Special tools are required
Device for measuring wheel convergence, 64 x 60 mm (07MGK-0010100)

The suspension allows adjustment of the collapse and convergence of the front wheels and convergence rear wheels. However, each of these adjustments is made in accordance with others. For example, when adjusting the collapse, the wheel alignment changes. Therefore, it is necessary to adjust the position of the front wheels each time you adjust the collapse or convergence.

Preliminary check

For proper control and correction of the collapse / convergence of wheels, spend the following checks:

Checking the angle of tilt akvorn

Checking the angle of tilt a hundred front suspension

Adjusting the angle of tilt a hundred front suspension

The collapse of the front wheels can be adjusted when replacing the shock absorber plug bolts on the adjusting bolts of a smaller diameter. The gap between the diameter of the adjusting bolt and the diameter of the mounting bolt hole allows a small adjustment.

Checking the corner of the rear wheels

Check and adjust the convergence of the front wheels

Check and adjust the convergence of the rear wheels

Checking the ratio of angles of rotation of the wheels

2.

Pressed brake pedals turn steering wheel To the end to the left and right and check the angles of rotation of the wheels. If the angle of rotation is not within acceptable limits or there is a difference in the limit angles of rotation of the right and left internal wheels, go to. Angle of rotation: Internal: 15 inches diameter wheel: 40 ° 06 "± 2 ° Wheel with a diameter of 16 inches: 38 ° 46 "± 2 ° Outdoor (example): 15 inches diameter wheel: 31 ° 55 " Wheel with a diameter of 16 inches: 31 ° 14 "

Find out something new

Civic disk size (wheels)

Hub Honda Civic EJ9 1996 (1998) has 4 studs at a distance of 100mm. Planting 56.1mm. Departure from ET38 to ET45. This size is 4x100 is also on the body EJ8. Attention! Wase discs 4x98 with center 58.6 absolutely forbiddenThe centers of the disk axes and the hub do not coincide. For sports driving lovers, I will note the size of the stock discs Honda VI-RS and EC4 - 195/55 R15 6J ET45 4X100.

Disc designs

• 4x100 ET38 56.1 mm.

Disc and tire designations

• 185/60 / R14 - stock (factory) rubber values.
• 205/45 / R16 - Rubber values \u200b\u200bas an example.

• 205 - Width in millimeters.
• 45 - Thickness in percent ratio to width.
• 14 - diameter in inches.
• R is the designation of the radial cross section of the cord on the tire, there is also a diagonal D section.

For comfortable ride russian roads - 45 This is not enough. For me, it is better to take 55. Wary than 205 makes no sense to take, on turns under the bias, the wheel touches the army. He himself chose summer tires Yokohama s.Drive 195/55/15.

Some discs (for example, Phobos - VSMPO company) must be purchased internal spacers, axis adapters from 56 to 72mm. Usually they are plastic - imagine. It is advisable to turn to the turner to make metal. Sizes of spacer 56-72 are in articles.

Tire pressure Honda Civic

These parameters are also on the stickers of the sidebar of the driver's door. I will give her copy:

Taken from the operational book.

Disks

• 13x5 J.
• * 14x5 j.
• 14x5 1/2 JJ.
• 15x5 1/2 JJ.
• 15x6 JJ.

Size of permissible tires Civic

• 165/80 R13 82S.
• 175/70 R13 82h
• 175/65 R14 82h
• 185/60 R14 82h
• * 185/6 5R14 85S
• 185/65 R14 86h
• 185/70 R13 86h
• 195/55 R15 84V.

* - not attended in Russian documentation.

Turn or not clutch discs

Very relevant question for all seasons. Which wheels can be put on a vegetable Honda Civic EJ9 and EK3. Our break is 4x100, with planting Moz 56.1mm. The perfect departure from ET38 to ET45, if the departure is less than the arc. Collecting small statistics now everyone can choose himself.
The mark of XX means that the parameter unfortunately is not known. If you can add, you will help many decide on the choice:

• 6.0 ET38 R14 - OK!
• 6.5 ET38 R14 205/60 - OK!
• 6.5 ET38 R15 195/50 - OK!
• 6.5 ET33 R15 195/55 - Trete Lunohod
• 6.5 ET38 R15 195/50 - OK!
• 6.5 ET38 R15 205/50 - OK!
• 6.5 ET45 R15 195/55 - Optimal Option
• 6.5 Et45 R15 185/60 Nothing hurts.
• 6.5 ET45 R15 195/50 Springs -40 OK!
• 205/45 R16 (Stoke suspension, do not work)
• 205/50 R16 (Stoke suspension, do not work)
• 205/40 R17 (Stoke suspension, do not work)
• 7.0 ET25 R1X - Lunohod with 20mm outward
• 7.0 ET37 R1X - rear collapse -2, gap Arch-Wheel 2mm
• 7.0 ET42 R16 - OK!
• 7.5 Etxx R17 205/40 - Landing -30
• 7.5 Etxx R16 205/50 - OK!

Check the tires regularly for damage. Check the tire pressure every two weeks or at least once a month. Do not forget to check the pressure in the spare tire.

ATTENTION: When transporting heavy loads, the pressure in the rear tires should be increased by approximately 0.5 bar.

Note:

1. The lower the height of the tread, the greater the risk of tire sliding. The efficiency of tires for movement in the snow is significantly lost if the protector is wears up to a height less than 4 mm.
2. Incorrect tire pressure can reduce its service life, and managing your car becomes less secure.
3. Reduced pressure leads to excessive wear Tires, increasing the likelihood of puncture of superheated tires, bad controllability and increasing fuel consumption.
4. If the tire pressure is very low, then it may be deformed the wheel or the tire separation occurred.
5. High pressure in the bus leads to a violation of the comfort, car handling challenges and increased wear of the central tire tread pathway.

Pressure checks only when the tires are cold. If the car is in the parking lot at least three hours, then the testimony of the pressure gauge will be faithful.

Attention:

1) Always use the pressure gauge. Appearance Tires can mislead.

2) Do not forget to install the tire valve cap, as dirt and moisture can get into the valve, which can lead to air leakage.

Replacing tires.

1. When replacing tires, use only tires of the same sizes and designs with originally installed, and with the same or greater load capacity. Using the tire of any other sizes or type can seriously affect controllability, comfort, accuracy of speedometer / odometer readings, clearance, distance between the body and tire or anti-slip chain.
2. It is recommended to change all four tires or at least both front or rear tires at the same time.
3. After repairing the tire, the wheel must be balanced.
4. Each 5 thousand kilometers, change the tires on the scheme specified in the figure.
5. Pay attention to the tread pattern. On tires with directional pattern of the tread, the arrow in the direction of rotation is applied to the side part and the "Rotation" may also be present.

Features of the operation of aluminum disks.

Attention: In order to avoid damage to the layer of protective varnish, do not allow employees of tire workshops to clean the outer surface of the disk with a metal brush and when replacing adhesive balancing loads to remove them with a screwdriver.

1. If the permutation is performed, replacing or repairing the wheels, then after the first 1600 km. Check the reliability of the fastening of nuts.
2. Use wheel mount nuts and Honda key specifically designed for aluminum disks.
3. When balancing the wheels, use special weights for aluminum disks, as well as a plastic or rubber hammer.
4. Periodically check aluminum discs in the absence of damage (cracks and chips.) If there are damages, replace the wheel immediately.
5. When replacing tires with a directional tread pattern, check the correctness of their installation.

Landing size of discs on Civic Ferio 2001-2005 in. (Disks)

1. Replace the wheels of wheels should be given due attention. Make sure that the discs are installed with the same load capacity, diameter, rim and departure width.

2. Incorrect disk selection and tires may not affect manageability, wheel life and bearing, cooling brake mechanism, speedometer / odometer reading accuracy, magnitude brake path, direction of headlights, bumper height, ground clearance and the distance between the bus and the body.

Depending on the type of tires, the following discs are sets listed in the "Tire sizes matching the wheels parameters". For example, a possible marking is given:

6JJX14H4 - ET45 - PCD100 - DIA56

In the disco wheel marking the first digit " 6 "Indicates the width of the rim" N."Pronounced either in millimeters or in inches. Letters in" JJ."Indicate the shape of the rim. Subsequent number" 16 "Indicates the boarding diameter of the wheel disk" D."In inches, which should correspond to the seating diameter of the tire installed. Number" 45 "After the letters" ET."Indicates a disk departure ( ET. ) in mm. Also in marking are the following notation: " H4."Means the presence of 4-period holes for fastening bolts or studs, numbers after designation" Dia"The diameter of the central hole," PCD."The diameter of the location of the holes for fastening bolts or hairpins.

Table. Matching tire sizes with wheel disk parameters on car Honda. Civic Ferio.

	Disk	Departure, mm.	PCD.	Dia

Allowable tires and discs "Honda".

TO manager	Disk Type Tire	Departure Em in mm.					PCD.	Dia
	205/45R17
	215/40R18.

* - After installing the front wheels, be sure to check that the suspension and body elements do not hurt in the extreme positions;