How to drain gasoline from a tank foreign car or domestic car? How to drain gasoline from the car's tank, a few useful tips how to merge gasoline from a tank foreign car.
Probably there is not a single driver who did not fall into such a nuisance as the need to drain the car. It is very important to perform this action according to the safety regulations, as well as know which of the existing methods is suitable for your car.
When it becomes necessary to merge fuel from the tank
Drivers are interested in how to merge gasoline from the tank foreign cars and auto domestic production, as well as when necessary. Drain may need:
Regardless of the brand of the car, each fuel tank is equipped with a filler neck, which is closed with a screw cover. Some modern cars have a lock on this lid.
The neck is in the rear, with the left or on the right side. Between it and the tank placed connecting their part - fuel line. It has a view of a different diameter tube, which depends on the brand and car design. New vehicles are characterized by the presence of pumps intended for fuel supply to the power unit. Also in these cars, the gasoline level is controlled by a special sensor, whose readings can be seen. It is worth noting that the electrical wires in these pumps do not lead to an explosion.
The presence of a special ventilation system allows you to maintain the optimal level of pressure. In addition, the tank is equipped with a gravitational valve, whose task is to prevent gasoline spill while tipping the machine.
Methods
Important! Working with fuel during plum is only necessary in the open area. It is necessary in order not to imagine gasoline couples, which are toxic, which in turn is great harm to human health.
Most often, drivers are interested, as properly through the hose to merge gasoline, since this method is the most common. The simplified version of the method implies the use of the hose or tube of the required length. So, one end must be omitted in the benzobac, which is carried out through the neck for the bay. And the second end is taken into the mouth, tightly clasped her lips, then the air is drawn and immediately lowered in a precipitation to the container. It should be noted that the end of the pipe should be not at the same level with a tank, but below.
When you need to complete the actions, you just need to raise the hose above the tank level and remove it from the neck.
Despite the ease of the procedure, it is dangerous, since in the absence of skills you can swallow fuel. But it can be avoided if using a special hose with rubber pear. In this case, it is necessary to squeeze and open the fixture.
Some experienced drivers argue that a medical pear is also suitable for this. It must be the desired diameter. There is a nuance here. So, in the process of the drain, when the fuel goes on the hose, it is necessary to remove the pear from the tip and quickly send the end of the hose to the container.
When the possibility of using pear is absent, as well as the desire to taste gasoline, you can independently make a safe device. For this, tissue cord is taken, it is possible to use a rope that can easily pass inside the hose. At one end of the cord, a couple of nodes are tied, they will serve as pistons, they are also wetted with water.
When the cord is in the pipe, it is immersed by a knotted end to the tank, and the second is lowered down into the tank. Next, the cord smoothly, without applying sharp movements, pull. Thus, the piston must reach the opposite side, after which the cord is pulled and falls into the container.
Such methods are suitable only for old cars, new models are characterized by a thin, winding fuel industry. And when there is a grid in the gas tank, with the help of the hose, the fuel will not work. But do not be upset, as there are other ways. Experts advise to resort to the following methods:
- Most modern cars are equipped with a special drain hole from the bottom of the tank. It helps to completely drain fuel. The driver's task includes only his search, after which it is necessary to unscrew its plug and substitute the reservoir where gasoline will merge. This method is considered simple, but sometimes crawling under the vehicle is uncomfortable, and not all cars have such holes.
- To make a drain of fuel, it is enough to carry out several outstanding steps:
- and open the hood;
- perform disconnection of the fuel hose in the place where it connects with the engine;
- the end of the hose is placed in a reservoir designed for drain;
- run the ignition, while the engine must not be established. At this time, the fuel pump should be engaged for a couple of seconds and start swing fuel. Such actions (inclusion and shutdown) should be repeated several times, until the required volume of gasoline is drained.
Applying the last method, the drivers should know that all the fuel is impossible to drain this method. This will prevent the failure of the gas station as well. They will be prompted that the fuel in the tank is over, bubbles in gasoline merge, which indicate the suction of the air by the pump. Then you need to immediately turn off the ignition.
Precautions
During the drain, you should remember the safety technique. So, you need to do actions away from open fire, do not smoke near, as one spark is enough to have an irreparable. This is associated with a flammable feature of the product.
If you have applied the Dedovsky method - pumping up with the help of the hose and the fuel was discharged, you need to quickly rinse your mouth with the help of ordinary water. The hose is forbidden to sharply pull, for its light removal, it should be slightly pressing a wooden bar valve. After the procedure, the tank must be tightly twisted with a lid.
As for the choice of the tank. Experts advise preference to metal tank. The fact is that plastic tanks can provoke sparks due to static voltage of this material. It was this reason that created a rule on vacation of fuel from gas stations only in a metal tank.
Often, drivers face a situation at which it urgently needs to drain fuel from the gas tank. This is necessary, for example, when unsuitable fuel or poor-quality, or gasoline needs to merge to repair the fuel system of the vehicle. If the fuel plums from the classical domestic model does not represent special difficulties, everything is much more difficult with foreign cars.
This is due to the fact that on the filling neck of the gas tank install a special grid used as a filter and protection against those who love a light job so that it is impossible to lower the hose into the fuel tank, as on the domestic classics.
Initially, I would like to give a warning that the information described below is intended for drivers who need to produce urgent plums of gasoline from the fuel tank of its car.
But not for those who want to earn easy money, devastating the gas tanks of other people's cars. No need to forget that such actions are a crime and are punished on Russian legislation. In this regard, consider ways to drain gasoline from modern cars, especially foreign cars.
Methods for draining gasoline from gas tank with a protective net
If there is a grid inside the car's fuel tank, and the gasoline with a hose does not work, do not be desirable, as there are other ways to implement this procedure.
Usually on most modern machines, at the bottom of the fuel tank there is a special hole for draining fuel through which gasoline from the tank can be drained. You only need to detect this hole, substitute dishes under it and open. This method is characterized by simple and does not require any intervention in the machine device.
However, it is necessary to remember that such holes are not every machine, and it is not always convenient to crawl under the car, in the search for the drain hole.
Therefore, there is another option to plush gasoline from the fuel tank of foreign cars. To do this, you need to open the hood of the machine and, stopping the motor, disconnect the fuel hose in the place, which is located after the fuel pump. The hose must be placed in the tank and ask for an assistant, check the ignition key. The machine does not start, but the fastest fuel pumping along the hose will begin with the fuel pump.
This procedure will have to be performed several times, as you need to stop the pump for its cooling. When using this method, it is better not to merge all the fuel so that the fuel system does not happen. It is also necessary to remember that the packaging of gasoline from the gas tank of foreign cars should occur in the open space, to eliminate the possibility of poisoning with fuel vapor, harmful to humans.
Sometimes car enthusiasts face an urgent need for a small amount of gasoline (for example, for household purposes - wash the tassel, covered with paint). Of course, you can go with some small capacity for the nearest gas station and purchase 1 liter of gasoline.
But often to go far, gasoline does not need a lot, and the car is it, it is standing in the garage. It is much easier to borrow a little fuel from the Tank of the Iron Horse. The owners of "Zhiguli" do it very simply: the hose into the tank - and ready.
What about those who have a modern VAZ or a foreign car with mesh in the neck of the tank for fuel? In this article we will talk about 2 methods of draining fuel from gas tanks of such cars.
How to drain gasoline from the gas tank foreign cars
Method number 1.
Most modern machines are equipped with a special drain hole with a plug located at the bottom of the gas tank.
It is not always easy to find it, so it's better to turn to the manual for the operation of the car or the literature on its repair. Then everything is very simple - substitute a pre-prepared container, unscrew the plug and drain gasoline.
In some cases, you may not be lucky, and the fuel tank of the car will be without a drain hole. In this case, try the method number 2.
Method number 2.
The procedure for action is:
1) Make sure the engine does not work, and open the hood. 2) Find a hose from the fuel pump, and disconnect it in a place where it is suitable for the motor. 3) Place the free end of the hose in the container (plastic bottle, for example).
4) Turn the ignition, but in no case do not run the motor! The fuel pump with the ignition is turned on rolls a little fuel that falls into the container. 5) Include-turn off the ignition until the necessary number of gasoline is solved.
6) After that, connect the hose back.
It should be noted that it is not recommended to use this method without extreme need (especially if the benzobac is almost empty), since there is a risk of breaking the fuel pump and / or bring the fuel system.
In conclusion, it will not be superfluous to remind of fire safety. Remember, gasoline is a flammable liquid, so do not smoke until you drain it, remove the potential sources of open fire and do not spend this procedure in a closed room (only in an open place!). Otherwise, choose poisonous fuels.
How to drain gasoline from the tank
Quite often, vehicle owners fall into a situation when it urgently needs to quickly and qualitatively drain gasoline from the fuel system of their car.
And here there is a fairly common problem: if the fuel is not difficult from the domestic car at all difficult, then in the case of foreign cars everything is much more complicated, because in the neck of the gas tank in most modern cars there is a mesh that acts as a filter. She is just not allowed to merge fuel.
Based on this, we offer you several ways with which you can quickly and efficiently extract gasoline from the tank of your "four-wheeled friend".
How to drain gasoline directly from the gas tank?
The simplest and most quick way to drain fuel from cars, in which the filtering mesh onto the gas tank is installed, is drained through a special drain hole.
As a rule, most of the complete sets of any car have a certain neck on the bottom of the gas tank, which is designed to drain fuel. So you only need to detect it, open and substitute the canister either a bottle, which actually will be removed fuel. This method, as you understand, is quite simple and, most importantly, which does not require any expenses and any interference in the fuel system of the vehicle.
How to drain gasoline from the injector?
Also merge fuel directly from the tank car using the fuel hose. To extract fuel using this method, you will need to look under the hood of your car and carefully pull the hose on the one hand - it is located near the gas station. Then turn on the ignition and substitute any container under the hose. This car does not start, but the fuel pump will immediately begin to push the fuel.
Helpful advice
However, if you remove the fuel with this method, do not merge all fuel, because as soon as the pressure of the fused fuel will weaken, the air will fall into the fuel system and it will be delivered. In this case, you will have to pump it with a manual pump until all the air is deleted.
Thus, you see that it is not so difficult to merge fuel from a foreign car. It is only necessary to carry out the dramatic and not forget about the safety technique, and in this case you will definitely work out.
Below you can view the video on how to drain gasoline from the injection car.
How to drain gasoline from car tank | Self-speaking
Sometimes there is such a situation when it urgently needs to merge gasoline from the tank.
For example, you are not poured by that gasoline, or gasoline is very poor quality, or gasoline needs to be merged in order to repair the fuel system of the car.
If the gasoline from the domestic classics does not represent much difficulty, then with foreign cars much more complicated, as a special grid is installed in the filter, which serves as a filter and protection against fans of light profit so that they cannot omit the hose to the tank, like this Made on classic. Therefore, we suggest familiarizing yourself with ways, how to merge gasoline with modern cars.
Initially, I would like to note that the article is intended for those who urgently need to drain gasoline from the tank of its own car, and not for those who wish to make a lot of money, devastating the tanks of other people's cars. Remember that such activities refers to the number of crimes and strictly punishable by law.
Ways how to drain gasoline
So, if the grid is installed in the gas tank of your car, and it will not be able to drain gasoline with a hose, do not despair, because there are some more methods as you can do this procedure.
As a rule, a special drain hole is installed on many modern cars at the bottom of the gas tank, allowing you to get rid of gasoline in the tank. It is enough just to find this hole, substitute the container and open it.
The method is quite simple and does not require serious interference in the car system.
But such holes are not available on all cars, and it is not always convenient to crawl under the car, in search of a drain neck. Therefore, we bring to your attention another way, how to drain gasoline from the tank foreign cars.
It is necessary to open the hood of the car and on the plugged engine to disconnect the fuel hose in the place located after the fuel pump. Put the hose into the container and ask the assistant to check the ignition key.
The car does not start, but the activated fuel pump will quickly start pumping the fuel through the released hose. It is necessary to exercise this one several times, allowing the pump to cool.
In such a way, it is better not to merge absolutely all gasoline, so as not to bring the fuel system.
As a warning, we note that it is necessary to drain gasoline from the tank only in the open space in order to eliminate the possibility of poisoning with fuels, which are very harmful to human health.
Source: https://autoprivat.ru/remont_avto/kak_slit_benzin_iz_baka_inomarki.html
How to drain gasoline from cars
Probably everyone at least once arose such a situation when all gasoline should be merged from the gas tank. For example, when you poured low-quality gasoline or need to merge to repair the fuel system.
In any case, if with domestic cars to drain gasoline is not so difficult, then with foreign cars you will have to tinker.
In the plug-in neck, such cars, as a rule, mounted a special grid, filtering fuel and protecting from easy profitable, so that no one can insert the hose into the tank to extend gasoline. Therefore, it is very important to familiarize yourself with the methods of draining gasoline from modern cars - it is very important.
Immediately it is worth noting that these tips are intended for those who want merge gasoline From your personal car, not for those who think as easy to earn. Please note that theft of gasoline is a crime, so it is punishable by law.
Merge gasoline from a gas tank protected by a grid
So, if your car is mounted in the gas tank, then merge gasoline With the help of the hose simply fail. But there are always other ways to help cope with such a task. You need to check immediately: Maybe your car is equipped with a special drain hole that allows you to free yourself from gasoline in the tank. If there is a drain hole, then everything is extremely simple: install the container and we merge gasoline.
Merge gasoline from a car that does not have a drain hole
Drain holes are not on all cars, and it is not always convenient to lie under the car in his search. Therefore, you can try the following method. Open the hood and from the muffled engine, disconnect the fuel hose where it comes out of the fuel pump. Hose put in a container and ask the assistant to turn the ignition.
In the life of the motorist, situations occur when some kind of gasoline is needed to merge from the gas tank of its own car for use in economic purposes (in a motor-block, lawn mower, leafwood) or when trying to assist another driver left in the way without gasoline. This article is intended for assistance in such situations. The use of this information is not allowed in illegal!
There are several ways drain gasoline from the tankcar : Fill the hose through the bay neck, pull out the fuel line or through a plug cork. Each of them has advantages and limitations associated with the design of a particular car. For example, for Daewoo Lanos, Chevrolet Niva and Vazovskaya "Classics" are suitable for the same techniques that are not applicable to Ford Mondeo. Some methods will be able to implement only under workshop conditions, others - easily driven on the road. To choose the best option, you need to take into account how much gasoline is required, to which section of the fuel line is easier to provide access and which devices are at hand.
Required tools and devices
In order to carefully produce gasoline from the tank of the car you will need:
- Liquid packaging.
- Transfusion tube.
- Screwdriver for removing clamps, keys (optional).
- Manual or electric pump (optional).
Important! Store gasoline in an open container is impossible. In the air, fuel is actively evaporated, which can provoke fire or poisoning with long-term inhalation of vapors. If the canister trim, PET bottles, other remedies were used to drain the fuel, it is necessary to pour it into hermetic container as quickly as possible. Smoking or meal during work with gasoline - is prohibited by safety technique!
What to overflow fuel
For draining fuel, a transparent hose with a diameter of 6 to 12 mm is needed; two to three meters long. PVC tubes with a wall thickness of 1-2 mm are suitable, which are sold in the "All for repair" (are used to remove condensate from domestic air conditioners), segments "Hydroorrow", as a last resort - a medical dropper.
Transparent walls - an optional requirement (you can use the rubber "oxygen" hose, a car pump tube, etc.); However, among the rubber products often come across non-fuel-resistant, softening from contact with fuel, and PVC, PET and similar materials to it are inert. Passing gasoline through a transparent sleeve, it is convenient to control its quality - in time to notice contamination, rust, or air bubbles when the liquid is about to end.
Than pumping gasoline
Devices helping to simplify work:
- Sprintsovka from the pharmacy. It you can create an initial vacuum in the hose.
- Pump "Pear", he "membrane". Helps "Run" pumping gasoline.
- Household pumps. Low-power devices on batteries from the "store on the sofa".
- The pumping pump pump from the VAZ 2101 (07, 08, 21), GAZ 2410 (3302) Daewoo Lanos, Sens (or any other, having similar parameters), planted on the hose and beacted from the battery 12V.
The last option shows the greatest efficiency (the performance of the device is 10 ml per second).
Where in the car you can merge gasoline
This material is intended for the legal owner of the car, and not idle lovers to get used to other people's gasoline, so only the principle of humane intervention in the motor supply system will be described here. To find out what looks like and where a specific node is located, the driver is enough to look into the manual of the machine (which is desirable to always carry with you).
Scheme of the fuel system of the gasoline engine
Technically, there are several "access points" to a fuel in a car:
- balanced opening of the gas tank;
- fuel supply fuel lines;
- "Furniture" fitting;
- drain plug in the bottom of the tank;
- migiston pressure regulator in the ramp.
The car's gas tank is located under the rear seat or under the floor of the luggage compartment. On most modern cars with a distributed fuel injection, the fuel pump is installed directly in the tank. It supplies pressure to the highway leading to the fuel ramp and nozzles through the pressure regulator. The second branch leads the surplus of gasoline from the ramp back to the tank.
Pumping gasoline by regular fuel pump
Using staff, it is possible to produce gasoline from the car with minimal time and strength. For example, the performance of Ford Focus 2 (1.8) gas station is about 85 liters per hour. With a volume of gas tank in 55 liters, even with full refueling, the operation will take 30-40 minutes.
Caution! Before carrying out work on the depressurization of the fuel line in the procession space, it is necessary to wait for the cooling of the motor to avoid gasoline entering the hot exhaust manifold and fire!
If the car owner of the "injection" car does not need to "dry" the fuel tank, and it is necessary to simply produce a certain amount of gasoline for degreasing parts, you can use the diagnostic fitting of the fuel pressure regulator. Find the regulator is easy - it is on top of the fuel ramp or in her face. In the opposite end - there is a diagnostic connector.
Sequence of work:
- Disconnect the pressure regulator in the ramp.
- Wear on the fitting the tube and take it into an empty container.
- Turn on the ignition, not a winding engine.
- If necessary - repeat.
For a few seconds, the pump will have to drive out into the substituted bottle of about a hundred milliliters of gasoline.
If you set the jumper between the contacts of the fuse relay (located in the overall fuse box, the Fuel Pump is denoted), you can "get around" automatic shutdown of the fuel pump in 2-3 seconds. After starting on a non-working engine. It is recommended to merge fuel not completely at once, but by portions of several liters and constantly monitor the fluid level, preventing the operation of the pump "on dry".
Attention! The device will earn immediately as soon as the contacts are closed, even when the ignition is turned off! First of all, you need to prepare sufficient container and securely fix the tube in it.
How to drain gasoline from the tank through the "return"
In order not to risk a fuel pump, you can use the backlog of the reverse plum, which drops the excess fuel into the tank. This method is suitable for most foreign cars with a plastic tank. Minus - to get to him, you have to disassemble the back of the cabin.
Sequence of work:
- Remove the back seat.
- Jumping fasteners, remove the gas tank lid.
- Remove the "return" tube (which is closer to the connector) by pressing the plastic clamp or pushing the latch.
- Substitute a container under it.
- Turn the engine. Control the filling of the container.
The method is suitable for Skoda Rapid, Renault Logan, Mitsubishi Lancer.
How to remove all gasoline from the tank
Machines, produced before the early 2000s, were mainly completed with a metal stamped fuel tank. To empty it, you need to turn the plug plug (nut in the center of the bottom of the reservoir). Drain one of the tanks (or both) by the UAZ Patriot car, you can without the "pit" or lift - clearance allows it. For repair of the Chevrolet Tank Niva, VAZ 2121, VAZ 2110; Moskvich 412-2141 and other cars are better to take advantage of the observation pit.
It should be remembered! As soon as the drain plug is boiled, the fuel immediately sticks with it! No need to try to look into the drain hole so as not to get injury!
Drain gasoline from the tank of a more modern foreign car through a similar plug - it will not be possible: automakers switched to whole plastic components, which have only two holes - filling and to install the filter (fuel pump).
If you need to remove the tank, and the gasoline has nothing to refuse - the fuel pump refused - it remains to be fully removed, together with the filter grid, and after - through the hole in the lid, pump the contents using the hose. So, on Ford Mondeo (1.6) To dismantle the benzobak, you will have to remove the filler tube from it and drop fuel through the released inlet.
Working with fuel, it is necessary to use the containers and properly dispose of the waste of petroleum products, not allowing them to enter the environment.
Fuel plums with a simple hose: Dedovsky way
The old method, which saved the owners of most Soviet cars remaining on the highway with a "dry" tank, is convenient because it can be used anywhere: a sufficiently rubber "intestine", tanks for gasoline and patience. This option will be able to use the hosts of machines that are not equipped with partitions in the neck of the tank. You can get gasoline from the Baka Lada Priory (early generation) in this way, but with a viburnum and grant this method, most likely, will not work - the tank is very low located, and its neck is very curved.
To facilitate the process of pumping, there are several devices:
- upgraded tube;
- mechanical pump "Pear";
- serial electric household pump;
- homemade Material Pump Base.
The modernization of the tube is fastening at one end of its end of the metal nut or fitting, which will be easier to descend into the tank under its weight, despite the complex shape of the filling channel. The second end is tightly done through the plug from the plastic bottle (3.0-10 l), the joint is sealed (thermoclaim, sealant, chewing, etc.). Nearby in the same way, the segment of the same tube length is 15-20 cm. Now, if you wear a plug on the bottle and draw the air from the cutting tube, the cutting in the tank will leak fuel into it, and not in the body.
The easiest way
If there is nothing at hand except the hose:
- Lower one end of the tube through the bayful neck just below the fuel level by locking its position.
- Substitute the tank for the drain of gasoline, placing it as low as possible.
- Pull the air from the tube (as a drink through the straw) to the characteristic feeling of "feedback", then sharply lower its edge into the container.
- If the initial impact was not enough to repeat before the formation of a stable stream.
Complete the selection of fuel you need to pull out the "top" end of the tube from the tank, after which it is possible to spend the gasoline completely - then it will be possible to avoid splashes, stains on clothes and the bodies.
Attention! When trying to create a mouth, the initial vacuum in the hose, a number of gasoline or its vapor will necessarily get into the body! With random swallowing of fuel and lubricants - it is recommended to rinse the stomach as quickly as possible. To avoid the effects of poisoning, you need to take a sorbent or fermented food. It is ultimately not recommended to "wash off" the taste of gasoline alcoholic products, "interrupt" garlic or other sharply smelling products - it will only aggravate the situation.
More on how to protect against the drain of gasoline
There are many reasons why you may need to merge fuel from the tank ,. The most frequent reason is which you poured on the gas station. In the old days most often bad fuel meant that it contains solid outsided particles or water. But, this still was rarely found, in case the driver referred to the brought out of major settlements, where usually unscrupulous owners of the gas stations tried to sell poor-quality fuel coming from illegal factories in Chechnya. Today, such a disgusting fuel you are unlikely to meet in our country. But this does not mean that you will never need to merge fuel from the tank.
See also:
If 10-20 years ago, bad fuels were more disturbed by the owners of old cars, since they were most susceptible to breakage due to poor-quality fuels, today the problem of poor-quality fuel can concern everyone without exception of vehicle owners.
Do you ask, don't they sell low-quality fuel today? Answering the question, our answer will not be unequivocal. The fact is that the situation with the quality of fuel at refueling today is of course much better than 10 years ago. Over the past decade, the number of network gas stations in our country has increased several times. Also appeared branded fuel fuels of oil companies, as well as our country smoothly switched to fuel corresponding to the modern ecological standard Euro-4 and Euro-5. Therefore, the number of counterfeit gasoline and diesel fuel on the fuel market has significantly decreased. Nevertheless, in Russia there are still unfair owners of gas stations that sell poor-quality fuel.
But this does not mean that the small fuel company fuel is worse than in a large network. The problem is actually in the other. The fact is that modern fuel grades contain a huge number of chemical elements, as a result of new distillation technologies and, which are added to the fuel at the oil plant. All this is necessary, in order for the fuel to correspond to the European environmental standard.
But few know that such fuel has like any product shelf life. The fact is that after the release of gasoline and diesel fuel, the chemical stability of additives and various additives begins to disintegrate with the time as a result of natural chemical reactions. As a result, such fuel, if it falls into the fuel system of the machine, can damage it.
But today it is not about it. We simply gave you to understand that, refueling on the network refueling, you are not 100 percent of the fact that the tank of the car will not fall low-quality fuel. After all, at the time of refueling, you will not be able to find out how much this fuel was stored at the oil plant, in fuel truck, etc.
Now let's go back to the main topic of our article. Let's find out how to drain bad fuel from the tank.
When it comes to how to merge gasoline or diesel from the fuel tank, many drivers in front of the eyes arises not a pleasant picture. They imagine that to drain the fuel you need to take the hose and one end to insert into the fuel tank. On the other side of the hose, it is necessary to create pressure using the mouth, breathing in the hose. As a result, the fuel from the tank will begin to come out under the pressure created.
It's important to know:
Usually, while the Dedovsky Plum method, the main thing is to have time to substitute the container at the moment when the fuel starts to come from the hose, as well as to pull the hose from the mouth. Yes, this method really works, but let's not focus on this method of 20 centuries. It is dirty and not modern. In the yard of the 21st century after all. Especially since this is an ancient fuel drain method is not suitable for many modern cars, as well as not safe.
We recommend using for draining fuel with a special hand pump for pumping out combustible liquids, such as gasoline or Diz. fuel. You can buy this pump in the auto shop. Please note that not all manual pumps that are on sale in the store are suitable for pumping out fuel. Therefore, before purchasing a pump, make sure that it has tolerance for pumping fuel fluids.
We also advise not to acquire cheap pumps, as a rule, they have a very small volume, which is very uncomfortable. So it is better to overpare, but buy a normal manual fuel pump, which in addition to the pump will include all kinds of hoses and adapters.
Before starting fuel pumping, make sure that you all connected correctly. To drain you will need fuel capacity (canister, bucket, etc.).
Attention! If your fuel tank is complete, you will need several tanks for fuel pumping.
Before you begin, be sure to read the instructions for the pump. Collect the pump according to the applied instructions. Then insert the hose into the car's fuel neck. Now take the other end of the hose of the hose from the pump and insert it into the canister.
There are several ways to drain gasoline from the tank, one of them are universal, others are suitable only for specific car brands. We will analyze the most effective of them on the example of domestic cars and foreign cars.
But it is important to understand what it is necessary to do it only into a metal (aluminum) container. Plastic can cause a spark and fire so it is used although it is convenient, but dangerous.
It is also prohibited when the gasoline is drained the use of open fire, knocking metal on metal, so as not to cause a spark, in some cases carry out work on the hot engine.
Domestic cars
VAZ 2110/2112 / 2114/16 injector valves
Below, the listed methods are also suitable for those cars, where the protective grid is in the fuel neck.
Sleep gasoline is needed on a cold engine.
Would need:
Algorithm of actions:
The first one, just disconnect the hose ahead near the engine:
At one time, about 100 - 150 ml of gasoline. Next, turn off the ignition and turn on again.
Suitable for injector cars VAZ 2110, 2112, 2114, Lada Grant. Also take the hose and container.
Methods 2 and 3 are not suitable for a situation when you need to completely drain gasoline. Frequently on and off the ignition will quickly plant ankb, and if you have a car, that is, it is highly likely that the pump will work idle and burn.
In Lada Grant, too, we also find a fitting for measuring pressure, it is located there wherever VAZ 2110. All operations are also done.
As an option, you can apply the following method.
The hose is connected to the methods already described above or directly to the fuel ramp.
We find the fuel pump relay and closer contacts. At 2112, 2111, 2110, the relay is at the bottom of the driver's right.
Turn on the ignition. The pump will work continuously. But it is important to know how much gasoline is in the tank to control the drain process and prevent the combustion of the pump. Air intake with gasoline is a signal that ignition needs to be turned off.
This is not a tricky way to drain gasoline on the injectors of domestic cars.
VAZ classic (carburetor), old foreign cars
Option 1.
As a rule, there is no grid in such cars in the neck, so it is enough to drain gasoline from the tank to have a special hose with a pear for pumping fuel.
Lower one end of the hose in the benzobac, the second in the canister and start to download. Usually 5-10 pitching gasoline begins to flow.
Please note, on the pest itself there is an arrow showing the direction of fuel movement.
Option 2.
Use of an ordinary hose and your lungs. It is important not to impass the vapor of gasoline and do not swallow the fuel liquid.
To prevent this, use transparent not too thick (4-6 mm) and not very long nozzle (from 2 to 3 meters no more). Cutting one side at an angle of 70 degrees, so it will be better to merge gasoline.
Lower the hose to the tank in such a way that he concerned his bottom. Then, if not cut, lift it to a couple of centimeters. This is done in order not to overlap the hose hole at the bottom of the tank.
The perfect option when the hose falls to the bottom of the tank by a semi-ring, that you will achieve the maximum fuel reckoning. To do this, secure a small cargo near the end. Where the fuel line has several bends option with a load does not pass.
Start to make a sample, while your mouth must be lower than the represented gas link in the tank.
The higher the fuel will climb through the tube, the harder will create a vacuum. If the hose is transparent, then the process will be visually visible.
As total - gasoline will begin to merge, the main thing is to redirect it from the mouth to the canister.
What an error was allowed on video, write in the comments.
Option 3, 4.
For those who are afraid of gasoline tightening, you can collect the following designs.
Take 1.5 / 2.0 liter container and in its lid do two holes. Insert two nozzles and place where they enter the epoxy resin. Screw the lid.
The end of the hose through which the air will be asset should be in the bottle higher than the one that goes into the tank. The scheme is visible.
We begin to suck the air, while we do not inhale the pairs of gasoline and exclude the opportunity to try the fuel fluid to taste.
Or in order to drain gasoline from the tank using homemade pump. To do this, take the same pipe as in the method described above (can be slightly thicker) and the rope is 10% longer.
Skip the rope through the hose and at one end, the knot, so that it passes with the effort through the hole.
Moisten the knot in the water and tighten it into the hose. Fishing the knot completely blocks the passage. Lower the end of the hose with the knot into the tank and start stretching the rope. The created vacuum will pull in gasoline, which will eventually begin to merge.
Option 4.
Use of a vacuum cleaner. To do this, you will need:
- the vacuum cleaner itself;
- tank with a dense lid;
- two rubber tubes.
Collect the design:
- in the capacitance lid, we make two holes in which insert two hose tightly. Pour the epoxy resin place so that the air does not pass.
- the first pipe through the seal (or in another way) is connected to the vacuum cleaner, the second is lowered into the tank.
Turn on the vacuum cleaner on suction. Thanks to the created discharge into the container, gasoline will be merged.
Option 5.
Trite simple. Find out whether it is constructive a drain plug in the gas tank of your car.
If yes, then beat the machine on the pit (overpass) or lift the lift. Unscrew the cork and drain gasoline.
By the way, if there is no such cork, it can be installed on your own.
The disadvantage of this method is obvious, it eliminates the fastest fuel on the road, for example, if you need to assist someone.
UAZ Patriot
On the UAZ Patriot to merge gasoline from the tank the usual "people" way will not work. To do this, you can use the fuel pressure valve. We find it and unscrew the spool with a cap. Picking gasoline is collected in the prepared capacity.
Connect to the valve with a pipe with a diameter of 8 mm.
We find the fuse block, remove the lid and find a gas station relay in it. Remove and install the jumper circuit. It is desirable to insert the fuse by 5-10a in the jumper itself.
Even inserted into the ignition lock, the gasoline key will begin to merge. In 3 minutes, you can merge up to 10 gasoline.
Niva Chevrolet
In Niva Chevrolet, the fuel tank is installed in the body and therefore the drain hole in it is not provided. But the plus is that there is no protective grid in the pipeline of the filler neck and it is relatively smooth. Therefore, for the plum of gasoline in this case, most of the above methods are suitable.
It is important to consider that the tank itself is far from the filler neck, so to capture the fuel pipe should be about 3 meters long and a diameter of 4 to 8 mm.
Also, many car owners to protect against gasoline plum are installed in the filling pipe of the Chevrolet Nivrolet grid from the meat grinder with large holes.
If you installed such a grid, you will have to merge the fuel using a gas station (about it said above).
Lada Kalina, Priora
Fuel tank of Lada Kalina is made of plastic, gasoline plums are not provided. Also, the bay hole itself is located in the center of the tank, and not on the side.
The poet nozzle from the filler neck to this hole is long and has two inflection.
The plus is that there is no protective grid in the bay pipeline. Therefore, not all is lost.
Prepare a canister and a hose with a length of at least 2.5 - 3 meters with a diameter of 1-1.5 cm. So that it freely entered the neck.
Run the hose inside. At first it will go freely and even the first inflection of special difficulties will not cause. Then he will strengthen into the second bend and here you need to start riding it counterclockwise, as if you can read the sewer.
Move the hose make sure that he sank into the tank. Drain gasoline with a pear or creating the discharge of the mouth (the method is described above).
The problem is that the fuel tank on Lada Kalina is too low, and therefore will have to be tilted to the earth itself so that gasoline began to merge. Or drive cars to a pit or aleacade.
Also merge gasoline from Lada Kalina (cross) by connecting to the fuel system through the fuel pressure control valve, we wrote about it higher. Or through the rear seats to get to the fuel pump, how to do it higher.
In the same ways you can drain gasoline and in the lade of the prior.
We use pumps
Technologies do not stand still. To merge gasoline from the tank, you can use ready-made solutions - these are manual and electrical pumps for pumping liquids.
For electrical devices, you will need power in 12V / 24V. They are immersed and not immersed. For passenger cars will suit the second option.
But you need to understand that there are pumps that can be pushed only diesel fuel, water, oil, and gasoline is impossible. Therefore, before purchasing such a device, carefully examine the instructions for it.
But for not everyday use, it is advisable to have hand pumps, they are much cheaper and no less efficient.
Foreign cars
Lada Largus, Renault Logan, Sandero, Duster
We took Lada Largus to foreign cars, it's not by chance that this car was done on the Renault platform, which means that fuel systems are similar, especially with Renault Logan.
The fuel tanks in these cars are located low therefore merge gasoline with the help of the hose does not work, but you can go to another.
Remove the back seat, so you get to the fuel pump. Connect the pumping hose to the output fittings. Next Close the pump relay. The latter will start pumping gasoline.
For example, take Renault Duster. First reset the pressure in the system. To do this, disconnect the electrical connector from the pump and make a car for a few seconds.
Important: Do not allow air to enter the pump.
From Baka Ford
Consider on the example of Ford Focus 2. Dry gasoline through the bay neck here it will not work, the valve, the grid, the fifume bends will not allow it to do.
You can remove the fuel tank, but this time-consuming work is therefore not worth the heater.
The option directly through the fuel pump is attractive, but provided that you have already changed this fuel system element earlier and cut the hole in the bottom under the rear seats, the explanation here. If not, then to engage with a sharp metal to only drain gasoline inexpediently.
The simplest option is to disconnect the tube from the fuel ramp, it is attached to the latch, connect the hose with a diameter of 8 mm and the ignition is plugged into fuel.
But if the tank is complete, and it is 55 liters, and 4 liters merged in a minute, then the whole process will take a lot of time and you can plant ankb. Therefore, we find the relay of the fuel pump and closure on them two contacts (two lower slots). Do not forget to put the capacity of greater volume.
Turn on the ignition and drain gasoline. Be careful, it can flow and without inclusive, immediately when the relay contacts are closed.
Toyota
We will analyze on the example of Toyota Camry 40. To merge gasoline from the car's tank, you can use one of the ways that is described above. List them:
Similarly, you can go on other models of Toyota.
If there is a problem to merge gasoline from the tanks of Skoda Octavia, Lanos, Aveo, Matiz and other cars, then the approach to solving the problem is already known to you. See which options described above suitable for your car and use them.
Write about your ways in the comments. And now let's talk about Daewoo Lanos.
