Oil volume in the VAZ 2109 1.5 engine. How to change engine oil on nine

The engine is the heart of any car. It is important to monitor its health and quality of the oiled oil. With normal operation, the lubricating fluid varies after 10,000 km of the mileage, if the conditions are heavy, then the replacement is carried out more often. For replacement, you need to know what and how much to pour oil into the VAZ 2109 engine.

[Hide]

We carry out a replacement

For impeccable engine operation, it is necessary to regularly monitor the level and condition of the oil, to change it on time. The replacement is usually carried out for the following reasons:

• excess recommended run;
• season change;
• changing the brand of oil;
• heavy operating conditions.

All listed factors affect the frequency of replacement of fuel. In summer, the lubricant must be more viscous than in winter. With long-term operation, the lubricant loses its properties, the additives, particles of chips, which appear during the friction of the engine parts are seen.

Sorry, currently there are no accessible surveys.

How much oil pouring?

How much lithra casting depends on the model of the machine. The volume of filling fluid into the VAZ 2109 engine is usually 3.5 liters. Buying better than 4 liters, the remaining lubricant can be addressed during operation as needed. The amount of the necessary oil is determined using the probe. The level of lubricating fluid should be between maximum and minimum marks. If the level is lower, then it is necessary to add, the main thing is not to exceed the maximum, because It affects the engine badly.

When replacing the oil, the question arises, which is better to fill. The highest quality, but at the same time, the most expensive is synthetic: it has good characteristics and retains them during operation. The semi-synthetic is not so expensive, but its quality is worse. With limited finance and inexpensive car model, you can use mineral.

It is important to note that it is impossible to mix lubricants of different brands. When moving to another brand, you should pour a special flushing before replacing and allow you to work on it a few minutes to the engine. She cleans the system from the old lubricant well.

Instruments

Change the lubricating fluid easily at home. To do this, you need to prepare the following materials and tools:

• a set of keys, including 17;
• capacity for waste liquid;
• canister with new oil;
• funnel;
• new oil filter;
• special key for filter removing or screwdriver;
• clean rags to remove inclination.

Capacity for drain can be used five-liter plastic bottles of water. It is impossible to drain the exhaust lubricant to the ground. For a funnel, a sliced \u200b\u200bplastic bottle is suitable.

To change the lubricant fluid, you need to warm up the engine. To do this, you should start the motor and heat up to the operating temperature, approximately 80 degrees. Next, the car should be installed on a flat horizontal surface: the overpass or the observation pit. With their absence, you can put bricks for the front wheels to lift the car. At the same time you need to put the car on the handbrake, without letting it ride it back. After the preparatory work, it is possible to proceed to the process of replacing the fuel and oil filter.

Replacement process

First of all, you should drain the spent lubricant. If you have protection, it must be removed. Under the pallet, the crankcase is substituted with a waste liquid tank and unscrew the key to 17 a plum plug. It is necessary to act neat, as the lubricant is hot, you can get burns. By reloading the lid, we give a drain of the liquid, as a rule, it takes ten minutes.

When replacing the fuel and lubricants in the VAZ 2109 engine, the oil filter should be swapped. While the lubricant mercy can be replaced. Using a special key, unscrew the filter. In the absence of a key, you can use a flat screwdriver, thoring through the filter housing and using the lever. When the whole liquid stalks, tighten the drain plug on the crankcase.

The new oil filter is poured cooked oil in several stages with a small time interval until it absorbs enough. Usually poured to half. Be sure to lubricate the filter gum and wipe the place where it is screwed. The filter is then installed to the previous place, spinning with his arms, without making great efforts to not damage the gum. Otherwise it is possible to flow with further operation.

For the fill, we unscrew the cover on the engine and with the help of a funnel are poured neatly new oil. First pour 3 liters, waiting when it is completely stalking.

Then gradually fill the rest, controlling the level of fluid using a special probe. To do this, take off the dipstick, wipe it with a clean cloth, insert back. The actual level will be visible on the impurity. Pour oil while its level will not be between the maximum and minimum.

Gulf lubricant, you should run the engine and give it to work in a focus to fill the filter and different channels with lubrication. After starting the motor, the red light lights up - the oil pressure indicator, it should be pulled in 10 seconds. If this does not happen, then the filter is poorly twisted, it should be twisted to eliminate the flow.

Loading the motor, it is necessary to check the lubrication level again and fasten if necessary. Before the end of the work should be checked so that there is no inclination. If there was protection, it is screwed back. This is completed on this process.

Video "Replacing oil in the engine VAZ 2109"

In this video, it is shown how to correctly replace the lubricant in the VAZ 2109 engine.

Domestic cars are best suited for self-service. Simple, but reliable design, good engines and other technical parameters allow you to carry out a number of operations and even repair. One of the most simple tasks is considered to replace the engine fluid. It requires a minimum set of tools, some skills and elementary knowledge about the VAZ device.

Therefore, most of the car owners are performed independently, not attracting specialists with a hundred and without spending money on car service services.

Replacement frequency

So that in good working condition, do not provoke premature wear of parts and loss of the motor life, you need to change the oil in it in it.

If you look into the official instruction manual for the nine, then the manufacturer advises to change the engine oil every 10,000 mileage kilometers. But the actual time or mileage between the replacement is significantly less.

It is important to take into account that "VAZ-2109" is no longer produced for a long time, because the bulk of these cars have a noticeably worn engine. Its resource gradually ends, which is reflected in the state and speed of oil wear.

Also negatively on the physicochemical properties of the engine fluid, the following factors affect:

• climate;
• quality of gasoline;
• the quality of the oily oil;
• driving style;
• terms of Use;
• low road surface quality;
• frequent ride under load (full cabin passengers or trailer), etc.

Negative factors contribute to the loss of beneficial properties of oils. They lose their effectiveness. The liquid does not cope with its tasks, which is why excessive wear of the engine elements occurs. If you do not change it on time, it will lead to overhaul or the need to complete the power unit.

Therefore, experts and experienced motorists operating "VAZ-2109" advise to change the oil about every 5 thousand kilometers, but at least 1 time per year. Will optimally change the fluid twice a year if the motor is worn out

Select Oil

If you repel from the viscosity of the engine fluid, then the vazovts are most often used 10W40, 5W40 and 15W40.

Here you need to consider the weather conditions in which the car is operated. Depending on them, oil can be used with the following viscosity indicators:

Theoretically, you can pour all three types of engine oils. But when used, it is worth considering some important points.

1. Synthetic. These are the most modern and frequently used motor formulations. In general, they are focused on foreign cars and are not so often poured into domestic cars. At the same time, "VAZ-2109" feels good when working on synthetics. Such oil has a high fluidity, resistance to reduced temperatures and perfectly opposes freezing. The only drawback is considered high cost.
2. Mineral. The most affordable engine oils. But they are relevant to use on engines that were significantly worn out. "VAZ-2109" refers to the number of outdated cars, because mineral lubricant is not bad for it. Although it is important to note that mineral compositions are poorly reacting to a low temperature, which is why there are problems with the engine starting. So fill the mineral water with a moderate winter and with an impressive car mileage.
3. Semi-synthetic. This is a combination of mineral and synthetics. It is called the optimal choice for "VAZ-2109". The semi-synthetic is completely superior to mineral oils, but a little inferior to synthetic. It does not react to a low temperature. If you do not want to spend big money on synthetic lubricant, take semi-synthetic.

With a relatively soft winter in your region in VAZ-2109, you can pour all-season compounds that have average viscosity indicators. They are well shown at a moderate cold and with a strong heat.

From manufacturers it is worth highlighting such:

• ESSO ULTRA;
• Zic a + or xq;
• Shell Helix;
• Elf Sporty;
• Spectrol;
• Castrol GTX;
• Agip Super Motor Oil;
• Mobil 1;
• KIXX;
• ROSNEFT, etc.

Yes, domestic oils cost cheaper, but can significantly give up according to the characteristics of imported compositions for engines. Therefore, try to choose high-quality oils, because savings can lead to serious undesirable consequences.

Required volume

When you were determined with the manufacturer and the degree of viscosity of the engine oil, you need to figure out the required quantity.

The bulk of oil in the VAZ-2109 car engine is 3.5 liters. But experienced motorists advise to take a canister for 4 liters. The balance you will gradually add to the carter as it consumes until the next scheduled maintenance.

Usually, the liquid agrees every 100 - 300 mileage kilometers. To check the level, use the oil dipstick. Oil imprint on it should remain between the marks of the minimum and maximum values. If the level is committed to a minimum, the absence of the missing amount of lubrication.

It is strictly forbidden to mix different types and even the manufacturer of the composition. If you do not know what oil in the engine is used in the engine, it is recommended to change it immediately and in the future to fill only that is in the crankcase.

When a bus owner cannot acquire the same oil that was previously used, the fluid replacement is carried out with a mandatory washing. Here it is easy, but it is important because so different oils are not mixed with each other. Otherwise, it will negatively affect the operation of the engine and in the state of its nodes.

Methods of replacement

There are 2 ways to self-shift the working fluid in the engine:

• Without flushing. The usual procedure that provides for only drainage and fill a new composition in Carter.
• With washing. Washing additives, special washing oils, or the oil you are going to pour can be used here.

Additives are added to the engine when there is still old oil, after which it is started at idle, allow you to work for 10 minutes, and then follow a simple instruction. Or you need to drive a number of kilometers with additives. It all depends on the specific type of additives and manufacturer's instructions.

Washing oils are used otherwise. They can be poured into the engine, pre-draining the old lubricant, after which the motor is launched and drained.

Similarly, motor oils are used as flushing. The essence is to change the liquid 2 - 3 times with an interval of about 200 - 400 kilometers.

The use of ordinary oil is the most optimal solution, since the crankcase does not remain traces from additives or flushing compositions.

Materials and tools

To change in the engine "VAZ-2109" oil, you will need to take:

Do not forget about your own security. Since you will merge hot oil, there is a risk of getting it on your skin. To avoid burns, wear tight clothes, closed shoes, gloves and glasses.

Stages of replacement

The procedure for replacing the oil in the engine "VAZ-2109" is conditionally divided into 3 stages:

• draining testing;
• filter change;
• pouring a new engine fluid.

Try to strictly follow the instructions on how to change the engine oil yourself. This will avoid unwanted errors.

The design "VAZ-2109" is quite simple, access to all nodes to replace lubricant is easy, which does not cause problems even with newbies.

Drain of work

To begin with, it is important to get rid of the old lubricant to the full lubricant, filled into the power unit of your nine. To do it, you need:

In order for the oil to be faster, it is necessary to get rid of the vacuum in the upper part of your "VAZ-2109" power unit. It is made extremely simple. You need to remove the lid of the oil-tapping neck.

When you managed to completely merge the old work, you can start replacing the filter. Although it is usually done at that time until the remains of oil from the "VAZ-2109" flow into the container. As soon as you get free, go to the oil filter.

Filter change

The next step of replacing the oil in the VAZ-2109 car engine will dismantle the old and installing a new oil filter.

First return to the place of the plug hole, replacing the sealing ring on it.

The filter itself is dismantled manually, a special pulp or a girlfriend tool. In the absence of a filler and when manually, the case is not amenable, take a simple scolding, let's push it across the case of the filter and use the tool handle as a lever.

After dismantling the filter, take a new element, apply a small amount of fresh oil onto the screw sheet on its seal and threaded notches. It will simplify the installation process and prevent the adhesion of the gum.

To protect the motor from oil starvation during the first start of the engine with a new oil and filter, fill the body of the filter element with a lubricant by about 50% of its volume.

It is installed manually element, use the tool and apply excessive force for installation, otherwise you risk simply break the filter.

Pouring new oil

When all previous stages of work are successfully completed, it remains for small.

To pour motor fluid to the desired level, follow the instructions.

1. If you did not open the fuel plug during the drain of testing, now it will be for sure to remove it. On "VAZ-2109", it is dismantled by rotation counterclockwise.
2. Now take the canoe or cut the neck of the bottle. Insert the fixture into the dummy hole, open the canister with fresh lubricant and begin to fill it gradually.
3. Enough viscous, therefore filling the Carter will be gradually. Do not rush to pour all 3.5 liters at once, since part of the old fluid in any case remains inside the system.
4. First, fill about 3 liters. Wait a few minutes until all the oil stalks. Take the oil dipstick and check at what level the lubricant in the crankcase is now. If its oil, plot a little more.
5. It is necessary to ensure that the oil film on the probe showed the level of exactly between the MIN and MAX marks. If you fill more necessary, the surplus will have to merge. Therefore, it is better not worth a hurry.
6. When the oil is at the required level, close the lid and run the motor. Give the power unit to work at idle for 3 to 4 minutes. Wait until the dashboard does not go out the pressure control lamp.
7. Mock the engine, wait a few more minutes. Re-insert the dipstick and measure the level of the engine fluid.

Everything, on this work on self-replacement of oil in the engine of the domestic car "VAZ-2109" can be considered completed.

But do not forget after a few days of operation, re-perform the level of fluid level. Sometimes car owners for non-accuracy or inexperience do not tighten the drain plug or turn the oil filter to the end. Of them begin to flow oil, which leads to a drop of its level.

Tighten all connections, add liquid to the desired level.

Increased oil consumption in the VAZ-2109 motor indicates troubleshooting. If you just regularly add or change the oil, you do not fix the situation. The car needs diagnosis and repairs to eliminate the causes provoked an increase in appetite with respect to this working fluid.

One of the key nodes of any machine is a power unit. Motor service life is largely affected by the overall reliability of the vehicle. To extend the motor testing, it is necessary to take care of the timely replacement of oil in the VAZ 2109 engine. First you need to figure out which oil to fill.

Motor oil varieties

There are several different types of lubricants for engines of cars that we will briefly consider now to make it easier to make the right choice.

Mineral

Traditionally, such oils are made on a mineral basis, but they are poorly suitable for VAZ 2109 engines. The fact is that they do not meet the requirements for the replacement of oil and do not satisfy the tight operational characteristics of the power units.

Such oils for VAZ 2109 are also made on a mineral basis, but they add some synthetic components to improve the characteristics of lubricants during the cold start of the motor. Semi-synthetic oils support the purity of the inner surfaces of the motor and securely protect it from wear.

Synthetics

On basic synthetic oils, motor oils are created with high performance characteristics. They are suitable for pouring both gasoline and diesel power units. Guarantee reliable protection against wear and well lubricate working mechanisms even at the moments of cold start. Synthetic oils minimize friction harmful to the engine and maintain it in full purity. They satisfy the highest quality standards on the API system and correspond to the tolerances of automotive companies.

All-season oil

All-season oil can be any of the above. It is intended for the operation of the engine in a temperate climate and suitable for year-round use. In the winter months, such oils almost do not thicken, and in the heat under the influence of high ambient temperatures, the lubricant is not very strong. Similar oils for VAZ 2109 include lubricants that have the following parameters for SAE: 5W-40, 10W-40, 15W-40.

Features of oil replacement

Filter and Tube Location

Replacing the oil in the VAZ 2109 engine - the process is not the easiest, but you can cope with this case if necessary. If you buy a used car from another person, you need to replace the lubricant in the engine, as soon as possible. It is recommended to wash the engine with a special fluid, as you are not known exactly that it was flooded earlier.

The oil is also recommended to change if you have not exploited the VAZ 2109 for a long time. When the motor do not harde it for a long time, condensate accumulates in it and stirred with lubricant, causing the deterioration of its property and as a result, increasing the wear of all the inner parts of the power unit.

In order to extend the service life of the oil filled into the engine, we will unsubscribe dramatically or accelerate hard. We strongly recommend that you pour a certain type of oil for every season - winter or summer. Always refuel only high-quality fuel on verified gas stations. Dirty fuel burns not completely, causing lubricant contamination.

Methods for replacing oil

If you want to know how to change the oil in the VAZ 2109 engine with your own hands, you will be interested to know that there are two ways to do it:

1. Without flushing the power unit before the fill of the oil.
2. With washing the aggregate. In this case, a special flushing fluid is poured to the bottom of the probe, the motor is hardened and leave to work for 10 minutes at idle, after which the oil is drained.

What is required to replace?

To replace oil in the VAZ 2109 you will need a filter, suitable oil, and if necessary, washing liquid. Also be robbed with rags and prepare a set of keys.

The amount of oil in the VAZ 2109 engine reaches 3.5 liters, but in practice only 3 liters typically fit into the motor. What oil pour into the VAZ 2109 engine you can learn from the car operating manual, but we recommend flooding semi-synthetic or 10W-40 synthetics from Castrol, Shell or domestic brands that have more accessible cost.

So, how many oil liters in the VAZ 2109 engine and which oil choose you know, and therefore you can start the process of replacing the lubricant liquid.

We merge the old lubricant

So that the oil is better merged from the engine, pre-warm the motor. Heat the car on the overpass or the observation pit, and you can also use the lift or lift it with the help of a jack in a flat place. Raise the front of the car by laying the stops under the wheels.

Place the tank for a drain plug, disconse it with the key and carefully unscrew your hands. Be careful and do not bother, as the motor we pre-warmed. When draining the oil, it is recommended to unscrew the lid of the oil-tank neck, which will speed up the drain process (vacuum will be disappeared at the top of the motor).

We change the filter

After draining the oil from the VAZ 2109, you need to screw the bolt into the drain hole and unscrew the oil filter. If you do not have a special key, and you cannot unscrew the filter with your hands, use a conventional screwdriver: Junk the filter across and use it as a lever for twisting. Next, lubricate the gasket and threads of the new filter and gently push it to not thread the thread. When you twist it, do not use the key, but do all your hands. It is also recommended to fill the new oil filter by approximately half to prevent oil starvation in the first instantaneous operation of the motor after starting.

So that the engine worked securely, efficiently and long, it is extremely important to monitor the quality and amount of oil in it.

For VAZ 2109, the recommended frequency of oil change in the engine is 10 thousand mileage kilometers. But it is necessary to navigate to your specific situation. Practice shows that the replacement is sometimes carried out noticeably more often.

Causes of replacement

There are conditions that need to be adhere to that the lubricant present in the engine system performed its protective functions, and turned into the cause of the failure of the power unit.

There are several basic moments when the oil replacement should be carried out.

Regardless of the recommended replacement time, always pay attention to the current motor lubrication state. Various factors can serve to premature oil throughout, so it will have to replace it before. Plus, additionally, eliminate the reasons, because of which the lubricant did not work out the period allowed.

For the summer, it is used more viscous lubricant than for the winter. With long-term operation in the motor, it loses its properties, additives, particles of chips from the driving parts of the engine begin to adversely affect its condition. Over time, if you do not change the lubricant, it may lead to the need for overhaul of the power unit.

A little about oil

Before proceeding with the replacement procedure, you need to know what and in what quantity should be poured.

In cars, VAZ 2109 is usually poured from 3 to 3.5 liters of lubricant to the motor. At the same time, it is recommended to acquire a capacity of 4 liters, so that you have the opportunity to add the lubricant used as it is possible.

Periodically check the dipstick at what level there is a lubricant. Optimally - this is that the oil trail remained between the maximum and minimum mark. Golden mean. Fill above the maximum mark should not be exactly, just like riding with the scalred lubricant.

With the volume of oil we decided. And what exactly should it be?

If you take into account the quality of quality, the optimal solution for the VAZ 2109 will be synthetic lubricant. But she is the most expensive. The semi-synthetic is more affordable, but high-quality characteristics are lower. If finances do not allow at all, you can do with mineral oil. But it is better not to save on this question.

In no case do not mix different brands of oil, and when replaced, first rinse the system with a flushing composition, then pour a new liquid.

Replacement

Now proceed directly to work. There is nothing complicated here, because even the newcomer will cope with the task.

1. Prepare in advance the container where you will drain the spent lubricant from the engine. An ordinary plastic bottle of 5 liters is quite suitable. Plus, the funnel will need not to miss and do not shed oil to the floor.
2. Heat the engine. On the hot engine, the oil becomes less viscous, which allows it to more effectively and quickly exit the system during drain.
3. Put the machine on a flat surface, turn on the manual brake.
4. Start removing the old lubricant. For this, the engine protection is removed if there is such.
5. Submire the carcard to the pallet to the drain and unscrew the key to 17 drain plug.
6. Do not forget, the oil is hot, so unscrew the carefully, in order to avoid burns.
7. After removing the drain plug, wait about 10-15 minutes until all the oil is solved into the prepared container.
8. In parallel with the oil replacement in the motor, it is recommended to change the oil filter. This can be done while the lubricant mercy. The filter is unscrewed by a special key or screwdriver, breaking through the housing. A new oil cleaner is mounted in its place.
9. When the lubricant is completely stalking, return the plug into place.
10. Fill some oil into a new filter. It is necessary to do this in a few approaches so that the element manage to absorb the substance. The bay of approximately half the filter level is enough.
11. Be sure to treat the filter sealing gum and wipe dry by dry winding site of the filtering device. Put the filter into place, tighten it with your hands.
12. Next you will need either just pour fresh butter or rinse the system. Now in any auto parts store you can find a variety of flushing facilities. Take one of them and follow the instructions. After completing the washing, you can pour a new lubricant.
13. For the fill, open the cover on the engine and start the liquid through the funnel to gradually.
14. Fill about 3 liters and wait until the lubrication is distributed over the system.
15. Gradually, there are another 500 milliliters of fluid. In parallel, control the amount of oil in the crankcase using the probe. If you are not washed the system, you will probably have to fill a little less than 3.5 liters. This is due to the imperfection of the draining system.
16. Make sure that the probe show the mark between the maximum and minimum lubrication level.
17. Tighten the lid, run the motor and let it work for some time at idle. This will allow liquids to fill the filter, channels.
18. Running the engine, you will light up a red oil pressure indicator lamp. Still 10, it will go out. If the lamp does not go out, most likely, you poorly screwed the filter. Check out.
19. Move the engine, take the probe again and check what is the real level of lubricant in the crankcase. If required, add some liquid to the optimal level.
20. By completing the work, be sure to check the system for the absence of traces of oil lifettes. If the defense was dismantled, return it to the place.

Replacing the oil VAZ 2109 does not represent complexity, which allows the car owner to perform this work independently, saving on the services of the workshops of the service station.

Even with a minimum of work experience, every car owner will be able to independently perform all the necessary service work.

Preparing for replacement

The manufacturer plays an axervice interval at 10,000 mileage kilometers. It is recommended to perform a regular change of oil, which will allow to ensure the performance of the car engine.

What oil pouring

VAZ cars are traditionally unpretentious to the quality of technical fluids, which allows the use of inexpensive car shoes. Plant The manufacturer recommends using lubricant with viscosity indicators in 5W-30.

Engineers advise using viscous compositions, which allows you to reliably protect the moving elements of the power unit, and at the same time cooling the motor.

We can recommend you to use inexpensive semi-synthetic, which provides high-quality motor lubrication and at the same time having an affordable cost. Remember that by acquiring semi-synthetic, you must consider the volume of the engine of your car.

Engine oil volume

First of all, you need to define you need to purchase for this work. The volume of oil in the car VAZ 2109 car is 3.3 liters. When conducting service work, 3 liters of technical fluid change.

Note that the oil volume in the engine depends on the specific modification of the power unit, so you need to clarify this data in the technical documentation for your car.

Where to fill the oil

The procedure for replacing oil on VAZ 2109 does not represent complexity. Opening the hood, you can see on the engine the cover of the plug-in neck. Remember only that opening it with a hot engine is not recommended.

Instruments

To perform this work, you will need a flat screwdriver in case of problems with the oil pump and the key to 17, which we will unscrew the plug in the pallet.

You also need to take care of the presence of vessels and capacity of 3-4 liters for old oil.

Remember that at the same time the oil filter is replaced, so you will purchase it in advance in the auto parts store.

Step-by-step instruction

Replacing the oil in the VAZ 2109 engine does not represent complexity. Every car owner will cope with this work. We offer you a step-by-step instruction for performing this service.

Service work does not depend on the specific volume of the engine in the VAZ 2109 and the modification of the power unit.

1. Previously, you need to warm up the engine, for which we let it work for about 5 minutes.
2. The car is rushing on a garage or overpass pit. With a certain proportion of skills, it is possible to carry out all the work without a pit and overpass. In this case, you need to gently climb under the car and substitute a flat container for the old lubricant under the carter.
3. We find a drain plug on the pallet crankcase and a key to 17 unscrew it. The dark waste fluid will flow out of the crankcase. We are waiting for it until it follows, usually it takes 20-30 minutes.
4. After that, we change the filter that is unscrewed manually without using the tool. In rare cases, the filter carving can be rusted, and it is impossible to unscrew it manually. In this case, you can use the special key or simply break the filter housing with a screwdriver and act like a lever.
5. As soon as the old auto shock stops from the drain plug, you need to twist a new filter, then screw the plug in place and gently clamp it with the key. Spinning filter, you should pour a little oil into it and lubricate the rubber gasket, which will not allow her to burn to the thread and provide better sealing of the system.
6. We unscrew the plug plug located on the head of the cylinder block. We recommend pouring the oil using a funnel, which will avoid spilling it into the engine. Subsequently, such spilled liquid will burn long and cause an unpleasant odor.
7. The bay of three liters should check the dipstick, which will determine how much butter you flooded into the engine. If necessary, the fluid should be addressed so that the level is between the maximum and minimum.
8. We close the filler cork and start the car. Give the Motor to work for a few minutes, then drip the engine and check the level of motor samples again.
9. Inspect the car for the presence of outers and, if necessary, tighten the oil filter or drain plug in the crankcase.

On this, the oil change in the engine VAZ 2109 is completed.