How to change the fuel filter on Chery Tiggo. How to change the fuel filter on Chery Tiggo Fuel filter Cherie Tiggo 1.6

27.07.2020

In accordance with the recommendations of the manufacturer's plant, the fuel filter is replaced after 2 years of operation or 20 thousand km of mileage. However, taking into account the experience of the operation of cars in russian conditions We recommend replacing it every 15 thousand km of mileage. Rods when moving a car with a high probability indicate a clogging of the filter.

Fuel filter Located near the front right side of the fuel tank and is fixed on the base of the body, so it is more convenient to work on the car installed on the lift or observation ditch.
1. Reduce the pressure in the fuel supply system (see).

2. Squeeze the locks and disconnect the tip of the discharge fuel line from the filter.

3. Similarly, disconnect the tip of the supply fuel line on the other side of the filter.

4. Disconnect the wire shoe from the fuel filter.

5. Press the spring fastener spring ...

6 .... And remove the fuel filter.

7. Install the new fuel filter in the reverse order, so that the arrow on the cylindrical part of the filter housing coincides with the direction of the fuel flow.
The tips of the fuel hoses connect to the filter by the movement along the fittings before snapping the clamps.
A warning.
After installing the fuel filter, you must check the fuel filter connections with fuel lines using the gasoline leakage. If necessary, repeat the operation of connecting fuel lines to their reliable fixation. If the leaks from the compounds are not eliminated, replace the sealing rubber rings of the tips of the fuel lines or fuels assembly.

I decided to replace the fuel filter on my Chery Tigo, but I estimated that there is no store with spare parts for China. There are still shops designed for foreign cars, but everything concerns the Chinese have even consumables order and wait for a week.

I went to a regular auto parts store, that is, calculated for domestic auto industry. And here is not a filter than no worse and the more no longer differs in constructively.

The replacement of the fuel filter on Chery Tigo easily can be produced in garage conditions. Replacement takes no more than 20 minutes. Question price: ~ 200 rubles.

Replacing the fuel filter

Install a car on the lifting box (or call on the observation hole);
Find a filter. By car, Chery Tigo, he is located in the Renobook area (in front of him on the right side) and is attached to a plastic clamp;
Turn off the tube from it and using screwdrivers to dismantle the filter;
Install a new one, given the direction of the shooter on the filter with respect to the tubes;
Scroll the car key until the fuel injection. It is necessary that the filter starts to function. Repeat the procedure 3-5 times and after already start the engine.

Symptoms of worn filter

Jerks when driving at high speed (more than 90 km / h);
Caressing the engine;
Insufficient power and "aggression" of the car while pressed on the accelerator pedal.

The cleanliness of the fuel, which is commemorated by Ukrainian motorists, often leaves much to be desired. And not always in that fault manufacturers. Contaminated can be a transport tank or a bunker, in which gasoline is stored at a gas station. Dirt B. fuel tank It can get in and during the fill in it fuel.

For injector engines - namely, this is installed in - it is very important that the fuel used is clean. In this case, the nozzles will not be clogged with mud and gradually collapse and ensure uniform injection of the combustible mixture, and the engine will function in optimal mode and long delight the owner of the car by uninterrupted operation.

To clean gasoline as much as possible and applied. It exercises subtle cleaning, unlike the mesh installed in the fuel module at the inlet of the fuel pump, which produces coarse filtering.

What does not mean that the filter is time to change

The automaker recommends changing the Chery Tiggo fuel filter after every 20,000 mileage kilometers. However, in our country, it is often refueling for dubious quality, so this figure should be reduced to 15, or even up to 12 thousand.

Do not forget to do it in a timely manner. Otherwise it will be forced to pump fuel through scored filterSo he will have to work with an increased load, which, of course, will not benefit him. If the groove is coming from the gas tank, perhaps this is exactly the case. Although pollution can be in other places of the system. First of all, you should check the grid of coarse cleaning, which is in the fuel module along with the pump.

Too early clogging of the fuel filter may indicate the presence of garbage in. In this case, it must be washed.

Some changes in the behavior of the machine can suggest a likely clogging of the fuel filter. Power loss, interruptions in the operation of the motor, car jerking first will be noticeable mainly when accelerating or driving at high speed. Gradually, such symptoms are increasingly will occur at a slower movement.

How it is arranged and where is the fuel filter in Chery Tiggo

Fuel filter, which is used in Cherie Tiggo, is a direct-flow device. Inside the unsolved cylindrical housing made of stainless steel, placed, which carries out thin fuel purification. Special paper is used as a filter material. It is the quality of paper first of all distinguishes a good fuel filter from cheap fakes.

On the opposite bases of the cylinder there are intake and exhaust fittings through which the fuel output is carried out. In addition, there is a terminal for connecting the grounding wire (mass).

Since the filter has an unbalanced design, it is impossible to repair it. Consequently, it is necessary to simply replace the new one.

In Mark cars Chery Tiggo. The fuel filter is mounted on the base of the body in the gas tank area to the right of it. Because of this location, you can only get to the filter below. To work with it it was convenient, you can use the lift or observation pit. If there is no possibility, you can simply lie on the rug.

Independent fuel filter replacement in Chery Tiggo

Since you have successfully reached the fuel filter, then the procedure itself is hardly caused by your difficulties. If at least five hours passed from the moment of stopping the engine, then the pressure in the fuel system will fall almost to zero. Otherwise, you must first produce a forced reset of pressure, and only after that it will be possible to disconnect from the fittings.

To reset the pressure in the engine power system, you need to start the motor with a disconnected fuel pump And wait until gasoline remains in the fuel ramp.

Turn off the gas station in two ways.

The 1st way is to extract the relay responsible for the pump start. It is in the fuse box under the hood on the right side of the car

The 2nd method is to disconnect the connector with the feed wires in the fuel module. To get to it, you need to throw back backseat And raise the upholstery of the floor. Under it, detect the lidh cover under which the fuel module is located.

After removing the chip with the wires, you thereby devent the fuel pump.

Before disconnecting the chip, do not forget to remove the minus wire with the battery.

Now put the gearbox lever on the neutral and use parking brake. Run the motor. After a while, when the fuel remained in the system, it will stall.

Turn on the starter for a couple of seconds to equalize the pressure in the pipeline, return to the relay place (or connect the chip) and you can proceed to dismantling the fuel filter.

1. Squeezing the retainer, remove the tip of the fuel line from the outlet. The latch can have a serious resistance, then use the appropriate tool, such as a screwdriver. If the tip fails to shift the wrench as a lever.

2. Do the same on the opposite side of the filter.

3. Disconnect the ground wire from the housing.

If you want to replace ground wire, unscrew the head bolt to 10, which it is attached to the body.

4. Pull the device from the holder. To do this, you need to break the spring retainer.

5. Memontize new element in reverse order. In order not to make a mistake when installing, focus on the arrow on the device case, which indicates the direction of fuel flow.

Sometimes the arrow can show an incorrect direction. To find out exactly where the entrance is where the outlet is inserted into the hole of the fitting a long thin object, for example, a nail or a piece of wire. In the outlet, it will stumble on a rigid obstacle. There will be no such obstacle at the entrance.

Hose tips wear up clicks.

Check the tightness of the connection when the engine is running. If you notice the leakage of gasoline, try connecting the fuel lines again. If it does not help, change the seals in the tips or completely hoses assembly. Keep in mind that the hoses that are used in the engine power system are produced by special technology From materials resistant to lubrication and gasoline. Avoid using random tubes that are simply turned up. This can cause problems with the functioning of the fuel system, and sometimes even lead to a fire.

Do not chase for cheap

A cheap fuel filter often has a plastic housing that is not designed for a significant pressure present in the fuel system. It may also not withstand sudden temperature differences. As a result, such a device may simply crack, which will lead to at least the leakage of gasoline.

But manufacturers of cheap fakes are saved not only on the case. In the filter element, they use thin, fragile paper, which poorly cleans gasoline, passing a lot of dirt into the fuel ramp. It happens that it is simply rhat, and then almost no fuel is served on the nozzles. The nozzles scored by mud will immediately affect the stability of the functioning of the power unit.

Want to avoid similar problems - purchase devices made by a reliable manufacturer.