. The back of the seat must be installed in such a way that the hands holding the steering wheel were slightly bent in the elbows.

Adjust the position of the steering wheel.

Adjust the position of the head restraint. For the greatest security, the distance between your head and the headrest should be minimal.

Adjust the seat position in height. With this adjustment you will achieve best Review Through windshield.

Adjusting seat belts

Sit on the seat, completely leaning back.

The shoulder branch of 1 belt should be located as close as possible to the bottom of the neck, but do not lie on it.

The waist branch of the belt 2 should fit tightly to the hips and hold the pelvis.

The seat belt should fit the body as close as possible. For example, do not wear with a car bulk clothes, do not put any objects under the belt and T d.

Signal Safety Lamp Driver Safety Lamp

The lamp lights up with a permanent light, when the speed is reached about 10 km / h, the lamp flashes approximately 90 seconds and a beep is fed, then the lamp is on the permanent light.

Safety belts on the rear seats

Rear side belts 1

Fastening, disassembling and adjusting the seat belts of the rear seats is performed in the same way as for the safety belts of the front seats.

Rear middle seat belt 3

Slowly pull the strap 2 of the nest.

Latch the black buckle 4 in the black lock 5.

In completion, snap the sliding buckle 6 in the red lock 7.

To ensure the effectiveness of seat belts, make sure that the seat fixation is reliable. See "Back Seat: Functional Features", Chapter 3.

Additional security device

Rear side belts are equipped with a tension force limiter.

This device is turned on with a certain impact force to limit the pressure of the belt pressure on the body.

Belt branch seat belt with manual adjustment 8

The belt must fit tightly to the thighs and hold the pelvis.

The seat belt should fit the body as close as possible. For example, do not wear with a car with bulk clothing, do not put any objects under the belt and T d. For belt tension, pull the free end of the 5 strap.

To weaken the belt tension, set the adjuster 11 perpendicular to the belt, click on the knob to the side of the bracket and at the same time pull the belt branch 10.

The information below relates to the safety belts of the front and rear seats of the car.

Do not use anything to loosen the belt fit to the body (for example, clothespins for linen, clamps, etc.): The safety belt, which is too loose, can cause injury.

Never skip the shoulder branch of the belt at hand or behind the back.

Do not use the same belt to wear a few people and in no way fasten with one strap together with the child sitting on your knees.

The seat belt should not be twisted.

After the accident, check and replace the belts if necessary. The replacement should be made in the event that signs of wear or damage appeared on the belts.

When installing the rear seat in place, follow the correct refueling of seat belts so that they can be used for their intended purpose.

During the movement of the car, if necessary, adjust the position and tension of the belt.

Make sure that the belt buckle is inserted into the appropriate lock.

Related position

If you have a passenger in the back seat, you should not leave the head restraint in a completely omitted position.

Adjustment in height

Click on the lock 1 and simultaneously slide the headrest.

Removing the head restraint

Installation

Insert the headrest rods into the holes of the guide sleeves so that the grooves on the rods are facing the front of the car, and install the head restraint to the desired height.

Since the head restraint is one of the elements of security, follow its availability and proper installation: the top edge of the head restraint must be as close as possible to the top of the head.

Moving seats back or back

To unlock the seat, lift the bracket 1 or lever 3.

After installing the seat in the desired position, release the lever or bracket and check the reliability of the selection fixation.

Driver seat height adjustment

Use the lever 2.

For security reasons, make all adjustments on the car.

Adjusting the tilt seat back

Rotating a handle 5, set the seat back to the desired position.

Seat with heated

(Depending on the vehicle modification)

When the engine is running, press the switch 4. In this case, the warning lamp lights up in the switch.

The system stabilizing the temperature determines whether heating is needed or not

In order not to reduce the effectiveness of seat belts, it is recommended not to tilted the backrest of the seats too back.

On the floor (before the driver) should not be any objects, t. In case of sharp braking, they can get under the pedals and prevent them from moving.

in order to ensure safety at the time of movement, always fasten the safety belts. In addition, comply with the requirements of the rules of the road of the country in which you are.

Before running the engine, adjust the driver's seat, then places for all passengers, adjusting seat belts to ensure the best protection.

Incorrectly adjusted or twisted seat belts can cause injuries at an accident.

Use the seat belt only for one person, child or adult.

Even pregnant women should be fastened with a seat belt. In this case, it is necessary to ensure that the pelvic branch does not give a lot to the bottom of the abdomen, but did not save.

Adjusting the driver's seat

Sit deep into the seat (removing the coat, the jacket, etc.). This is important for the right back position.

Adjust the seat position relative to the pedals. The seat must be pulled in as long as possible, but so that it is possible to click on the clutch pedal until it stops. The back of the seat must be installed in such a way that the hands holding the steering wheel were slightly bent in the elbows.

Adjust the position of the steering wheel.

Adjust the position of the head restraint. For the greatest security, the distance between your head and the headrest should be minimal.

Adjust the seat position in height. With this adjustment, you will achieve the best viewer through windshield.

Adjusting seat belts

Sit on the seat, completely leaning back.

The shoulder branch of 1 belt should be located as close as possible to the bottom of the neck, but do not lie on it.

The waist branch of the belt 2 should fit tightly to the hips and hold the pelvis.

The seat belt should fit the body as close as possible. For example, do not wear with a car bulk clothes, do not put any objects under the belt and T d.

Signal Safety Lamp Driver Safety Lamp

The lamp lights up with a permanent light, when the speed is reached about 10 km / h, the lamp flashes approximately 90 seconds and a beep is fed, then the lamp is on the permanent light.

Safety belts on the rear seats

Rear side belts 1

Fastening, disassembling and adjusting the seat belts of the rear seats is performed in the same way as for the safety belts of the front seats.

Rear middle seat belt 3

Slowly pull the strap 2 of the nest.

Latch the black buckle 4 in the black lock 5.

In completion, snap the sliding buckle 6 in the red lock 7.

To ensure the effectiveness of seat belts, make sure that the seat fixation is reliable. See "Back Seat: Functional Features", Chapter 3.

Additional security device

Rear side belts are equipped with a tension force limiter.

This device is turned on with a certain impact force to limit the pressure of the belt pressure on the body.

Lower seat belt branch with manual adjustment 8

The belt must fit tightly to the thighs and hold the pelvis.

The seat belt should fit the body as close as possible. For example, do not wear with a car with bulk clothing, do not put any objects under the belt and T d. For belt tension, pull the free end of the 5 strap.

To weaken the belt tension, set the adjuster 11 perpendicular to the belt, click on the knob to the side of the bracket and at the same time pull the belt branch 10.

The information below relates to the safety belts of the front and rear seats of the car.

Do not use anything to loosen the belt fit to the body (for example, clothespins for linen, clamps, etc.): The safety belt, which is too loose, can cause injury.

Never skip the shoulder branch of the belt at hand or behind the back.

Do not use the same belt to wear a few people and in no way fasten with one strap together with the child sitting on your knees.

The seat belt should not be twisted.

After the accident, check and replace the belts if necessary. The replacement should be made in the event that signs of wear or damage appeared on the belts.

When installing the rear seat in place, follow the correct refueling of seat belts so that they can be used for their intended purpose.

During the movement of the car, if necessary, adjust the position and tension of the belt.

Make sure that the belt buckle is inserted into the appropriate lock.