Safe ride requires automotive tires, as the pressure in Lada Grant's tires changes. Their size must be the corresponding recommended pressure indicators. Since the verification of this parameter is an important point, for this apply a special device - a pressure gauge. It serves to measure the pressure level. In this case, the results should be compared with the recommended values.

It is important to use only high-precision pressure gauges with the smallest declared error. If a pressure is revealed during measurements, which is less recommended, it can cause accelerated wear of the tires, deterioration of controllability and stability of the car, since the angles of the wheels are changed.

The tire pressure, which is recommended by the manufacturer, is indicated in the tables. It is measured in kg / m² in front and rear wheel tires at partial and full load. The tables indicate the pressure in the car's tires of Lada Grant Sedan and Liftbek. The dimension of the tire depends on the configuration, which is divided into suite, the norm and standard.

It should be borne in mind that the air pressure in, the equipment of which refers to the standard category is different from other similar versions of the norm or suite. The difference is expressed in one hundred. The first equipment is equipped with smaller wheels.

The ideal option is to support such a level of this indicator, which was installed by the manufacturer. A partial load involves not more than 3 adults in the car, as well as the lack of luggage or cargo in it. If the trunk has a cargo, the weight of which is 50 kg, and there are 3 people in the car and more, then it implies a full load.

Similar tables are provided for by the manufacturer in the salons of cars and liftbek. The location of the table is the central rack from the driver's seat.

When the car moves, the indicator also increases. Correctly check the air pressure in the Tires of the Lada Grant car can only be using a pressure gauge. At the same time, the level of their temperature and ambient air must have the same value.

How to properly check tire pressure?

The view of the car's carpet of Lada Grant can be normal and under reduced parameter level. It is impossible to judge this parameter for external signs. To check its compliance with recommended indicators, measurements should be carried out.

The pressure in the tires of any car, including the Lada Grant, can not be constant, regardless of whether the winter tires on wheels or summer. In conditions of elevated temperature, an increase in the indicator. If it is lowered, the pressure that winter tires is experiencing.

Tire pressure should be the magnitude of constant independent of weather conditions

At a temperature difference, constituting from 10 ° C to 15 ° C, check this parameter. It is almost inconspicuous, since winter tires are not heated due to frosty air and low pavement temperatures.

Summer tires are poorly cooled due to warm air flow and heated road surfaces. These factors increase the indicator by 0.2-0.3 bar. To reduce it, you need to prepare a compressor or pump, as well as a pressure gauge. All actions must have a certain sequence.

A secure ride on any car will be directly dependent on what state is the wheels. It is important to prevent the tires quickly wear out.

How to carry out measurements to increase the life of the Lada grants?

A certain equipment of Lada Grant car has appropriate standards for which its level of the test parameter is characteristic.

If the pressure in the tires when moving the car Lada Grant is not a corresponding standards recommended by the manufacturer, then the wheels of this model will be subjected to premature wear.

If the tire parameters change markedly them should be checked for gas leakage

With a tangible fall, the tire indicator should be checked for air leaks. It is possible that the reason is only in this, then the spool comes or simply replace the new one. If it is established that the spool is working, and the pressure decreased, then the reason can be covered in the tire malfunction. It may have been depressored by its special protective layer, then its dismantling is made by a special device.

If the wheel balancing check is carried out, which remained normal, then the alignment should be started from the tire of a special place where the valve is located. After all works, the tire must be mounted according to the mark.

For more uniform wear of tires, the wheels should be rearranged every 30 thousand km of mileage. For this purpose, the following actions are carried out:

1. Inspect the tires of the Grant Lada with disks to make sure that there are no cuts, bundle of tire rubber.
2. Check the steel cord for the presence of places subject to corrosion due to moisture penetration.
3. Caps on wheels must be unscrewed to check the pressure in the tires.
4. If it is found that the indicator is greater than the required, then pressed on the spool tip so that a certain part of the air was released from the tire.
5. Next again proceeds the indicator.
6. With a constant drop of the indicator, using the cap and the key, the spool wrap as much as possible.
7. To check the spool for tightness, moisten the valve hole.
8. When air bubbles appear, you need to replace the spool on the wheel.
9. Measurement with the help of a caliper of the residual depth of the tread tread, is replaced if the depth size of the device is 1.6 mm or less.

In the absence of caliper, the depth can be checked visually in accordance with the wear parameters of the tire, which may look like stripes located across the tread. Wheels pull up if necessary.

Preparing the Lada of the grant to operate in winter, must be replaced with summer tires used in the summer. Winter tires should be used necessarily if the car is not planned to be installed during the cold season.

OUR PARTNERS:

Site about German cars

Lamps used in the car

Any modern passenger or truck can be serviced and repairing independently, in the usual garage. All that will be required - a set of tools and a factory repair manual with a detailed (step-by-step) description of operations. Such a guide must contain types of used operational liquids, oils and lubricants, and most importantly - the torque of all threaded connections of parts of the components and car units. Italian cars - Fiat (Fiat) Alfa Romeo (Alpha Romeo) Lancia (Liancha) Ferrari (Ferrari) Mazerati (Macerati) have their own design features. Also in a special group you can Allocate all French cars - PEUGOUT (Peugeot), Renault (Renault) and Citroen (Citroen). German cars are complex. This applies to Mercedes Benz (Mercedes Benz), BMW (BMW), Audi (Audi) and Porsche (Porsche), in a little less - to Volkswagen (Volkswagen) and Opel (Opel). The next large group, isolated on constructive features is American manufacturers Chrysler, Jeep, Plymouth, Dodge, Eagle, Chevrolet, GMC, Cadillac, Pontiac, OldSmobile, Ford, Mercury, Lincoln . From Korean firms should be noted Hyundai / Kia, GM - Dat (Daewoo), SsangYong.

Most recently, Japanese cars had a relatively low initial cost and affordable prices for spare parts, but recently they caught up with these indicators prestigious European brands. And this applies to almost the same degree to all brands of cars from the rising sun country - Toyota (Toyota), Mitsubishi (Mitsubishi), Subaru (Subaru), Isuzu (Judza), Honda (Honda), Mazda (Mazda or as said before Matsuda) , Suzuki (Suzuki), Daihatsu (Daihatsu), Nissan (Nissan). Well, and cars released under the Japanese American brands Lexus (Lexus), Scion (Singing), Infinity (Infinity),

Proper tire pressure is a very important aspect of secure movement by car. Although this indicator can be called relative, as it denotes the ratio of the proportion of the air to the volume, and not simply measures its amount in the tire. But it is necessary to carry out such measurements constantly, because systematic control will ensure safety when driving and the durability of components of the car. Measurements are carried out using a special instrument called a pressure gauge. They are different types and various accuracy classes. Therefore, for permanent use, you should choose a high-quality device with a high accuracy class.

Cars of domestic manufacturer Lada Grans are popular even in the current days. All because the price of them is small, and even the average family with an average earnings can afford that car. The ratio of price and quality approximately coincides, although some Lada models still receive many negative reviews on the forums. Owners of such cars often do not think about which pressure standards must be observed. Do not even know where such parameters are indicated. Such information can be found from the instruction book. There, the manufacturer describes what indicators for which modification are suitable. Also indicate information about tire sizes suitable for such cars, and the amount of atmospheres for each of the options.

Tire manometer

In tires, the dimension of 13 inches permissible norms at partial load are 1.9 atmosphere. And with full loading, up to 2.1 bar on the rear tires increase. But already the wheels having a dimension of 14 inches, it is necessary to pump up to 2.0 bar. With the maximum load, the authors should be 2.2 bars on the rear axle tires. The total carrying capacity of the car is 475 kilograms.

On a note.

After the car's tires are pumped on the tire, it is desirable to check the atmospheres level by their own pressure gauge on arrival home.

Very often, employees of such organizations do not bother, and download all the tires up to 2.0 bar. And such indicators can be overestimated or understated for a particular car brand. Therefore, the pump should be monitored independently. Due to improper pressure, there may be a lot of problems. For example, unchanging tires can lead to:

• rapid erasure of lateral protector on rubber;
• overheating tires and their premature damage;
• violation of car manageability, especially on turns;
• fuel reservoir.

There are some advantages of unchanging tires:

• soft drive car;
• no noise and rattling inside the car.

But the disadvantages clearly overlap all the advantages. To then not spend money on new rubber, it is better to adhere to the permissible norms.

Packed wheels also do not well affect the status of components and parts of the car:

• the suspension is quickly wear out;
• the average protector on rubber is erased;
• auto rides hard;
• in the cabin heard rattles and all the bodies and potholes on the road are felt.

Plus consists only in fuel economy, but it is not necessary to rejoice at such a fact. Disadvantages here clearly overlap all the advantages.

Pressure measurements are necessary only after a three-hour downtime after a trip, on the cold tires.

Pressure in the wheels "Lada" in winter

In winter and summer time, the pressure inside the tire changes due to the temperature differences of the environment. For example, in summer, when it is very hot, the air inside the tire is heated and its volume increases. Therefore, the wheels need not to download a little, about 0.3 atmosphere. And in the winter there is exactly the opposite. Due to the low temperature, the air volume in the tire decreases, and therefore they should be poured by 0.3 atmosphere.

Very important is where the car is located. If it is in the warm room, then when measuring the pressure, the pressure gauge will show optimal indicators. But it is worth going outside in the cold, then the indicators in the tire will fall about 0.4 bar. And the car will already go to the unchanging tires, and it is unsafe. Therefore, throwing up the wheels in the garage and overstate the rates of norms, as they fall in the cold.

On a note.

Another factor is the workload of the car. If the wheels are already pumped to the necessary parameters taken into account when cold, and the machine is loaded as much as possible, in this case, you need to still take into account the manufacturer's recommendations, relative to the indicators with increased workload. As a result, it turns out that it is necessary to pump up with a decrease in pressure during cold and at maximum load.

Fans of "Lada Kalina" Universal often do not think about tire pressure changes at different times of the year. For such cars, the optimal indicators are 2.2 atmospheres on the wheels of the front axle, and 2.3 on the rear. Most drivers agree with the manufacturer's recommendations and do not note strong discomfort when driving. But in winter, many depart from these standards. In the frost, the front rubber is pumped up to 2.0 bar, and the rear up to 2.2 bar. This is taking into account the fact that the tires on the car are factory. If the car is transferred to the wide-profile rubber, then the pressure indicators are increasing. The front should be 2.4 bar, and behind - 2.5 bar. Low profile and narrow tires require 1.9-2.0 atmospheres on the front axle, and 2.0-2.2 - on the back.

The "Lada" sedan Vesta has a greater maximum load capacity than the previous model. The lifting index is up to 615 kilograms. The instructions indicate pressure parameters equal to 2.1 atmospheres, and both for the front wheels and for the rear. With an increase in the load, the rear wheels are rolled up to 2.2 bar. Such indicators are characteristic of tires R15 and R16. But in winter it is better to keep the pressure within 2.2 bar. The manufacturer recommends performing measurements of the amount of air in the tire at least once a week. And also such an event must be carried out before a long trip.

Pressure in the tires "Lada Vesta Cross" has some other parameters. Factory wheels on the car are R17, so the front wheels require pumping to 2.2 atmospheres, and the rear to 2.4. But if tires are installed another value, then you need to focus on the overall pressure table of the "Lada".

Fans of the Largus model should know that the atmospheres indicators in this car are higher than in the previous models under consideration. The pressure in the wheels "Largus" for tires R14 and R15 is 2.4 bars on the front axle, and 2.6 on the back. But the owners of such cars note that with such parameters the machine is very rigidly rigid, therefore, the recommended testimony often unders. At the same time, strong wear of rubber is not marked. But it is not necessary to get involved in an understatement, as this can lead to a pile of problems. If the driver is a fast ride lover, then the pressure drop on 1.0 bar will be quite justified. Rubber at high speed is heated, and the air volume increases, so it will not have such a decrease.

Tire pressure indicators on "Lada Liftbek" in the summer

The manufacturer's prompt relative to optimal pressure indicators can be found on the central pillar of the driver's door. According to it, the amount of atmospheres in a similar car should be 2.0 atmospheres on all four wheels with minimal loading. The maximum load capacity provides for a change in the indicators up to 2.2 bar on the rear axle and 2.0 bar on the front.

In the summer, if the car is in a cool garage, the indicators will be alone, and when the car leaves the heat, the amount of air in the bus will increase. Therefore, before the trip it is worth lower than the pressure, about 0.3 bar. So it turns out to achieve the most correct parameters that are declared by the manufacturer. The most important thing in this case is to follow the behavior of the car. If the car lies on a turn or a fuel reservoir was seen, then immediately need to check the pressure and bring to optimal indicators. Otherwise you have to buy new details and tires.

Pressure check should be carried out by the driver systematically. If you constantly forget about such trifles, it may entail a lot of consequences. Moving on the car along the busy highway with improper pressure, you can endanger not only yourself, but also other drivers and pedestrians.

Lada Granta is a budget car of Russian production. The front-wheel drive sedan was appreciated by drivers. Attractive appearance, calm and dynamic ride, a spacious trunk, a comfortable salon, good noise insulation and specifications - this is not a complete list of its advantages. The manufacturer took into account the features of domestic roads and developed a car that behaves perfectly on them.

Like any other machine, this requires an attentive relationship. During operation, it is necessary to change not only consumables, but also monitor the condition of the wheels. Qualitatively to perform their functions to them allows the air pressure that is inside. Under the action of certain factors over time, it changes. The increase occurs after movement, the decline in the cold season.

Conduct measurement is necessary regularly. Ideally do it every day, but, as practice shows, not everyone turns out. It will be enough to control the status of the tire once a week. The indicator depends on the size of the wheels and the workload of the car. Information about how pressure should be in the Lada grant sedan, is given in the form of a table.

Dimensions and pumping air pump Lada Granta Sedan

Pressure in Lada Lada Grant Liftbek

* Partial load - When there are no more than 3 adults in the car, there is no cargo in the trunk.

Full load - when in a car 3 or more people, and in the trunk weighing 50 kg.

* Moment of tightening wheel bolts 70-90 N * m

In winter, the tire pressure is reduced by 7 kPa (1 pound per square meter) for every 7 ° C (12 ° F) temperature decrease.

To the question, "what tires can be put on a grant" can not be answered unequivocally. As in cases with other machines, the selection of tires and disks is the priority task of each driver, since the correct selection will ensure a comfortable and safe ride.


In order to choose the right size and find out which tires are better for Lada Grant, many factors should be disassembled that directly affect the choice.

Sphere of influence of tires and disks

To understand what tires on Lada Grant will fit well, you need to know the first to know what the amount of tires and discs affect the car. Experts with one hundred notes that when replacing tires, it should be guided by the difference in the external diameter it was minimal.

Selection of tire affects such features of the car operation:

• characteristics of brakes and traction;
• transmission;
• fuel consumption;
• atmospheric emissions.

An increase in the radius of the wheel, tires and disks have the following effect.

Legend: + - improvement, - - deterioration, 0 - no change.

Changing the size of the tire will definitely lead to changes in the accuracy of the vehicle management. Since the volume of the tire becomes larger, the scale of the space in contact with the road bladed increases. This provides ample maneuverability.

Factory characteristics of tires and disks for Ladagranta

According to the factory characteristics, the original tires on the grant from the plant have R14 and R13 radius.
R14 is a fairly classic option for small cars. Both discs and rubber with these dimensional characteristics are characterized by budgetary and find them in the market is quite simple. Similarly, the situation is also with R13. Therefore, by analyzing which discs are approached by a load, you should keep the current moment in your head.

The dimensional characteristics of tires and disks, which are also suitable for Ladagranta
To date, all AvtoVAZ models that have front-wheel drive are equipped with R15 size discs. And although the original Lada Grant R15 tires with this disk model have dimensional characteristics of 185/55, they also fit well to tires 175/70, 185/60 and even 195/55.

Pressure in the tires of the grant of the basic factory configuration, namely R13 and R14 with partial load looks like this:
R13 (175/70) - 0.19 / 0.19 (1.9 / 1.9)
R14 (175/65) - 0.20 / 0.20 (2.0 / 2.0)
Data is presented in the ratio of "kg / cm2".
Grant Sport tire pressure is approximately at the same level adjusted to the dimensional characteristics of the wheel, namely R16.

Permanent control of the level of tire pressure ensures the safety of movements and is the prevention of wear of the tires. If the pressure will be at a reduced level (below the indicator of 1.9 atmospheres), then the lateral parts of the tread, due to the uneven air distribution when driving, will wear much stronger. When pumping tires (above the value of 2.0), the middle part of the tread will suffer, which is also fraught with its consequences.

The list of negative consequences from uneven pressure distribution in the tire:

1. the scale of contact with the road expands;
2. fast and uneven tread wear;
3. reduction of manageability by vehicle;
4. the potential danger of creating an emergency on the road.

For correct measurement of pressure in the tires, a pressure gauge will be needed. Measurements should be carried out after a while after the trip so that the air in the tires can cool after intensive heating when driving. The optimal value of the value (for R13 - 1.9, for R14 - 2.0) is indicated in the form of a number that can be found on the gas tank or car door. It is important that during the use of the pressure gauge, the air did not leave the wheel.

The resulting value must be compared with optimal and run to the desired one. For wheels, which are located in parallel and on one axis, it follows that the pressure level is identical.

Is it possible to install wheels with dimension R16 205/55 on Lada Grant

The wheels with radius R16 and dimension 205/55 are not suitable for both the regular configuration of Ladagranta and the Sport model. Because of too large diameter, they will be too tight to fit that when driving will lead to a rapid wear of the testers and a decrease in car maneuverability. The owners of Lada Grant recommend at R16 radius to install 195/50 or 205/45.

Winter tires for Ladagranta

Selection of winter rubber for the Lada Grant should be carried out on the basis of the characteristics of the area, which will have to ride. If the roads will not be cleared enough, and winter threatens frequent thaws that change the frosts, then in this case the studded rubber should be used.

Tires for winter use should be gently in contact with the roadbed, which will ensure a reliable degree of clutch even on the rolled snow, and the tread base should be tough so that control is accurate. Goodyear, Pirelli anddinlopWinTeraprospace the desired dimensional characteristics for Lada Grant, namely, ranging from R13 to R16.

Winter tires will also require run-in, which will allow them to become firmly in the landing jacks. For high-quality running, it will take about 500 kilometers. When running, you should try to avoid sharp braking and slip. To improve the clutch with the road, it is also recommended to choose a tire with a narrow profile.

Summer tires for Ladagranta

High-quality summer tires must provide a high level of clutch both dry and on wet asphalt, as well as smoothness. Tires must have a wide profile, and for this it is best suite with dimensional characteristics R14 185/60 or R14 175/65.

Short check list - how to buy rubber on Lada Grant

1. Search for the necessary tires should be kept in mind the size factory characteristics. The size of the selected tires should converge with these data.
2. Pay attention to the tread pattern. Comfort depends on it in many ways.

3. Pay attention to the width parameters. On acceleration and braking of the car affects the width of the spot converging with the road cannon.
4. Special attention should be paid to the landing diameter. Tires that will have an excessive height or width can damage the suspension, the narrow tires will increase the load on the bearings.
5. It is important to take into account the maximum speed index and the lifting index.
6. DataTREADWEAR, TRACTION, TEMPERATURE and MAXPRESSURE allow you to learn the Ozavodskoy tire wear, brake properties, temperature resistance and the maximum pressure level for the tire, respectively.

Video - wheels on Lada Grant Liftbek Suite. Honest feedback

Video - New LS discs and rubber Pirelli on a grant